Wednesday, October 31, 2012

FAGOR - 1LF-0115 _ DISHWASHER_ DISASSEMBLE PROCEDURE_ Failure Error Codes_Contn:


Contn:

Remove 2 screws fixing the door lock.




Push it down and remove the front panel.



Remove 4 screws fixing the panel



Remove the sub seal connector, which is attached to the detergent drawer housing.



Remove the wire that connected to the valve.



Remove the valve connection.



Remove detergent drawer housing ass'y.



Remove the wire that connected to parasite filter.



Remove the power cable group as it is showing the picture.



Remove the wire that connected to pressure switch.





Remove the pressure switch as it is showing the picture.


Remove the pressure switch hose handcuffs and pressure switch hose as it is showing the picture.


Remove one screw fixing the door cover.


Remove the wire that connected to the door lock.


Remove pipe clip that fixes the drain hose.


Remove the pipe clip fixing the tub outlet hose.


Remove the wire that connected to the pump motor.


Remove 4 screws fixing the pump motor.


Remove the wire that connected to resistance.


Remove one nut fixing the resistance.


Remove 4 screws fixing the front counterweight on the front and pull it up.


Hold the gasket and gasket body fixing spring together, and pull them up.


Remove 2 pim fixing the shock absorber.



Remove four screws fixing the spring hanger sheet iron.


Remove the washing group as it is showing the picture.


Remove 3 screws fixing the upper counterweight.


Remove the belt as it is showing the picture.


Remove one screw fixing driven pulley.


Lay down the machine with an angle of 45 Degree to the floor.  Disconnect wires and remove 2 screws fastening the motor under the tub.  Pull the motor for disassembley.  


Remove the 17 screws fixing tub.



ERROR CODES

Failure code.
Failure indicator.
Probable failure.

Err 1
The start/pause
light blinks
The door is not
shut properly.

Err 2
The program
ready light
blinks.
The water level
in your machine
is below heater.
The pressure of
your water
supply may be
low or locking.

Err 3
The start/pause
light and
program ready
light blinks .
The pump has
failed or the
pump filter is
obstructed.

Err 4
The program
end light blinks.
There is an
excessive
amount of water
in your machine.

Err 5
The start/pause
light and program
end light blink.
The heater of
your machine or
the heat sensor
has failed.

Err 6
The program
ready light and
program end light
blink.

The motor has
failed.
Err 7
The start/pause
light,program
ready light and
program end light
stays on
permanently.

Configuration
error.
Err 8
The start/pause
light,program
ready light and
program end light
blink.

The motor has
failed.
Err 9
The program
ready light and
program end light
stays on
permanently.
The network
voltage is too
high or too low.

FAGOR - 1LF-0115 _ DISHWASHER_ DISASSEMBLE PROCEDURE




Remove the 2 screws that fix the top plate at the back.



Push the top-plate back, and pull it up.


Remove 2 screws that fix the door.


Pull up the door.


Remove 9 screws that fix the door group.


Remove the door inside plastic as it is showing the picture.


Remove the door hinge as it is showing the picture.


Remove the door glass as it is showing the picture.


Remove the door handle as it is showing the picture.


Remove the door handle pim, as it is shown the picture.


Remove door handle spring as it is showing the picture.


Remove the door lock tongue as it is showing the picture.


Pull the Gasket as it is showing in the picture.


Remove the Gasket body fixing string.


Remove the detergent drawer and pull it up carefully.


Remove 5 screws which fix the control panel to the front panel.


Remove two screws fixing the control panel.


Remove one screw fixing the detergent box group.


Pull the control panel up.


Remove wires as it is showing the picture.


Remove 4 screws fixing the electronic card.


Remove the electronic card as showing the picture.


Remove the kickplate as it is showing the picture.


Remove 2 screws fixing the front panel at the bottom.


Contd: