Thursday, January 31, 2013

PANASONIC TX-32LX60 _ TX-26LX60 _ SERVICE MODE _ ADJUSTMENTS _ DISASSEMBLE _ Main Voltage Points & Voltages _ White Balance Adjustment





HOW TO REMOVE PEDESTAL

  • Lay the main unit face down.
  • Remove the 2 fixing screws and hinge cover.
  • Remove the 8 fixing screws and the pedestal assembly.


TO REMOVE BACK COVER
  • Remove the 2 fixing screws and hinge cover.
  • Remove the 16 fixing screws.
  • Carefully remove the back cover and disconnect two AV3 wires.


CHASSIS BOARD LAY OUT

Board Name &  Function
  • A-Board  à Main Board
  • B-Board à Tuner
  • H-Board à AV3 Terminal
  • Key Control à Key Control
  • K-Board Mains Input à Power Switch
  • P-Board à Power Supply
  • V-Board à Remote Receiver, LED IR, Bats.
A-BOARD [NORMAL MODE]
            Test point Position --> Voltage
  • TP004 à C870, + pin 33V ± 3V
  • TP005 à Connector A7, pin 22 12V [15V]
  • TP006 à C1500, + pin 8V ± 0,3V
  • TP008 à C1700, + pin 5V ± 0,2V
  • TP010 à C890 - R898 3,3V ± 0,1V
  • TP012 à Q878, pin 1 3,3V ± 0,1V
  • TP017 à C872, + pin 10,5V ÷ 16V
  • TP018 à IC252, pin 5 24V
  • TP019 à IC862, pin 1 24V
  • TP023 à Connector A7, pin 12 24V
Standby mode
  • TP009 à C883, + pin 1,8V ± 0,1V
  • TP013 à C868, + pin 3,3V ± 0,1V
P-BOARD [NORMAL MODE]
  • TP001 à Connector P2, pin 20 12V ± 2V [15V± 2V]
  • TP002 à Connector P2, pin 8 24V ± 2V
  • TP003 à Connector P2, pin 9 24V ± 1V
Standby mode
  • TP002 Connector P2, pin 8 24V
  • TP003 Connector P2, pin 9 <2V
SELF CHECK
  • Self-check is used to automatically check the bus lines and hexadecimal code of the TV set.
  • To enter Self-Check mode, keep pressing the STATUS button on the remote control and press the down (-/v) button on the TV set.
  • To exit Self Check, switch off the TV set at the power button.
TO ENTER SERVICE MODE
  • Set the Bass to maximum position, set the Treble to minimum position then keep pressing the INDEX button on the remote control and press the down button (-/v) on the TV set, this will place the TV set into the Service Mode 1.
REMOTE CONTROL KEY FUNCTIONS DURING SERVICE MODE
  • Press the RED / GREEN buttons to step up / down through the functions.
  • Press the YELLOW / BLUE buttons to alter the function values, to alter White Raster use +/- buttons
  • Press the OK button after each adjustment has been made to store the required values.
  • To exit the Service Mode, press the "N" button.
Setting indication [Note:  All setting values are approximate.]
  • Sub-Contrast à Sub-Contrast 23 à Receive a 80% white level Philips Pattern with correct sound system (B/G, D/K) via aerial input. For Sub-Contrast alignment press "Blue" button, wait until the figure color is changed from red to black color.  Press the OK.
  • DVCO à DVCO 4 à Receive a 80% white level Philips Pattern via aerial input. For DVCO alignment press "Blue" button, wait until the figure colour is changed from red to black color. Press the OK.
  • Sub-Brightness à Sub-Brightness 0 à Optimum setting.
WHITE BALANCE ADJUSTMENT
  • Switch on the TV Set. Enter Service1. Step down to Highlight line and keep the aging time more than 20 minutes.
  • After aging time above set White Raster No.12 for Highlight and No.4 for Lowlight Press the OK button to store.
  • Put Minolta Sensor to the center of the LCD Panel with 25mm gap between Minolta Sensor and LCD Panel. Adjust "x" and "y" values by changing Red and Blue values.
  • Press OK button to store setting.
Item
Value

Highlight
x= 0,275±0,005

y= 0,275±0,005
Lowlight
x= 0,275±0,005
y= 0,285±0,005

PANASONIC CT-36HL42F_CT-36HL42UF_CT-36HL42CF _ SERVICE MODE






TO ENTER SERVICE MODE

When minor adjustments need to be done to the electronic controls, the method of entering the service mode without removal of the cabinet back is as follows using the remote control:
  • Select SET-UP icon and select CABLE mode.
  • Select TIMER icon and set SLEEP time for 30 Min.
  • Press “ACTION” twice to exit menus.
  • Tune to the channel 124.
  • Adjust VOLUME to minimum (0).
  • Press VOL (decrease) [ < on receiver
  • RedCHKappears in upper corner.+
  • After receiver is set into service mode, set TIMER back to NO.
TOGGLE BETWEEN AGING AND SERVICE MODES
  • While the “CHK” is displayed on the left top corner of the CRT, pressing “ACTION” and “VOL” UP on the TV simultaneously will toggle between the modes. Red “CHK” for service and yellow “CHK” for aging.
  • Press POWER on the remote control to display the service adjustment modes menu, select adjustment by pressing the volume right/left buttons and channel up/down buttons on the remote and ACTION to enter the adjustment.
  • Some adjustments are available only in some modes (480i, 480p, 1080i); it is needed to apply the format.
  • A 1080i, 480p, 480i pattern can be obtained from Panasonic’s TU-DST51 set-top box DTV decoder.
 TO EXIT SERVICE MODE  [Method-1]
  • This TV goes out from service mode when it is unplugged or turned OFF.
  • To exit the service mode, turn the TV OFF or unplug the TV from AC.
[Method - 2]
  • Press ACTION and POWER on the receiver simultaneously for at least 2 seconds.
  • The receiver momentarily shuts off; then comes back on tuned to channel 3 with a preset level of sound.
  • Any programmed channels, channels caption data and some others user defined settings will be erased when exited by pressing ACTION and POWER on receiver.  
  • Always check that the TV exits the service mode.
TO CHECK COLORS
  • Press RECALL on the remote control when in service mode (red “CHK” is displayed) to enter the purity field check mode.
  • Press RECALL again to select desired field.
  • Toggles [NORMAL SCREEN à WHITE SCREEN à RED SCREEN à GREEN SCREEN à BLUE SCREEN  à AND BACK TO NORMAL SCREEN  à THE CYCLE REPEATS]
ENTERING SERVICE MODE WITHOUT REMOTE CONTROL [BACK OPENED]
  • While the receiver is connected and operating in normal mode, momentarily short test point FA1 (A15 pin 2) to cold ground (A-Board).
  • The receiver enters the aging mode.
  • Yellow letters “CHK” appear in the upper left corner of the screen.
  • (The VOLUME up/down will adjust rapidly).

PANASONIC CT-36HL42F_CT-36HL42UF_CT-36HL42CF _ LED BLINKING CODES _ DISASSEMBLE PROCEDURE


AUTO DIAGNOSIS

This receiver incorporates a new auto-diagnosis feature. With this new feature will be easier for the repair technician to detect the failures. There is a LED located on the A-Board by the DG-Board, this LED will start flashing when a failure is detected by the circuits located in a specific area, depending on how many times the LED is flashing, this will tell you what circuit should be checked.
LED LOCATION

SOS of diagnosis LED

NUMBER OF FLASHES
POSSIBLE CIRCUIT

1
+140 (POWER)
2
LOW DC (+B)
4
HHS (HIGH VOLTAGE)
5
IC4511
6
IC4518
DIS-ASSEMBLY FOR SERVICE

BACK COVER
  • Remove all the screws marked with an arrow [ ß ] from the back of the receiver.   4 screws at the top edge of the receiver.  3 screw by the A/V jacks.
  • 1 screw by the RF jacks.
  • 1 screw at each lower corner of the receiver.
  • 1 screw by the retainer plate of the AC power cord.
  • 1 screw at each lower side of the receiver.
  • 1screw below the A/V jacks
  • Extensions for board connectors may be needed to test voltages on P-Board.
A-BOARD REMOVAL
  • The DG-Board is assembled on the main chassis (A-Board). The A-Board assembly rest on a chassis tray along with the D-Board.  Slide chassis tray out. Gently lift, tray and pull out.  Disconnect plug connectors; release wire ties and holders as required for complete chassis removal.
[1]  A-Board is secured to the chassis tray with five screws.
[2]  The D-Board is secured to the chassis tray with three screws
[3]  The A-Board is mated to the D-Board by four flexible connectors: A4, A5, A6 & A7 (D4, D5, D6 & D7 on the D-Board, respectively).
  • To remove either boards, unplug the connectors on the A-Board.
  • Some tie-wraps that secure the wire dressings may need to be unfastened for chassis removal.
D-BOARD GROUND CONNECTOR
  • To release the GND cable from D13 connector insert a wire in both cavities of connector, then pull up the cable.

L-BOARD [CRT OUTPUT]
  • Plugs into the socket on the CRT neck.
  • To remove this board, first unplug the board from the CRT neck, then disconnect L1, L2 and L3 connectors, to disconnect the focus F1(red cable) & F2 (white cable) cables, pull the tab and release the cables, finally disconnect the screen cable from the D-Board D16 (screen and heater).
  • To reinsert back the cables, remember the original position of cables, F1 (red cable) goes to A on the CRT socket and F2 (white cable) goes to B on the CRT socket.
  • To release screen GND cables from L-Board L11 & L12 connectors, insert a wire in both sides of connector and pull upwards the cable, then remove the wire.


DG-BOARD
  • Plugs onto the A-Board at the A21, A22 and A23 (DG21, DG22 and DG23 respectively) connectors.
  • This board is not-serviceable. When removing this board pull carefully.
P-BOARD
  • Plugs onto the right side of the D-Board at D3, D2, D11 & D12 connectors (P3, P2, P11 & P12 on P-Board, respectively); First remove the three screws that holds the metal board, one from the flyback and two from the chassis tray and then use a flat head screwdriver to release the connector locking tabs and pull upwards the board.
G-BOARD
  • Mated to A-Board by three flexible connectors (A1, A2, A3) and D-Board by one flexible connector (D40). To remove this board, first unplug the four flexible connectors, then RT4 and G4 connectors, then pull upwards the board while unlock the tabs from the chassis tray.
K-BOARD
  • Is fastened to the G-Board by two metal brackets that are secured by a screw (each one). Plugs into the front of G-Board by connector K1 to G6,and is fastened to the chassis tray assembly by 2 screws on each lower corner.
SPEAKERS
  • Each speaker is secured to a plastic base with 4 screws, and each plastic base is secured to a second base with two screws, and assembled to the cabinet with two screws.  The subwoofer speaker is assembled within the back cover of the television set by 4 screws.
  • Be sure to reconnect the speaker wires to the correct speaker lead (+) (-)


  • IMPORTANT: Since two different versions of DG-boards are available for the CT-36HL42 models, please check board number printed on the lower right corner when replacing DG-Board. Refer to label on chassis for EEPROM part number that is used.
  • The DG-Board (TNPA2345 or TNPA2345AC) is non-serviceable.  If this board is defective replace it with a new one. Each version of DG-Board must be matched with correct version of EEPROM.  Confirm the EEPROM part number before replacing.
  • When ordering any board, add and ” S” after the board suffix application. 
  • Example: If ordering D-Board, should be ordered as: TNPH0466S.

PANASONIC TC-17LA1_TC-20LA1 _ BACK-LIGHT BOARD REMOVAL & LCD PANEL DISASSEMBLY




BACK LIGHT BOARD REMOVAL

  • Remove the rear cover.
  •  Remove the screws (6 pcs) and the screws (2 pcs) (TC-20LA1) / (1 pcs) (TC-17LA1) and detach the shield plate and Inverter plate (U, D).

  • Disconnect the couplers (AP10, BL4 and BL6) and remove the screws (2 pcs) and detach the BL-Board.
  • Caution:  PCB Fixing screws driving torque: 0.2-0.3 N·m (2-3kg·mm).  Do not tighten screws so hard.

  • Disconnect the couplers (AP10, BL4 and BL6) and remove the screws (2 pcs) and detach the BL-Board.

LCD PANEL
  • Remove the screws (6 pcs) and the screws (2 pcs) (TC-20LA1) / (1 pcs) (TC-17LA1) and detach the shield plate and Inverter plate (U, D).

  • Disengage the shaft holder hook and detach the power button shaft.
  • Disconnect the coupler (AP8) and detach the circuit board K bracket with K-Board.

  • Remove the screw (1 pcs) and the screws (4 pcs) and detach the lock hinge plate.
  • Remove the screw (1 pcs) and disconnect the couplers (B2 (AP2) and B3 (AP3)) between B-Board and the AP-Board.
  • Disconnect the couplers (AP4, AP6, BL4 and BL6) and the flexible cable (AP9 and DG3 (TC-20LA1)/ DG4, DG5 (TC-17LA1)) and remove the screws (7 pcs) and detach the APBoard, DG-Board and BL-Board.

  • Remove the screws (2 pcs), detach the LCD panel.
Caution:  PCB Fixing screws driving torque: 0.2-0.3 N·m (2-3kg·mm).  Do not tighten screws so hard.

PANASONIC TC-17LA1_TC-20LA1 _ SPEAKER _ B-BOARD & K-BOARD REMOVAL




SPEAKER REMOVAL
  • Remove the rear cover.
  • Remove the screw (1 pcs) and the screws (4 pcs) and detach the lock hinge plate.
  • Remove the screw (1 pcs) and the screws (4 pcs) and detach the lock hinge plate.
  • Remove the screw (1 pcs) and the screws (6 pcs) and disconnect the couplers (V2 and V3) and the Speakers (L,R).
  • Caution:  PCB Fixing screws driving torque: 0.2-0.3 N·m (2-3kg·mm).  Do not tighten screws so hard.
B-BOARD REMOVAL
  • Remove the screw (1 pcs) and the screws (4 pcs) and detach the lock hinge plate.
  • Remove the screw (1 pcs) and disconnect the couplers (B2 (AP2) and B3 (AP3)) between B-Board and the AP-Board.
K-BOARD REMOVAL
  • Remove the screws (6 pcs) and the screws (2 pcs) (TC-20LA1) / (1 pcs) (TC-17LA1) and detach the shield plate and Inverter plate (U, D).
  • Disconnect the coupler (AP8) and disengage the hook (2 pcs) and detach the K-Board.

PANASONIC TC-17LA1_TC-20LA1 _ DG-BOARD & V-BOARD REMOVAL




DG-BOARD REPLACEMENT PROCEDURE

  • Remove the rear cover.
  • Remove the screws (6 pcs) and the screws (2 pcs) (TC-20LA1) / (1 pcs) (TC-17LA1) and detach the shield plate and Inverter plate (U, D).

  • Remove the screw (1 pcs) and the screws (4 pcs) and detach the lock hinge plate.
  • Disconnect the flexible cable (DG1 and DG3 (TC-20LA1)/DG4, DG5 (TC-17LA1)) and remove the screws (2 pcs) and detach the DG-Board.


  • Caution:  PCB Fixing screws driving torque: 0.2-0.3 N·m (2-3kg·mm).  Do not tighten screws so hard.
V-BOARD REMOVAL
  • Remove the screw (1 pcs) and the screws (4 pcs) and detach the lock hinge plate.
  • Remove the screw (1 pcs) and disconnect the couplers (V2 and V3) and the flexible cable (V9) and detach the V-Board

  • Caution:  PCB Fixing screws driving torque: 0.2-0.3 N·m (2-3kg·mm).  Do not tighten screws so hard.