Wednesday, December 31, 2014

SAMSUNG 50 Inch PLASMA TV - PN50C450B1DXZA - HOW TO ACTIVATE POWER and LOGIC BOARD TEST PATTERNS WITHOUT MAIN BOARD

PN50C450B1DXZA - HOW TO ACTIVATE POWER and LOGIC BOARD TEST PATTERNS WITHOUT MAIN BOARD
HOW TO ACTIVATE POWER and LOGIC BOARD TEST PATTERNS WITHOUT MAIN BOARD
> Remove the power cord to panel.
> Short highest 2 pins # on logic board test jig (can be 4 pin or 6 pin)
> Remove power connector at main board; Keeping connection to SMPS.
> Short “Power On” Pin to circuit ground on Power connector to SMPS.
> Connect Power cord to Panel.
Power Supply Trouble Shooting Notes
  Do not  run with the “X” or “Y” main disconnected. The SMPS will shut down immediately. However if a meter is first connected to the test point when power is applied it will read the correct voltage briefly before shutting down. (You have enough time to check key voltages)
  Do not reconnect any connectors to SMPS or Y/X Boards until power has been turned off long enough for Vs to drop below 10V or damage will occur to X or Y Boards.
Over Current Protection
For the SMPS Power Supply
 If a short circuit occurs on either the VS or VA voltage lines, the SMPS stops operating, but should not fail. When the short circuit is removed from the source line, the Power Supply will operate normally again. Many SMPS Supplies are replaced needlessly.
SAMPLE VIEW – READINGS & VITAL SIGNS
  When troubleshooting, It’s very important to first check Vs, Va, Vsc & Ve If Vs is missing (0V), disconnect power and check for short. Use ohm meter to measure resistance while disconnecting Y-Board & X-Board supply feeds one at a time.  Turn Power On and Test SMPS with short connector removed for correct Vs voltage verification. (It may only come up briefly but to full level). Again be careful not to reconnect Power Connectors until Vs falls below 10V.
If Va is low or missing, disconnect Supply Feed to Address Boards and Check to see if SMPS Supply is restored. (Note Va feed normally passes through the Y-Drive to the Address Boards (Logic Buffer Boards).
  If Vsc is low or missing and Vs was OK, the failure is with the Y-Board since the Y-Board generate the Vsc voltage from the Vs supplied by the SMPS.
  If Ve is low or missing and Vs is OK, the failure is with the X-Board since the Ve is generated by the X-Board from the Vs supplied by the SMPS. Note:  in some rare cases the Ve may be generated by the Y-Board feed to the XBoard.)
Other SMPS Voltages
Check Low Voltage feeds to the Main Board and other supplied Assemblies.
Click on the Pictures to Zoom In.

NAKAMICHI SoundSpace 10-11–12- 21 – Remote Control Schematic Diagram.

How to disassemble the remote control _ Circuit diagram [Remote Control Unit (SS-10/11/12/21)] _ Nakamichi Soundspace 10/11/12/21
REMOVAL PROCEDURE
* Open F01 (Battery Cover).
* Remove screws F02 (4 pcs.), F03 (1 pce.) to detach F04 (Bottom Cabinet Ass'y) and F05 (Front Panel Ass'y)
* Remove screws F06 (4 pcs.) to detach F07 (Main P.C.B. Ass'y) from F05 (Front Panel Ass'y).
* Remove screws F08 (2 pcs.) to detach F09 (Sensor P.C.B. Ass'y) from F04 (Bottom Cabinet Ass'y)
MECHANISM DISASSEMBLE
SCHEMATIC DIAGRAM & PWB
CLICK ON THE PICTURES TO MAGNIFY

HOW TO ENTER SERVICE MODE - SONY HCD-EC68P - EC78P _ RESET

SONY HCD-EC68P/EC78P _ TEST MODE

COLD RESET
The cold reset clears all data including preset data stored in the memory to initial conditions. Execute this mode when returning the set to the customer.
1. In the standby status, press the [Standby/Power] button to turn the power on.
2. Press three buttons of [Stop
], [FUNCTION] and at last [Standby/Power] simultaneously.
3. When “RESET” appears, the set enters standby status.
PANEL TEST MODE
1. In the standby status, press the [Standby/Power] button to turn the power on.
2. Press three buttons of [DISPLAY], [Stop], and [FUNCTION] simultaneously.
3. When the panel test mode is activated, LEDs and segments of the liquid crystal display are all turned on.
Version Check
1. In the panel test mode (all LEDs and segments of the liquid crystal display are turned on), press the [FUNCTION] button.
2. On the liquid crystal display, date and version are displayed “xxxxxxxx”. For example, “1114V102”.
3. From this status, press the [Pause] button, and the destination and model name are displayed. For example, “CE2” and “ESLO–”.
4. To release from this mode, press three buttons of [DISPLAY], [Stop], and [FUNCTION] simultaneously.
Key Test Mode
1. In the panel test mode (all LEDs and segments of the liquid crystal display are turned on), press the [DISPLAY] button.
2. The message “KEY0 0 0”displayed. Whenever any buttons are pressed and the [VOLUME] dial is turned, the value is changed.
3. To release from this mode, press three buttons of [DISPLAY], [Stop], and [FUNCTION] simultaneously.
CD REPEAT 5 LIMIT CANCEL MODE
Number of repeats for CD playback is 5 times when the repeat mode is “REPEAT”. This mode enables CD to repeat playback for limitless times.
1. Press the [Standby/Power] button to turn the power on.
2. Press the [FUNCTION] button to select CD function.
3. Press three buttons of [DISPLAY], [Stop], and [|◄◄ – ] TUNING ◄◄ -- ] simultaneously.
4. It enters the CD repeat 5 limit cancel mode and displays “NO LIMIT”
5. To release this mode, press the [Standby/Power] button to turn the power off.
CD SHIP MODE
This mode can run the CD sled motor optionally. Use this mode, for instance, when cleaning the optical pick-up.
1. Press the [Standby/Power] button to turn the power on.
2. Confirm there is no disc in all trays.
3. Press the [FUNCTION] button to select CD function.
4. Press two buttons of [CD ] and [Standby/Power] simultaneously.
5. Set to the CD ship mode. (chucking on)
6. After blink “STANDBY”, “LOCK” is displayed, disconnect the AC plug.
CD TRAY LOCK
This mode is for the antitheft of CD disc in shop. (not for transport) Procedure:
1. Press the [Standby/Power] button to turn the power on.
2. Press the [FUNCTION] button to select CD function.
3. Insert a disc.
4. While pressing the [Stop
] button, press the [Eject] button for more 5 seconds.
5. The message “LOCKED” is displayed and the disc tray is locked. (Even if exiting from this mode, the disc tray is still locked)
6. If press the [Eject] button to eject the disc, the message “LOCKED” is displayed and cannot eject the disc.
7. To release this lock, while pressing the [Stop] button, press the [Eject] button for 5 seconds again.
8. The message “UNLOCKED” is displayed and the disc tray is unlocked.
CD POWER MANAGE
This mode is for switch the CD power supply on/off. Even if this state pulls out AC plug, it is held.
1. Press the [Standby/Power] button to turn the power on.
2. Press the [FUNCTION] button to select CD function.
3. Press the [Standby/Power] button again to turn the power off (standby).
4. After pressing the [DISPLAY] button, while pressing the [Stop] button, press the [Standby/Power] button.
5. It turns power on and displays “CD POWER”, then display “ON” or “OFF”.
CHANGE-OVER THE AM TUNING INTERVAL (Except EC78P: UK model)
The AM tuning interval can be changed over 9 kHz or 10 kHz.
1. Press the [Standby/Power] button to turn the power on.
2. Press the [TUNER/BAND] button to select TUNER (AM) function.
3. Press the [Standby/Power] button again to turn the power off (standby).
4. After pressing the [DISPLAY] button, while pressing the [TUNING +►►; ►►|] button, press the [Standby/Power] button.
5. It turns power on and display “9k STEP” or “10k STEP”, and thus the tuning interval is changed over.
CD SHIP AND COLD RESET
1. Press the [Standby/Power] button to turn the power on.
2. Confirm there is no disc in all trays.
3. Press the [FUNCTION] button to select CD function.
4. Press three buttons of [PLAY MODE/TUNING MODE], [|◄◄ – TUNING] and [Standby/Power] simultaneously.
5. After blink “STANDBY”, “RESET” is displayed, disconnect the AC plug
COMMON TEST MODE
1. Press the [Standby/Power] button to turn the power on.
2. Press three buttons of [PLAY MODE/TUNING MODE], [TUNING +►► FFW], and [DISPLAY] simultaneously.
3. It enters the common test mode and displays “COMMON”.
4. Each time the [VOLUME] dial is turned, “VOL MIN”, “VOL 16”, and “VOL MAX” are displayed.
5. To release from this mode, press three buttons of [PLAY MODE/TUNING MODE], [TUNING +
►► ►►|], and [DISPLAY] simultaneously.
CD SERVO TEST MODE
This mode can check the servo system operations of the optical pick-up system (= optical unit + CD board).
Note1: Do not enter the [CD SERVO TEST MODE] while any other test mode is in progress.
Note2: Do not enter any other test mode while the [CD SERVO TEST MODE] is in progress.
How to Enter the CD Servo Test Mode
1. Press the [Standby/Power] button to turn the power on.
2. Press the [FUNCTION] button to select CD function.
3. Press three buttons of [CD►, |◄◄  ], [◄◄ – TUNING] and [DISPLAY] simultaneously.
4. It enters the CD servo test mode and displays “BDT S CU”.
How to Exit from the CD Servo Test Mode
1. Press three buttons of [CD ], [|◄◄ , ◄◄ – TUNING] and [DISPLAY] simultaneously.
2. It releases from the CD Servo Test Mode and returns to the ordinary CD function.
CD SERVICE MODE
This mode can move the SLED of the optical pick-up, and also can turn the optical pick-up laser power on and off.
1. Press the [Standby/Power] button to turn the power on.
2. Press three buttons of [CD ], [TUNING + ►►, ►►| ], and DISPLAY simultaneously.
3. Press the [FUNCTION] button to select CD function.
4. It enters the CD service mode and displays “SERVICE”.
5. To exit from this mode, press three buttons of [CD
], [TUNING + ►►, ►►| L] and DISPLAY simultaneously.
Key Operation:
[TUNING +►►, ►►|], [|◄◄,  ◄◄ – TUNING]:
Use these keys to move the SLED. When [TUNING +
►►, ►►|] is pressed in this mode, the SLED moves to outer circumference and the message “SLED OUT” is displayed.
When [
|◄◄,◄◄  – TUNING] is pressed in this mode, the SLED moves to inner circumference and the message “SLED IN” is displayed.
DISPLAY
Use this key to turn the optical pick-up laser power on and off. When the laser power is turned on, the message “LD ON” is displayed. When the laser power is turned off, the message “LD OFF” is displayed.
CD ERROR CODE
The past errors of the CD mechanism (CDM) are displayed as the CDM Errors, and those of the optical pick-up system (= optical unit + CD board) are displayed as the BD Errors.
1. Press the [Standby/Power] button to turn the power on.
2. Press the [FUNCTION] button to select CD function.
3. Press three buttons of [TUNING +
►►, ►►|], [Stop and [DISPLAY] simultaneously.
4. Then, the CDM error code is displayed as “M0xxxxxx” (x means hexadecimal number) on the liquid crystal display as shown below.
5. Every pressing of the [TUNING +
►►, ►►|] button in this mode increments the number after “M” starting from “M0” up to “M9”, and then returns to “M0”. Every pressing of the [|◄◄,◄◄ – TUNING] button in this mode decrements the number after “M”. The smaller the error code number is, the newer the error content is.
6. When the [PLAY MODE/TUNING MODE] button is pressed then, the BD error code is displayed as “D0xxxxxx” (x means hexadecimal number) on the liquid crystal display as shown below. In the same way as the CDM error code, use of the [TUNING +
►►, ►►| and the [|◄◄,◄◄– TUNING] buttons in this mode enables tracing of the error history.
7. To release from this mode, press the [I/1] button to turn the power off.
Contents of “CDM Errors”
Error display example
M 0 FF 11 42
1 2 3 4
1 It indicates the error history number 0 to 9: The error code number 0 indicates the newest error.
2 It indicates whether the CDM error occurs in the normal operations or during the initialization operation.  FF : The error has occurred in the normal operations.  Other than FF : The error has occurred during the initialization operation.
3 It indicates the processing during which the trouble has occurred.
01: The disc EJECT processing is in progress.
02: The disc INSERTION-WAITING processing is in progress.
03: Processing of the disc INSERTION-REQUEST for the upper CD tray is in progress.
04: Processing of the disc EJECTION-REQUEST for the upper CD tray is in progress.
05: The disc pulling-in operation is in progress.
06: The disc chucking processing is in progress.
07: The disc re-chucking processing is in progress.
08: The disc chucking-release completion operation is in progress.
4 It indicates the operation during which the trouble has occurred.
00 : Waiting for the operation.
10 to 13 : The disc EJECT operation is in progress.
20 : The disc pulling-in operation is in progress.
30 : The disc chucking-release operation is in progress.
40 to 43 : The disc EJECT operation due to error is in progress.
Contents of “BD Errors”
Error display example
D 0 02 09 01
1 2 3 4
1 It indicates the error history number.  0 to 9: The error code number 0 indicates the newest error.
2 It indicates the error content
01: The focus servo cannot lock-in.
02: GFS is no good (NG).
03: The startup time exceeds the specified period of time (time over)
04: The focus servo is unlocked continuously.
05: Q code cannot be obtained within the specified period of time.
06: The tracking servo cannot lock-in.
07: Blank disc
3 It indicates the on-going processing of optical pick-up system (= optical unit + BD board) when the trouble has occurred.
01: The CD SHIP mode processing is in progress.
02: The POWER OFF processing is in progress.
03: The INITIALIZE processing is in progress.
04: The optical pick-up system (= optical unit + BD board) is in the stop state.
05: The STOP operation is in progress.
06: The startup processing is in progress.
07: The TOC read-in processing is in progress.
08: The SEARCH operation is in progress.
09: The PLAY operation is in progress.
0A: The PAUSE operation is in progress.
0B: The PLAY – MANUAL SEARCH operation is in progress.
0C: The PAUSE – MANUAL SEARCH operation is in progress.
4 It indicates the operation that is being processed when the trouble has occurred.
It indicates the step number of each processing specified by 3.  Because the numbers of steps are different in each processing, this number is different in each processing.
CD FACTORY MODE
Note1 Do not enter the [CD FACTORY MODE] while any other test mode is in progress.
Note2 Do not enter any other test mode while the [CD FACTORY MODE] is in progress.
1. Press the [Standby/Power] button to turn the power on.
2. Press the [FUNCTION] button to select CD function
3. Press three buttons of [CD
], [FUNCTION], and [DISPLAY] simultaneously.

Tuesday, December 30, 2014

POWER AMP & POWER SUPPLY SCHEMATIC - SONY HCD-EC68P- HCD-EC78P

Circuit Diagram for Power Amplifier & Power Transformer Section_Sony HCD-EC68P- HCD-EC78P
Canadian Model-UK ModelHCD-EC78P
Australian Model _ HCD-EC68PC68P/EC78P
SCHEMATICS
Click on the pictures to Magnify

SONY HCD-EC68P- HCD-EC78P - COMPACT DISC RECEIVER - HOW TO DISASSEMBLE CD-MECHANISM

How to disassemble CD mechanism _ replace the belt _ Sony HCD-EC68P- HCD-EC78P - COMPACT DISC RECEIVER HCD-EUS Model
HCD-EC68P/EC78P
Canadian Model; UK Model
HCD-EC78P
Australian Model; HCD-EC68PC68P/EC78P
MECHANISM DISASSEMBLY
CLICK ON THE PICTURES TO ZOOM IN

Saturday, December 27, 2014

XOCECO – DYNEX -32 Inch LCD TV – SMPS SCHEMATIC

Power supply Regulator Board Circuit Diagram _ Dynex & Xoceco – 32” LCD TV
Used ICs - TL431ACD_TLP421_SSC9500 _ FSDH321
SMPS SCHEMATIC {CLICK ON THE SCHEMATIC TO MAGNIFY}

Wednesday, December 24, 2014

JBL CS360 Xcite - 3.1 HTS - SCHEMATIC [Circuit Diagram]

CS360Xcite - 3.1- channel powered surround home audio system JBL_ Circuit Diagram 
POWER SUPPLY [SMPS]
POWER AMPLIFIER
INPUT STAGE
CLICK ON THE SCHEMATICS TO ZOOM IN

Monday, December 22, 2014

JBL BASS-2 - BASSWAVE - SCHEMATIC - POWERED SUB-WOOFER

Bass-2 Bass-wave - JBL - Powered Sub-Woofer _ Schematic Diagram & Exploded View
EXPLODED VIEW
SCHEMATIC

Saturday, December 20, 2014

SONY KLV-22BX300-KLV-32BX300-KLV-26BX300-KLV-40BX400 - Service mode _ LED Blinking Codes

KLV 22BX300 - KLV 26BX300 – KLV-32BX300 KLV40 BX400 [RM-GA019] – SERVICE MODE – LED BLINKING CODES - SONY LCD TV
Accessing Self Diagnostic Menu
* While TV on standby mode, press the following sequence on the Remote commander. (RM-GA019) Display >5 > Vol
> Power.
* To Reset Error Count & Error History Press 8 > 0 key
* To Reset Panel Operation Time Press 7 > 0 key
*
To exit, turn the power off using Remote.
Accessing Service Mode
* While TV on standby mode, press the following sequence on the Remote commander. Display >5 > Vol
> Power.
* Use the ▲/▼ button to select the item you want to refer and press Ø for details.
GAISOU Adjustment
When new board is replaced, confirm the color ornamental of the TV set.
* While TV on standby mode, press the following sequence on the Remote commander. Display >
5 > Vol > Power.
* Use the▲/▼ button to select the GAISOU.
* Use the ◄/► button to change the GAISOU data. [For example if color is Red than should select 03 in the service mode of the TV set.]
SELF DIAGNOSTIC FUNCTION
> When safety shutdown occurs, Standby LED display reports the cause by using the lightning patterns as indicated here.
The figure shows LED display when SHUTDOWN is caused by Balancer Error. It repeats flashing for a specified number of times in 0.5sec/cycle and has a 3 seconds interval of lighting off.
Note that a 3 seconds interval of lighting off is fixed regardless of abnormal state types.
LED BLINKING CODES
CLICK ON THE PICTURES TO MAGNIFY

Thursday, December 18, 2014

HOW TO TAKE OUT DISC AT EMERGENCY - harman/kardon - BDP1/BDP10 - Blu-ray Players

TO TAKE OUT DISC
Retrieve a Blu-ray/DVD/CD disc from the tray without power
This method will allow you to retrieve a disc without power in the BDP1/10 or pull out the disc tray if needed.
* Remove all screws holding the top cover on: four screws at the rear and four on the sides. Remove the top cover.
* Tip the unit up to view the bottom of the chassis near the front panel; there are two open slots under the disc mechanism.
(With one free hand, reach inside the unit to support the Blu-ray/DVD/CD disc; it may fall out when you release the loader mechanism in the next step.)
In the slots, you can see a white bar inside. 
* Using a small flat-blade screwdriver, move the slotted bar as far to the right as it will go; this will unlock the loader mechanism and free the disc.
The disc should now be free and can be pulled out the rear of the loader mechanism, if it has not fallen out already. 
Now move the white bar back to the left, to its original location.
NOTE:  There is also a method where you can open the tray without removing the top cover, but in the process of tipping the unit up to slide the mechanism release, the disc may drop out of the tray (and may possibly scratch the disc) and into the unit, so you would still need to remove the top cover.  
In this method, you will need to locate the white locking bar under the unit as described above, without tipping the unit upright. Once this is done, open the hinged tray door with your fingernail. 
Use a pair of long-nosed pliers to reach in and pull the tray out of the loader, exposing the disc.

BDT 30/230 - BDT 3/120 Blu-ray player - harman/kardon - SMPS Circuit diagram

harman/kardon - BDT 30/230 - BDT 3/120 Blu-ray player – SMPS schematic – General troubleshooting – Firmware update Procedure.
SPECIFICATIONS
> Supported disc formats: 5-inch (12cm) or 3-inch (8cm) Bd-video (single-layer or double-layer), Bd-R, Bd-Re, DVD-video, DVD+R/+RW, dvd-R/-RW, CDDA (CD digital audio), CD-R/RW discs
> Region code (BD/DVD): A/1 (BDT 3); B/2 (BDT 30)
> Audio formats: DOLBY digital, DOLBY digital Plus, DOLBY Truehd, dTs digital, DTS-HD high Resolution
> Audio, DTS-HD Master Audio, PCM, CBR @192kbps, vBR @ 355kbps, MP3: 32kbps – 320kbps bitrates, including variable bit rate encoding still-image format: JPEG video signal system: NTSC (BDT 3); PAl (BDT 30)
> HDMI version: 1.4a with 3-d and 30/36-bit deep color
> Power requirement: Ac 110 – 240v, 50/60hz
> Power consumption: 25W maximum, <0.5W standby
> Dimensions (h x W x d): 2-5/8" x 17-5/16" x 13-7/8" (66mm x 440mm x 352mm)
> Weight: 8.2 lb (3.7kg).
* 06-RC2410-A001 REMOTE CONTROL
* 08-0BDT30-PWY ASSY-POWER BOARD
* 43-FS512S-216 DC FAN 5012F 320MM
Preparation to upgrade software
1 Power on the set and press “settings” button on the remote.
2 Press left cursor to select "Information". Check the Software Version.
3  Check that the software version is correct in the UPG folder.  For example: if the software version is displayed as “BDT20 XX.XX.XX”, the correct software is “BDT20_BD.bin”. Otherwise, the software is “BDT2_BD.bin”.
4 Start the CD Burning software and create a new CD project (Data Disc). Copy the UPG folder to the root directory of the data disc.
5 Burn the data onto a blank CDR.
Upgrade software via CDR
1 Power on the set and insert the prepared Upgrade CDR.
2 The set will start reading the disc .
3 When the BDT recognizes the disc, press Setting > System > System >  Upgrade > Disc. Follow the instructions on the screen.
4 About 3 minutes later, the BDT will automatically turn off, when upgrade has been completed.
Upgrade software via USB Flash Drive
1 Decompress the packed file, copy the UP G folder to the root directory of a USB memory device.
2 Insert the USB. The player will recognize the USB device automatically.
3 Press Setting > System > System Upgrade > Disc. Follow the instructions on the screen.
4 About 3 minutes later, the BDT will automatically turn off, when upgrade has been completed.
Read out the software version to confirm upgrade
1 Power on the BDT and press the “Settings” button on the remote.
2 Press left cursor on remote control to select "Information". The software version and other information will be displayed on the TV screen as follows:
Software Version: BDTX XX.XX.XX
Mac Address:XX-XX-XX-XX-XX-XX

Caution: The set must not be powered off during upgrading. Otherwise the Main board will be damaged entirely.
TROUBLESHOOTING
The player won’t power up (the Power indicator is not lit)  
* Check that the player’s Ac power cord is properly plugged into the player’s Power cord connector.
* Check that the player’s Ac power cord is plugged into a working Ac outlet and that the Ac outlet is not controlled by a switch.
* Make sure that the Master Power switch (on the player’s rear panel) is in the “On” position.
The disc does not play  
* Check that the disc is inserted correctly (label side up).
* Check that the disc is the correct type: Bd-video (single-layer or double-layer), DVD-VIDEO, DVD+R/+RW, DVD-R/-RW, CDDA (CD digital audio), CD-R/RW. Other disc types will not play.
No picture
* Check the connection between the player and the TV.
* Check that the Tv is turned on and that it is set to the correct input source.
* Confirm that all of the choices made in the display settings menu are correct for your TV.
* Check that the TV is HDCP-compliant. The player cannot be used with a TV that is not HDCP-compliant.
No sound
* Check that the HDMI and/or coaxial digital connections are properly made.
* If you’re using the coaxial digital connection, check that the digital audio settings on the connected device have been properly set.
* If you’re using only the HDMI connection, check that the HDMI audio settings on the connected device have been properly set.
* If you’re using only the HDMI connection, check that the BDT 3/BDT 30’s HDMI Audio Output is set to “On.”
The picture appears in the wrong aspect ratio
Change the Aspect Ratio setting in the display settings menu to match the TV.
There is noise or other interference in the picture while playing a Blu-ray disc recording or DVD.
Check that the disc surface is clean and not scratched.
Cannot access media on a connected USB device
Check that the device is formatted in the FAT-32 fie system. Other fie systems are not compatible with the BDT 3/BDT 30.
The player does not respond to remote-control commands.
* Replace both remote-control batteries with fresh ones, and make sure that they are installed correctly.
* Hold the remote control closer to the player.
* Check that the player’s remote sensor is in the remote control’s line of sight.
* Make sure that the protective shipping film has been removed from the player’s front panel.
The Ø symbol appears on the screen when you press a remote-control button 
The selected function is not permitted at the time you press the button.
The player does not respond to commands, or it behaves in an erratic way:
Unplug the player’s power cord from the Ac outlet, wait 30 seconds, and plug it back in.
SMPS SCHEMATIC & PWB
CLICK ON THE PICTURES TO MAGNIFY

PANASONIC TH-L32X10A LCD TV - HOW TO ENTER SERVICE MODE - SMPS SCHEMATIC

Power Supply Regulator Board Circuit Diagram _ Service Mode _ Universal Remote Control Set-up Codes_Panasonic TH-L32X10A LCD TV-LCD TV
SERVICE MODE
* While pressing [-/v] button of the main unit, press [INFO] button of the remote control three times within 3 seconds.
Key command
> “1” button...Main items Selection in forward direction
> “2” button...Main items Selection in reverse direction
> “3” button...Sub items Selection in forward direction
> “4” button...Sub items Selection in reverse direction
> “VOL” button...Value of sub items change in forward direction ( + ), in reverse direction ( - )
TO EXIT Service Mode - Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.
SMPS_BACK-LIGHT
Click on the pictures to Zoom In
Universal Remote Control set-up codes to check with Panasonic Brand TVs (CRT, LCD & Plasma models)
0016 0032 0033 0049 0054 0075 0099 0101 0104 0107 0110 0119 0143 0151 0152 0161 0166 0207 0249 0304 0305 0306 0396 0420 0461 0611 0631 0633 0692

PHILIPS 29PT6807 – Slim TV - SMPS – VERTICAL OUT – HORIZONTAL OUTPUT – VIDEO OUTPUT – SCHEMATIC

29PT6807 Philips – Slim TV -  SMPS – VERTICAL OUT – HORIZONTAL OUTPUT – VIDEO OUTPUT – SCHEMATIC (Circuit Diagram) 
Used ICs _ STR-W6556A_TDA4863AJ_TFA9843AJ(10W)_TFA9842AJ(6W)
SMPS [Power supply regulator] SCHEMATIC
VIDEO OUTPUT [CRT BASE CARD]
LINE DEFLECTION [HORIZONTAL SCAN OUTPUT]
FRAME DEFLECTION [VERTICAL SCAN OUTPUT]
AUDIO [SOUND] OUTPUT
CLICK ON THE SCHEMATICS TO MAGNIFY

Wednesday, December 17, 2014

harman-kardon - BDP 20/230 - BDP 2/120 - Blu-ray player - Power Supply (SMPS) _ Schematic

SMPS Circuit Diagram _ BDP 20/230 - BDP 2/120 - Blu-ray player - harman/kardon
SMPS SCHEMATIC
PWB
CLICK ON THE PICTURES TO MAGNIFY