TO ENTER SERVICE MODE
- While pressing the {Volume (-)} button on the Main Unit, press {INFO} button on the remote control 'Thrice' within "2" seconds. (Very fast action).
- Service mode will be displayed.
================================
SERVICE
ADJUST >> Picture adjustment
WB-ADJ >> White balance adjustment
OPTION >> Option setting
AGING >> Aging
RM-SET >> Remo control code adjustment
SRV-TOOL >> Service tool
=================================
Software version
-------------------------------------------------------------------
DTVSOC SOFT 1.3.39.34 RB Cnt 000
DTVSOC EEP 0.06.a9.30 PTCT 00 00 00 00 00
LSI DATA 00
STBY SOFT 0.46.00
STBY EEP ff ff ff
PDP SOFT 00.02
PDP EEP 58.42
PDP FPGA 10.04
PDP PDROM 58.22
-----------------------------------------------------------------
{PRESS "1" BUTTON]
====================================
ADJUST >> main item
CONTRAST >> sub-item 0000 >> data
YMAX
====================================
KEY COMMAND
[1] button > main items selection in forward direction.
[2] button > main items selection in reverse direction.
[3] button > sub items selection in forward direction.
[4] button > sub items selection in reverse direction.
[VOL] button > value of sub item change in forward direction (+), in revere direction ( - )
CONTENTS OF ADJUSTMENT MODE
- Value is shown as a hexadecimal number.
- Preset value differes depending on models.
- After entering the adjustment mode, take note of the value of each item before starting adjustment.
- To "EXIT", switch OFF the Power [Power button] on the Main Unit or the [Power] button on the remote control.
Main item
|
Sub item
|
Sample data
|
Remark
|
ADJUST
|
CONTRAST
|
46
|
|
COLOR
|
00
|
||
TINT
|
00
|
||
SUB BRIGHT
|
000
|
||
WB-ADJ
|
R CUT
|
80
|
|
G CUT
|
80
|
||
B CUT
|
80
|
||
R DRV
|
FC
|
||
B DRV
|
E8
|
||
ALL CUT
|
80
|
||
ALL DRV
|
FC
|
||
OPTION
|
BOOT
|
ROM
|
|
STBY SET
|
--
|
||
EMERGENCY
|
ON
| ||
CLK MODE
|
00
|
||
CLOCK
|
000
|
||
AGING
|
RGBW
|
||
VERTICAL LINE
|
|||
COUNT
|
|||
ALL WHITE
|
|||
ALL RED
|
|||
ALL GREEN
|
|||
ALL BLUE
|
|||
ON/OFF
|
|||
RAMP WHITE
|
|||
RAMP RED
|
|||
RAMP GREEN
|
|||
RAMP BLUE
|
|||
1% WINDOW
|
|||
COLOR BAR
|
|||
A-ZONE B-ZONE/4 TRIO
|
|||
SCROLL
|
|||
WHITE FLAME
|
|||
LOW SETUP RED
|
|||
LOW SETUP GREEN
|
|||
LOW SETUP BLUE
|
|||
RM-SET
|
CODE
|
A
|
FIXED
|
SRV TOOL --
|
---
|
SEE NEXT
|
SERVICE TOOL MODE
- Select [SRV-TOOL] in Service Mode.
- Press [OK] button on the remote control.
===========================================================
TD2Microcode:81c0000e => Display of TD2Microcode version.
Flash ROM : 1 - 227e => Display of Flash ROM maker code.
PTCT :00 : 00 : 00 : 00 => Display of SOS history
Time 00000:40 => Power-On time count {Press 'Mute' button} (3 sec)
===========================================================
DISPLAY OF SOS HISTORY
SOS HISTORY [Number of LED blinking indication]
- From left side; Last SOS, before last, three occurrence before, 2nd occurrence after shipment.
- This indication except 2nd and 1st occurrence after shipment will be cleared by {Self-Check indication and forced to factory shipment setting}
POWER ON TIME COUNT
- To display TIME/COUNT menu, highlight position, then press 'Mute' for '3' seconds.
- Time: Cumulative power ON time, indicated hour : minute by decimal.
- Count: Number of 'ON' times by decimal. [This indication will not be cleared by either of the self-checks or on any other command.]
- To 'EXIT' disconnect the AC cord from wall outlet.