The identification error within these Sony KV xxxxxx models is triggered in one of two ways. 1: Busy & 2:Device failure do not acknowledge IIC IC.
LED blinking codes: Failure to do so will report with a continuous flashing LED.
ERROR MESSAGE
|
Error message
|
LED Blinking Code
|
|
No error
|
00
|
|
Reserved
|
01
|
|
OCP [Over Current Protection]
|
02
|
|
Over Voltage Protection [OVP]
|
03
|
|
Failure to vertical Sync:
|
04
|
|
IKR error at Power On
|
05
|
|
IIC bus clock and | or data lines low at Power On
|
06
|
|
NVM no IIC bus knowledge at Power On
|
07
|
|
Horizontal Protection; including Line Output Transformer
and | Transistor
|
08
|
|
Tuner no acknowledgment at Power On
|
09
|
|
Sound processor error
|
10
|
|
reserved
|
11
|
|
Scan rate error
|
12
|
|
DAC error
|
13
|
|
Back end error
|
14
|
|
Dynamic convergence error
|
15
|
|
PIP error
|
16
|
TABLE-2
To enter Table-2
- Turn ON the main Power Switch of the tV set.
- Program remote control for Operation in service mode.
- Press {Video => Video => Menu} on the remote control.
- Using remote control, scroll to the Error Menu item using the 'Dn' arrow key, and press ( > ) arrow key.
- The following table will be displayed.
|
|
ERROR MENU
|
|
|
|
E02
|
OCP
|
0,255
|
0
|
|
E03
|
OVP
|
0,255
|
0
|
|
E04
|
VSYNC
|
0,255
|
0
|
|
E06
|
IIC
|
0,255
|
0
|
|
E07
|
NVM
|
0,255
|
0
|
|
E08
|
HPROT
|
0,255
|
0
|
|
E09
|
TUNER
|
0,255
|
0
|
|
E10
|
SOUNDP
|
0,255
|
0
|
|
E11
|
----
|
0,255
|
0
|
|
E12
|
SCANRATE
|
0,255
|
0
|
|
E13
|
DAC
|
0,255
|
0
|
|
E14
|
BACKEND
|
0,255
|
0
|
|
E15
|
DYN CON
|
0,255
|
0
|
|
E16
|
PIP
|
0,255
|
0
|
|
|
|
|
|
|
|
|
|
|
|
WORKING TIME
|
|
|
|
|
HOURS
|
|
|
14
|
|
MINUTES
|
|
|
7
|
SERVICE MODE
Service adjustments to these model Sony TVs can be performed using Remote Control Model [RM-932]
- Press VCR | TV | DVD button until the TV LED lights.
- Press and Hold "YELLOW" button for ~ 5 seconds, until the TV LED Flashes Quickly.
- Press {99999}. All three LEDs should light. The remote control is now Set to Service Mode.
- To return the remote control to normal operation, ie, to Exit Service Mode, repeat steps [1] & [2], then press {00000}. All LEDs should light. The remote control is now set to Normal Mode.
SETTING TV INTO SERVICE MODE
- Program the remote control for operation in service mode as described above.
- Turn ON the TV main Power Switch.
- Press the 'Video Standby button" on the remote control, Twice. "TT____" will appear in the upper right corner of the screen. Other Status Information will also be displayed.
- Press 'Menu' button on the remote control to obtain the following Menu on the screen.
|
Geometry
|
|
Service
|
|
Scanrate
|
|
Dyn. Cinv
|
|
PiP
|
|
Sound
|
|
IF adjust
|
|
Error menu
|
|
|
|
AE6B v0.14 (Jun 2001)
|
|
Factory data
FFh FFh
|
|
MSP device:
MSP3411G
|
|
|
6. Press the ( > ) button to enter into the required Menu Item.
7. Press 'Menu' button on the remote control to Quit "Service Mode".
|
|
GEOMETRY
|
|
|
ABL TH
|
0,3
|
0
|
|
ABL MODE
|
0,3
|
0
|
|
P ABL
|
0,15
|
15
|
|
V SIZE
|
0,63
|
35
|
|
V POSITION
|
0,63
|
33
|
|
V COMP
|
0,3
|
1
|
|
V LIN
|
0,15
|
7
|
|
S-CORRECTION
|
0,15
|
7
|
|
H SIZE
|
0,63
|
44
|
|
PIN AMP
|
0,63
|
32
|
|
UP CORNER PIN
|
0,63
|
29
|
|
M PIN
|
0,3
|
2
|
|
LO CORNER PIN
|
0,63
|
29
|
|
TRAPEZIUM
|
0,15
|
2
|
|
H POSITION
|
0,63
|
40
|
|
AFC BOW
|
0,15
|
8
|
|
AFC ANGLE
|
0,15
|
9
|
|
LEFT BLK
|
0,63
|
34
|
|
RIGHT BLK
|
0,63
|
17
|
|
V ASPECT
|
0,63
|
47
|
|
AKBTIM1
|
0,3
|
2
|
|
AKBTIM2
|
0,1
|
0
|
|
IKR
|
|
1
|
|
HNG
|
|
0
|
|
VNG
|
|
0
|
|
|
|
|
No comments:
Post a Comment