LG 32FS4RNP 32FS4RNP-LE _ ADJUSTMENTS

ADJUSTMENTS
Preliminary Steps

• Turn on the TV set.
• The equipment must be operated for about 15 minutes prior to adjustment.

Adjustment

• Set the RF signal without condition or after receiving a signal.
• Press the ADJ button on the Remote Control to enter the Screen Mode to create a horizontal line.  Turn the Volume screen to not display the horizontal line and rotate clockwise so that it can be viewed.

Set White Balance

• Perform pre-screen settings (screen).
• As the sequence below, you can adjust it manually.

Test Equipment

• White Balance Auto Meter (which can generate standards High or Low Brightness): automatic adjustment.
• Gauge White Balance (CRT color analyzer, CA-100).
• Remote control for adjustment.

Tune the TV to receive a 100% white pattern.

Perform advance settings screen (Screen).

• The White Balance should be adjusted by the meter white balance or the remote.
• Press ADJ to enter the adjustment mode, search the RGB mode W-B with the CH [UP],  and CH [DN] select by pressing VOL.
• Adjust the item using the buttons CH[UP], CH[DN]
• Adjust the data via the  keys VOL[LEFT], VOL[RIGHT].

1. Adjust "CONTRAST" and "BRIGHT" until the level of brightness is 35Ft_L.
2. Select the RD (R-DRIVE) and set the Y coordinate in High brightness and select BD (B-DRIVE) and adjust the X coordinated so that the color coordinates High
3. Set the "CONTRAST" and "BRIGHT" so that the level Brightness is 4.5 Ft_L.
4. Select the RC (R-CUTOFF) and set the Y coordinate Lower brightness and select BC (B-CUTOFF) and setting the coordinate X so that the coordinates the color having low brightness values
5. Repeat steps 1) ~ 4) to obtain the coordinates of colors that satisfy] for high and low luminosity.
6. Check the color coordinates adjusted using a meter of white balance.

Data Set Deflection

Set Deflection data through Remote Control.

The receive TV signal.

The setting sequence is based on the setting and 3Mode initial adjustment will be made based on the NTSC mode.

1. Sequence: NTSC => PAL (100Hz) => PAL (50p)
2. After adjustment 100Hz PAL, press the Mode remote control and adjust the 50P (50Hz Progressive).
3. Enter the adjustment mode: Click the ADJ key => Mode adjustment SVC => Click 0.deflection.
4.  Select the adjustment items through CH [UP/DN]
5. Adjust the data through the VOL[LEFT/RIGHT]

Set (29 ")

• VL (Vertical Linearity)  Adjust the top & bottom size of inner circle to be equal.
• VS (Vertical Shift)  Adjust so that the horizontal center line of the circular pattern digital conforms to the geometric center horizontal CPT.
• VA (Vertical Amplitude)  Adjust the upper and lower circle effective screen CPT to stay at a distance of 6 ~ 7mm.
• SC (Vertical S Correction)  Adjust the widths of latitudes Superior / Central / Lower they are the same.  As the value determined by TLC DY used, set as standard for use of CPT.
• HS (Horizontal Shift)  Adjust so that the vertical center line of the circular digital pattern conforms to the geometric center of the vertical CPT.
• EW (East-West Width)  Adjust the ends of latitudes left / right to be united with the effective surface of the edge of the CPT.
•  BOW (Bow) Adjust line, do not change the default value.
• ANG:  In setting angle, the tilt adjustment until the line central vertical is precisely vertical.
•  EP (Parable east-west)  Adjust so that the middle portion of the left vertical line and right rein ends with parallel lines Vertical CPT.
•  CRNU (Correction Corner Higher)  After completing the EP adjustment, adjust until the vertical line the upper-left and upper-right are aligned.
• CRNL (Correction of Lower Corner)  After completing the EP adjustment, adjust until the vertical line the bottom-left and bottom-right are aligned.
• CRNU6:  After finishing the setting CRNU, adjust the vertical line top-left and top-right of the screen for that become aligned as possible.
• CRNL6:  After finishing the setting CRNL, adjust the vertical line top-left and top-right of the screen for that become aligned as possible.  # After making the above adjustments, readjust PINAHAS Size H, PINAMP, AFCANGL, AFCBOW UPCPIN and to LOCPIN completing the adjustment pin cushion.
•  After finishing the setting, move to "Store All Mode" and press the "OK" to save changes made.

1. "Store All Mode" works only in setting mode home, and if the "OK" button is pressed after the fit into another input signal, it saves the data adjusted accordingly.
2.  "Store All Mode" stores the values ​​adjusted otherwise input signal being based on data the initial set mode. (use this for initial setting production)
3. "This Store Mode" store the setting values ​​of Correspondingly without otherwise relate input signal.

•  After finishing the setting in the initial mode, apply the adjustment checking the status of the setting of another input signal.

PAL (100Hz): All Mode Store

PAL (50p): This Store Mode

NTSC: This Store Mode

Set (32 ")

• VS (Vertical Shift)  Adjust so that the horizontal center line of the circular pattern digital conforms to the geometric center horizontal CPT.
• VA (Vertical Amplitude) & U-VL, L-VL Adjust the upper and lower circle effective screen CPT to stay at a distance of 6 ~ 7mm.  A para adjustment (U-VL) & (VL-L), setting up the largest Digital Pattern inscribed circle coincides with the frame external screen.

Set (32 ")

• HS (Horizontal Shift)  Adjust so that the vertical center line of the circular pattern digital conforms to the geometric center vertical CPT.
• EW (East-West Width)  Adjust the ends of latitudes left / right to be united with the effective surface of the edge of the CPT.
• BOW:  The base does not change the default value adjustment line.  (It will be necessary when the portion is above or below deflected to the left or right by diverting DY)
• A-ANG:  In setting angle, the tilt adjustment until the line central vertical is precisely vertical.
• EPP:  Adjust so that the upper and lower horizontal width are identical.
• EP (Parable east-west)  Adjust so that the middle portion of the left vertical line and right most extreme beam parallel to the lines Vertical CPT.
• UC (Pincution Corner Higher)  After finishing the setting PINAMP, make adjustments until the vertical lines on the top left and right are aligned.
• LC (Pincution Corner Bottom)  After finishing the setting PINAMP, make adjustments until the vertical lines on the bottom left and right are aligned.
• V-SCR (V-SCROLL)  Perform this adjustment only when it is impossible to make the V Shift adjustment.
• SC (Vertical S Correction)  Adjust the widths of latitudes Superior / Central / Lower they are identical.  As the value determined by TLC DY used, set as standard for use of CPT.
• After finishing the setting, move to "Store All Mode" and press the "OK" button to save the changes.

1. "Store All Mode" works only in setting mode home, and if the "OK" button is pressed after adjusting another input signal, it saves the adjusted data the corresponding mode.
2. “ Store All Mode" stores the values ​​of another set mode input signal being based on data mode initial setting. (use this to adjust the initial production)
3. "This Store Mode" stores the values ​​for mode setting without corresponding relate otherwise signal input.

After finishing the setting in the initial mode, apply the adjustment checking the status of the setting of another input signal.

NTSC: All Mode Store

PAL (100Hz): This Store Mode

PAL (50p): This Store Mode.