PHILIPS - LC4.1E CHASSIS - LCD TVs - ERROR CODES - LED BLINKING CODES & DETAILS - Universal Remote Control Set-up Codes

ERROR CODES

  The error code buffer contains all errors detected since the last time the buffer was erased. The buffer is written from left to right. When an error occurs that is not yet in the error code buffer, it is displayed at the left side and all other errors shift one position to the right.

HOW TO READ ERROR CODES

On screen via the SAM (if you have a picture).

Examples:

ERROR: 0 0 0 0 0 : No errors detected

ERROR: 6 0 0 0 0 : Error code 6 is the last and only detected error.

ERROR: 9 6 0 0 0 : Error code 6 was detected first and error code 9 is the last detected (newest) error

Via the blinking LED procedure (when you have no picture).

Via ComPair.

TO CLEAR ERROR BUFFER

By using the CLEAR command in the SAM menu: [to know more about SAM menu, check the previous post here]

• To enter SAM, press the following key sequence on the remote control transmitter: “062596” directly followed by the OSD/STATUS button (do not allow the display to time out between entries while keying the sequence).
• Make sure the menu item CLEAR is highlighted. Use the MENU UP/DOWN buttons, if necessary.
• Press the MENU RIGHT button to clear the error buffer. The text on the right side of the “CLEAR” line will change from “CLEAR?” to “CLEARED”
• If the contents of the error buffer have not changed for 50 hours, the error buffer resets automatically.

Note: If you exit SAM by disconnecting the mains from the television set, the error buffer is not reset.

ERROR CODES

In case of non-intermittent faults, write down the errors present in the error buffer and clear the error buffer before you begin the repair. This ensures that old error codes are no longer present.  If possible, check the entire contents of the error buffer. In some situations, an error code is only the result of another error and not the actual cause of the problem (for example, a fault in the protection detection circuitry can also lead to a protection).

Error	Device	Error description	Check item
0	Not applicable
1	Not applicable
2	Not applicable
3	Not applicable
4	GM5221	I2C error while communicating with the Genesis Scaler and/or Flash-ROM is faulty/empty	7401 7403
5	Not applicable	+5v protection	7930
6	i2C bus	General I2C error	7011, 3083, 3084
7	Not applicable
8	M24C32	I2C error while communicating with the Scaler EEPROM	7402
9	M24C16	I2C error while communicating with the EEPROM	7099
10	Tuner	I2C error while communicating with the PLL tuner	1302, 3302, 3303, 3327
11	Not applicable
12	Not applicable
13	Not applicable

LED BLINKING PROCEDURE

When the SDM is entered, the front LED will blink the contents of the error-buffer:

• The Led blinks with as many pulses as the error code number, followed by a time period of 1.5 seconds, in which the Led is off.
• Then this sequence starts is repeated.  Any RC5 command terminates this sequence.

Example of error buffer: 12 9 6 0 0

After entering SDM, the following occurs:

• 1 long blink of 5 seconds to start the sequence,
• 12 short blinks followed by a pause of 1.5 seconds.
• 9 short blinks followed by a pause of 1.5 seconds,
• 6 short blinks followed by a pause of 1.5 seconds,
• 1 long blink of 1.5 seconds to finish the sequence,
• The sequence starts again at 12 short blinks.

Universal Remote Control Set-up codes
11454, 10054, 10690, 11744, 11867
1049 1132 1232 1057 1374 1365 1366 1415 1144 1206 1364 1317 1287 1194 1289 1142 1008 1383 1061 1051 1278 1262 1130 1233 1172 1053 1380 1046 1027 1053 1054 1350 1160 1155 1298 1025 1231 1238 1481 0062 0204 0184 0208 0205 0206 0207 0004 0189 0183 0199 0200 0288 0456 0003 0008 0068 0075 0086 0087 0141 1002, 1009, 1014, 1036, 1051, 1056, 1060, 1061, 1066, 1067,1072, 1073, 1074, 1077, 1078, 1082, 1086, 1136, 1152, 1156, 1166, 1174, 1175, 1180, 1181
011, 012, 013, 119, 025, 030, 031, 032, 471, 479, 485, 490, 491, 492,075,081,082,087,088,090,196,197, 016,017,019,021,022,025,075,081,082,087,088,089,099,100,101,102