On occasion, Playback may stop, or No Play occurs, when a
particular DVD title is used. For example, The Man Who Fell To Earth",
"The Matrix".The SYSCON ROM should be upgraded to Version 1.8. The
description below is another DVD title that has this problem. Autoflaggthe
Sycon Rom if it is not Version 1.8. If units require the SYSCON upgrade, then
upgrade is done as in warranty, regardless of warranty status.
This symptom occurs when the DVD has played more than 7
minutes and before 27 minutes and 57 seconds. This countermeasure may apply to
other titles not listed.
Solution: Replace IC 093 on the MB-80 or MB-75 board
depending on model.
INTERMITTENT SOUND: SYMPTOM (257)
CASE 1:When DVD or Video CD playback is selected, line audio
output and digital audio output may have intermittent sound. When in CD mode
there is no problem.
CASE 2: When using a Kenwood Amp in DVD, Video CD, or CD playback,
the digital audio output may have intermittent sound. The line audio
output in this case will be normal.
Solution:
CASE 1: Replace IC 380 with CXD8603BR on the MB-75 board.
CASE 2: Make sure that the digital audio cable does not have
a problem. If the cable is good, and the DVP-S7000 is good, the problem could be the Kenwood Amp.
COLOR NOT LOCKING
The color lock may become intermittent. After a few minutes
of DVD play, the colors may start to change. If the symptom is appearing, check
the following.
- Connect an Oscilloscope probe to TP021. If the waveform is not phaselocked, X003 is defective.
- If the symptom is not appearing, you still should check 27MHz free run frequency adjustment.
IC SOLDER CONNECTIONS
The MB-80 board may be using the new soldering technique as
illustrated in the picture below. This is actually an improvement to prevent
solder bridges between the fine-pitched IC leads. Please note that intermittent
solder connections can happen, particularly on IC312.
Solution: If you are experiencing no DVD play, it may be
caused by intermittent solder connections on IC312. Re-solder the IC carefully
then retest the unit.
DVD DISC WILL NOT PLAY
When the DVD dual layer disc does not want to play
Solution: Confirm the following:
- No damage or fingerprints are on the DVD disc.
- Check the RF Level of the optical pick-up using the reference DISC HLX-503.Be in playback mode, and then check the RF Level. The RF Level can be probed at test point TP891 on the MB-75 Board. If the output of the optical is not within specs, replace it.
BOARD CHANGE [TT-40]
Symptom: (xxxx)
The DVP-S7000 TT-701 board is being changed to a TT-40
board. The TT-40 board is already used in the DVP-S3000. Some resistors need to
be changed to make the new TT-40 board compatible with a DVPS-3000 or a
DVPS-7000.
Solution: Order the TT-40 below the 0-Ohm resistor is also
shown below.
To make the TT-40 board compatible for the DVPS-3000, or
DVPS7000, check the following and modify if necessary. Use the chart below for
the A-6065-062-A TT-40 Board.
DRIVE AUTO ADJUSTMENT ERRORS
When in service test mode, the drive auto adjustment may
report errors.
This may happen when you select 0: ALL.
When the unit asks for the DL test disk you may see an error
when the test is running.
Solution:
Run the adjustment again and select each type of disc
individually.
Select SL, CD, and DL one at a time ,and proceed with drive
auto adjustment.
SYSTEM CONTROL VERSION UPGRADE
Occasionally distorted noise may be present at the start and
throughout DVD playback. This distortion may be present on 5.1 output as well
as analog audio output. Also block error noise can be seen if you hit pause,
then playback. If Video CD is played, the menu may not be displayed.
Solution: Replace the
ROM of the system control micro IC803 with new version V 1.8. The ROM is on the
MB-78 board.
NO DUAL LAYER DVD PLAY
Verify following IC140 versions, using Diagnostics Test Mode
Menu (Other Checks). If the DRVCon is not updated to latest version, replace
IC140 as per the table below. Be sure to do the auto drive
alignments after the IC140 is replaced. If the units are being repaired for the
dual layer issue only, then service is done as in warranty status. Verify the
repair by testing unit with a commercial Dual Layer DVD.
NOTE:
DVP-S7000: R926, R927 should be zero ohms, R140should be
open.
DVP-S3000: Only IC140 need to be replaced.
Applicable Serial Number Range: DVP-S7000 up to 845295 DVP-S3000
all units.
CLICK NOISE PRESENT WITH AUDIO DIGITAL CONNECTION
When playing a DVD disc, noise may present when pressing
function buttons, for example NEXT/PREV. This noise may be heard when an
Optical/Coaxial connection is made to the AC-3 Decoder. If the symptom appears
then do the following.
Solution: Replace the SYSCON ROM IC803 and the A/V DECODER
(IC203) new version. These IC are located on the MB-78 board.
For IC803, ICMSM27C802CZ-P02GS-KDR1 (8-759-579-58) (Ver 2.3)
can also be used.
WHEN PLAYING DUAL LAYER DVD UNIT PAUSES OR STOPS
When playing DUAL LAYER DVD’s, the unit may pause, or stop
playing the disc. This may happen when DVD playback is switching from Layer 0
to Layer
An error code of C13:92, may also be displayed.
Solution: Verify the following IC803 version numbers
depending on models. If the SYSCON IC803 is not current version, replace
regardless. If Out of Warranty units are being serviced for the DUAL LAYER
SWITCHING only, then service is done as in-warranty status.
CLICK ON PICTURES TO ZOOM