BUSH BTV17, GOODMANS GTV371VCR, Orion CTV, Sharewood AX4050R - service mode adjustments and schematic- STR G6653 based SMPS

To enter SERVICE MODE, unplug AC cord till lost actual clock time. Then press and hold Vol (-) button of main unit and remocon key simultaneously.
The both pressing of set key and remote control key will not be possible if clock has been set. 

To reset clock, either unplug AC cord and allow at least 30 minutes before Power On or alternatively, discharge backup capacitor.

CONFIRMATION OF USING HOURS.
POWER ON total hours and PLAY/REC total hours can be checked on the screen.
Total hours are displayed in 16 system of notation.
NOTE: The confirmation of using hours will not be possible if clock has been set. To reset clock, either unplug AC cord and allow at least 30 minutes before Power On or alternatively, discharge backup capacitor.
Set the VOLUME to minimum.
Press both VOL. DOWN button on the set and the Channel button (6) on the remote control simultaneously.
After the confirmation of using hours, turn off the power.

[(16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value)]

On-Screen Display Adjustment.
Unplug the AC plug for more than 30 minutes to set the clock to the non-setting state. Then, set the volume level to minimum.
Press the VOL. DOWN button on the set and the channel button (9) on the remote control simultaneously to display adjustment mode on the screen.

Use the channel buttons (1-8) on the remote control to select the options.

Press the channel button (0) on the remote control to end the adjustments.

VCR SECTION PG SHIFTER.
Connect CH-1 on the oscilloscope to TP4001 and CH-2 to TP4501.
Playback the alignment tape. (JG001C)
Press and hold the Tracking-Auto button on the remote control more than 2 seconds to set tracking to center.
Press the VOL. DOWN button on the set and the channel button (3) on the remote control simultaneously until the indicator REC disappears. 

If the indicator REC disappears, adjustment is completed.

(If the above adjustments doesn't work well go with this procedure.)
Press the VOL. DOWN button on the set and the channel button (3) on the remote control simultaneously until the indicator REC disappears.
When the REC indicator is blinking, press both VOL. DOWN button on the set and the channel button (4) on the remote control simultaneously and adjust the Tracking +/- button until the arising to the down of Head Switching Pulse becomes 6.5 +/-- 0.5H.

Press the Tracking Auto button.

RF AGC DELAY.

Receive the monoscope pattern.
Connect the digital voltmeter between the pin 5 of CP603 and the pin 1 (GND) of CP603.

Activate the adjustment mode display of  and press the channel button (5) on the remote control.
The appears on the display.
Press the channel button (1) on the remote control to select "RF AGC DELAY".
Press the VOL. UP/DOWN button on the remote control until the digital voltmeter is 2.50 +/-- 0.05V (80dB).

VCO FREERUN.

Connect the oscillator to pin 11 of TU601.
Connect the digital voltmeter to pin 47 of IC601.
Adjust the L608 until the digital voltmeter is 3.6 +/-- 0.05V.

(TV SECTION) CONSTANT VOLTAGE (AC)

Using the remote control, set the brightness and contrast to normal position.
Connect the digital voltmeter to TP401.
Set condition is AV MODE without signal.
Adjust the VR502 until the DC voltage is DC 130 +/-- 0.5V.

CONSTANT VOLTAGE (DC).

Using the remote control, set the brightness and contrast to normal position.
Connect the digital voltmeter to TP401.
Set condition is AV MODE without signal.
Adjust the VR501 until the DC voltage is DC 130 +/-- 0.5V.

CUT OFF.

Place the set with Aging Test for more than 15 minutes.
Set condition is AV MODE without signal.
Using the remote control, set the brightness and contrast to normal position.
Activate the adjustment mode display  and press the channel button (5) on the remote control.
The settings appears on the display.
Press the channel button (5) on the remote control to select "CUT OFF".
Adjust the Screen Volume until a dim raster is obtained.

FOCUS.

Receive the monoscope pattern.
Using the remote control, set the brightness and contrast to normal position.
Turn the Focus Volume fully counterclockwise once.
Adjust the Focus Volume until picture is distinct. This adjustment is the same for all CRT TVs, irrespective of it's brand and screen size.

WHITE BALANCE.

NOTE: Adjust after performing CUT OFF adjustments before this adjustment.

Place the set with Aging Test for more than 15 minutes.

Receive the white 100% signal from the Pattern Generator.
Using the remote control, set the brightness and contrast
to normal position.
Activate the adjustment mode display and press the channel button (2) on the remote control to select "AKB".  

Press the channel button (2) on the remote control to select the "R.BIAS".
Using the SET +/- keys on the remote control, adjust the R.BIAS.
Press the CH. UP/DOWN button on the remote control to select the "G.BIAS", "B.BIAS", "R.DRIVE" or "B.DRIVE".
Using the SET +/- keys on the remote control, adjust the G.BIAS, B.BIAS, R.DRIVE or B.DRIVE.
Perform the above adjustment 7 and 8 until the white color is looked like a white.

SUB BRIGHTNESS.

Receive the monoscope pattern. (RF Input)
Using the remote control, set the brightness and contrast to normal position.
Activate the adjustment mode display and press the channel button (4) on the remote control.
Press the channel button (1) on the remote control to select "BRIGHT".
Press the VOL. UP/DOWN button on the remote control until the white 25% is starting to be visible.
Receive the monoscope pattern. (Audio Video Input).
Press the AV button on the remote control to set to the AV mode. Then perform the above adjustments 2~5.

SUB COLOR.

Receive the color bar pattern. (RF Input)
Connect the synchro scope to TP801.
Using the remote control, set the brightness, contrast and color to normal position.
Activate the adjustment mode display and press the channel button (4) on the remote control.
Press the channel button (3) on the remote control to select "COLOR".
Adjust the VOLTS RANGE VARIABLE knob of the oscilloscope until the range between white 100% and 0% is set to 4 divisions on the screen of the oscilloscope.
Press the VOL. UP/DOWN button on the remote control until the red level is set to the 4 divisions.
Receive the rainbow pattern. (Audio Video Input)
Press the AV button on the remote control to set to the AV mode. Then perform the above adjustments 2~7.

HORIZONTAL PHASE.

Receive the monoscope pattern.
Using the remote control, set the brightness and contrast to normal position.
Activate the adjustment mode display and press the channel button (1) on the remote control.
Press the channel button (1) on the remote control to select "H. PHASE".
Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on right and left becomes minimum.

VERTICAL SIZE.

Receive the monoscope pattern.
Using the remote control, set the brightness and contrast to normal position.
Activate the adjustment mode display and press the channel button (1) on the remote control.
Press the channel button (3) on the remote control to select "V. SIZE".
Press the VOL. UP/DOWN button on the remote control until the horizontal over scan is equal to the vertical over scan.

VERTICAL LINEARITY.

Receive the monoscope pattern.
Using the remote control, set the brightness and contrast to normal position.
Activate the adjustment mode display and press the channel button (1) on the remote control.
Press the channel button (5) on the remote control to select "V. LIN".
Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on upside and downside becomes minimum.
VERTICAL POSITION.

Receive the monoscope pattern.
Using the remote control, set the brightness and contrast to normal position.
Activate the adjustment mode and press the channel button (1) on the remote control.
Press the channel button (4) on the remote control to select "V. POSI".
Press the VOL. UP/DOWN button on the remote control until the horizontal line of the monoscope comes to approximate center of the CRT.

OSD HORIZONTAL.

Receive monoscope pattern.
Using the remote control, set the brightness and contrast to normal position.
Activate the adjustment mode display  and press the channel button (5) on the remote control.
Press the channel button (4) on the remote control to select "OSD H".
Press the VOL. UP/DOWN button on the remote control until the difference of A and B becomes minimum.

VERTICAL LINEARITY 60 (AV).

Receive the monoscope pattern (Audio Video Input).
Using the remote control, set the brightness and contrast to normal position.
Activate the adjustment mode display and press the channel button (1) on the remote control.
Press the channel button (5) on the remote control to select "V. LIN".
Press the VOL. UP/DOWN button on the remote control until the horizontal line of the color bar comes to approximate center of the CRT.

Schematic- TV Power [SMPS] – STR-F6707 based.

Schematic – Deflection.

Schematic-chroma LA76812.

SYSCON SCHEMATIC.

TV power – STRG6653 based.

Interconnection diagram.

REPLACING THE MEMORY IC.
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to TABLE below.

Enter DATA SET mode by setting VOLUME to minimum.

While holding down VOLUME button on front cabinet, press key 6 on remote control simultaneously.
ADDRESS and DATA should appear as FIG below.

ADDRESS is now selected and should "blink". Using the SET + or - keys on the remote, step through the
ADDRESS until required ADDRESS to be changed is reached.
Press ENTER to select DATA. When DATA is selected, it will "blink".
Again, step through the DATA using SET + or - until required DATA value has been selected.
Pressing ENTER will take you back to ADDRESS for further selection if necessary.
Repeat steps 3 to 6 until all data has been checked.
When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.

The unit will now have the correct DATA for the new MEMORY IC.

LG 29 inch CRT TV – How to enter the service mode, service adjustments, Option settings, full schematic – MC-991A chassis

System control IC:

LG8993-16B(CXP86441-567S) *ASIA.

LG8993-21A(CXP86441-569S) *ASIA.

LG8993-24A(CXP86441-571S) *EU.

TDA4474A,TEA5114, MC14577, ST24C16, TDA4566, TDA4665, TDA8395, TDA8376, MSP3410, TDA2616, CXA2040AQ, TDA4474A, CXD2064Q, LA7845, TDA61O8JF, SE115, SAA5261, GL4558, STR-S6709, SE115, PC123A [optocoupler], 24C04, 6174Z-6005D [SMPS transformer], 151-A10Z [LOT]

Service mode

Press OK buttons on both TV set and Remote Controller at the same time to get into SVC mode.

Deflection Data Adjustment (Line SVC-1)

1. At SVC mode, press the Yellow colored button.  

If the Remote Controller doesn't have the Yellow button, use the button under the Channel Down(PR U) button.
And then, deflection data adjustment OSD (SVC1 mode) will be displayed.
2) Press Channel UP/DOWN button for desirous function Adjustment.
3) Press Volume UP/DOWN button to adjust the data.

VL--(Vertical Linearity)
Adjust so that the boundary line between upper and lower half is in accord with geometric horizontal center of the CPT.
VH--(Vertical Height)
Adjust so that the circle of a digital circle pattern may be located within the effective screen of the CPT.
SC--(Vertical "S" correction)
Adjust so that all distance between each horizontal lines are to be the same.
VS--(Vertical Shift)
Adjust so that the horizontal center line of a digital circle pattern is in accord with geometric horizontal center of the CPT.
HS--(Horizontal Shift)
Adjust so that the vertical center line of a digital circle pattern is in accord with geometric vertical center of the CPT.
EW--(Horizontal Width)
Adjust to that a digital circle pattern looks like exact circle.
EP--(East-west Parabola)
Adjust so that middle portion of the outermost left and right vertical line looks like parallel with vertical lines of the CPT.
EC--(East-west Corner)
Adjust so that the vertical line at every 4 corners of the screen looks like parallel with the vertical lines of the CPT.
ET--(East-west Trapezium)
Adjust to make the length of top horizontal line same with it of the bottom horizontal line.

Hold Down Check(X-ray Protection)
1) Short the both terminal of R430 on the Main2 Board and check if the TV set turns into Stand-by,  It should.

White Balance Adjustment.(LINE SVC 0)
NOTE : This adjustment should be performed after screen voltage adjustment.
1) Tune the TV set to receive an 100% white pattern.
2) Press the Yellow button on remote controller in the SVC Mode (press OK buttons on both TV set and remote controller at the same time) then you can find On Screen Display.
3) Press PSM (RED) button on remote controller. (Standard picture)
4) Press PR+ or PR- button for desirous function adjustment.
5) Adjust VOL+ or VOL- button for Gg31.
6) Adjust VOL+ or VOL-button in each status of "Rg--"/"Bg--" for X=272.8, Y=295.8 with color analyzer (color temperature 11,000oK).

OPTION Adjustment (SVC MODE:OPTION-1, OPTION-2, OPTION-3)
NOTE: When the EEPROM has been replaced, the Option data should be restored as the function of individual system and specification.
1) Press OK buttons on both TV set and Remote Controller at the same time to get into SVC mode.
2) Press the Yellow button several times to find OPTION-1, OPTION-2 and OPTION-3.
3) Input the correspond OPTION data referring to Table below with the numeric buttons 0~9.

Sound Pre scaler
1) Set to Scart when one of AV1 or AV2 is Scart jack.  Audio out level : 500mVrms at 54% modulation ratio
2) Set to Phono when both of AV1 and AV2 is RCA Phono jack.  Audio out level : 500mVrms at 100% modulation ratio.
(NTSC-M : 400mVrms)

MSP3410(3400) Pre-scaler setting

Schematic

Samsung UA43RU7100 – Service mode – power board troubleshooting

Samsung 43,50,55,58,65 and 75 inch LCD TV power board and back-light inverter troubleshooting

Applicable to UA43RU7100K, UA50RU7100K, UA55RU7100K, UA58RU7100K, UA65RU7100K, UA75RU7100K

Function Control Operation Test

1. Place TV in Power Standby
2. Check LED Status
3. If LED is OFF:

LED 1.7Vdc (pin 8 ) and VCC for 3.3Vdc (pin 3 )

If missing suspect Function Assy/Cable/Main board.

4. If LED is ON:

Switch Operation activates on screen display

If missing:

Key_Input 1 (pin 6 ) change to 0V with a command.

If wrong voltage or no change:

Switch for stuck or miss-operation.

5. Check IR operation with Standard Remote command changes.
6. Check SDA, SCL for effective 3.3Vdc. (after power on)
If missing suspect Function Assy/Cable Assy./Main Assy

Power: SMPS Standby: 43 inches – connector voltages.

50/55/58 inches SMPS connector voltages.

65 inches SMPS connector voltages.

75 inches SMPS connector voltages.

TV power standby test.

1. TV in Standby
 Check Standby LED Indicator.
2. If Not Lit:
 Check AC 120Vac Line.
3. If missing:
 Check AC120Vac Source/Power Cord.
4. If OK:
 Check resistance on SMPS FUSE after first removing AC power cord.
5. If fuse/s are open : replace SMPS.

6. If fus are OK:

  Standby: A13V (Always On) to Main Board.
7. If any missing remove the SMPS connector to the Main Board.
9 Check Standby A13V again.
 If OK replace the Main Board.
 If still missing replace SMPS.

SMPS Power On: 43 inches.

SMPS Power ON: 50/55/58 inches.

SMPS power ON: 65 inches.

SMPS Power ON: 75 inches.

Power ON sequence test.

1. Power TV On.
 Power_On/Off / POWER_ON (pin 8 ) 0.2Vdc (when off) changes to 3.3Vdc (on). [There is an approx 20 second delay from PS-ON to off condition when the TV is powered off, and approx a 2 minute delay when the TV is first plugged into AC Power]

2. If voltage error or no change:

9 Jog Function Control Test.
3. If OK replace Main Board.
9 All A13V supplies for approx. 12.7VDC (pins 3 , 5 , 7 , 9 )
4. If any wrong voltages, remove SMPS connector to Main Board.
9 All A13V again for 12.7VDC (pins 3 , 5 , 7 , 9 )
5. If OK replace Main Board.
6. If still wrong voltage replace SMPS.

    9 OD_ON/OFF (Over Voltage Detect) (pin 4 ) 3.3Vdc : Operating Normal.

7. If 0V or changing, an SMPS or Panel error exists. Perform Backlight Test.
9 BLU_PWM / PWM_BLU (pin 6 ) Backlight On/Off & Dim Control : 1Vdc – 3.3 Vdc depending on backlight dimming level for video.
• If missing or error : Replace Main Board.

SMPS / PANEL BACKLIGHT (Parallel Wired SMPS Panel Connections)

43, 50, 55, & 58 inches

65 and 75 inches.

Backlight Test :
1. Activate Backlights Test : Disconnect Lead Cable from Main to Power Supply.
 Check TV Screen for active backlight LEDs.
2. If No Backlight.
 Minus (Control) pins & Plus (Supply) pins voltages on the Panel Connector. (with fine test probe on left side of connector only for safety)
 If no pin voltages replace SMPS.
3. If Backlights ON BUT PANEL SECTION(S) OFF:
 The Supply Drive (+) pins and (-) pins. All should measure same.
 If a Minus (-) pin measures low (near 0 volts), a string(s) of LEDs are likely open.
  Replace Panel.
 If a (+) pin measures low voltage.
  Defective SMPS.

BACKLIGHT DIMMING PROBLEMS :

• Go to Menu > Picture > Backlight and vary level (0 – 50).
• If no backlight changes observed:
 Panel Connector CNL801 minus (-) pin voltages and PWM_BLU control voltages CNM801 while changing backlight level.
• If minus (-) pin voltages don’t change, and PWM_BLU changes, replace SMPS.
• If PWM_BLU doesn’t change replace Main/T-Con Board.

Backlight Test : In normal TV operating mode, use standard IR Remote or Factory Remote with commands.
Go to (MUTE > 4 > 1 > 9 > EXIT)

Netflix Operation/Connection Issues.

Check Certificate & Netflix ESN Status in Factory Mode.

If Certificate and ESN exists, "CO", "NfO", change the DNS to 8.8.8.8
• If Certificate is missing, "C/" replace the TV’s Main Board.
• If ESN number is missing: NF/ do not replace the Main Board.
- Reset TV Clock and check for correct Time & Date. 

Netflix relies on correct settings.
- Reset Smart Hub. / Reset Apps In Factory Mode.

For Streaming Issues.

Go to TV Web Browser / Go to speedof.me / testmy.net
Check Speed for at least 5 Mbps(HD streaming) / 25 Mbps (4K Streaming).

Check Latency for less than 50ms.

Setting TV into Factory Mode

Factory Remote.

1. Power TV ON.
2. Select TV Source.
3. Info > Factory.
4. Use MENU for return.

Samsung IR Remote.

1. TV Power Standby.
2. Press as follows.
• Remote Buttons (NTSC-MUTE 1 8 2 POWER) 

PAL  INFO MENU MUTE POWER

Important Items.
• Option (must set Option Bytes when replacing Main Board.)
• Option > Factory Reset (returns TV to out of box condition.)
- Must perform when replacing Main Board or Full One Connect)

Factory Reset : Select Factory Reset.

SVC > Info > ER Count (Important to check for errors.)
- Resets to 0 with Factory Reset.
Check before resetting TV
• SVC > Test Patterns (Use to check / troubleshoot) videos errors.
• Control > EDID (Use to Reset HDMI Operational Errors)

Setting Option Bytes.

1 Enter Factory Mode with Service Remote (only).
2. Check Option Byte Table located on GSPN (Fast Track or Tips).
3. Select Option.
4. Select each item to change.
5. Can Use new Writing Type to enter model (if entered wrong it will not change.)

6. Soft power TV Off to load.

Performing Factory Reset.

Enter Factory Mode.
2. Select Option > Factory Reset
3. TV will power off.
4. Perform ALL TV Settings. (New out of box condition)

Details: UA65RU7100KXXV

Main board

How to enter service mode - Mitsubishi Laservue DLP projection TV - Service adjustments - Service mode - SMPS Schematic

LASERVUE PROJECTION HDTV V46 CHASSIS 

Light Engine : DLP® (1080p) 

Power Input : AC 120V, 60Hz - 

Tuning : 1 NTSC/ATSC/QAM

Service procedures

Many service functions and adjustments are accessed using the Remote Control.

Option menu
1. Press the <MENU> button on the remote control.
2. Press the buttons <2-4-7-0>. The screen will display the Option Menu. [Service Mode]

Service level initialization.
Service Level Initialization is used to restore all customer menu, video and audio settings to the original factory default condition.
1. Enter the Option Menu <MENU><2-4-7-0>
2. Select “Initialize” and <ENTER>

Deactivate VUDU.
This feature will deactivate the customer’s VUDU on-line subscription. It should be used before TV ownership is changed. NOTE: This feature is independent of the Initialize function.
1. Enter the Option Menu <MENU><2-4-7-0>.
2. Select “Deactivate VUDU” and <ENTER>.
3. The “VUDU Reset” text will momentarily turn red.
4. Press <EXIT> to quit.
5. The TV will register as deactivated the next time it is connected to the internet.

Digital signal strength.
1. Tune to a Digital Channel.
2. From the Option Menu, scroll down and highlight “Digital Signal Strength.”
3. Press <ENTER>. The screen will display the Digital Signal Strength Menu.

SNR Recommended Levels:
8VSB = 16 to 33
64 QAM = 22 to 35
256 QAM = 27 to 38

Reset / Initialization.

Many symptoms that are customer generated, intermittent or cannot be verified can be resolved by using the various Reset and Initialization options. Before visiting the customer’s home ask the customer to 1st perform a System Reset by pressing the <POWER> button on the side panel and holding it for 8 seconds.

 If this does not resolve the issue, they can perform an A/V Reset by pressing the side panel <INPUT> + <VOL UP > buttons at the same time and holding for 10 seconds. Then, if necessary, perform a user level Initialization by pressing <MENU><1-2-3> <ENTER> with the remote.

The customer should be made aware when settings and/or options will be reset.

LED indications and self diagnostics
The front panel Power LED provides an indication of the set’s operation and the possible cause of a malfunction.

Self diagnostics
A blinking red and yellow Status LED will indicate an Error Code that can help determine the cause of a circuit failure.
 The number of Red blinks indicates the value of the MSD (tens digit) of the Error Code.
 The number of Yellow blinks indicates the value of the LSD (ones digit) of the Error Code.
Example: If the Error Code is “37”, the LED will continuously blink Red three times, followed by blinking Yellow seven times.

To perform a System Reset, press and hold the Power button for 10 seconds. Or, unplug the set for 10 seconds then restore power.

After 3 occurrences, the TV will be locked out and will not respond to Power On commands. After repair, use the following procedure to unlock the TV.
1. Perform a System Reset by removing and re-applying AC.
2. Press and hold the side panel <INPUT> + <VOL Dn> buttons at the same time until the Status LED returns to normal (about 5 seconds).

Error code log.
The Error Code Log may be helpful to retrieve the code for an error that occurred in the past.
To access the Error Code Log: Press <MENU> <3-5-6-4>

Code Log Definitions
 PAGE - Current page number
 CURRENT TIME - total hours of operational use.
 USAGE TIME - usage hours when the error occurred.
 CODE - the specific Error Code that occurred.
 STATUS: HAPPENED - Indicates an error was recorded.

Press <CANCEL> to erase the Log.

[The Error Code Log is intended as a reference tool and is not meant to be used as a final determination of a defective part].

Service adjustments.

There are 2 Types of Service Adjustments, electrical and mechanical:
Electrical Adjustments.
  Horizontal and Vertical Centering Adjustment.
  Index Delay Adjustment.
  Geometry Alignment.
  Data Transfer Functions.

Mechanical Adjustment.
  Top Mirror Adjustment.

Electrical adjustments

Specific Adjust Procedures follow
 Service adjustments are performed using the remote control.
 The Service Menu is used for all service adjustments.
 Test Patterns are generated internally.

Activating the Service Menu
1. Press the <MENU> button on a remote control. (The “MENU” display will appear.)
2. Press the buttons <2-4-5-7>. (The Service Menu On Screen Display will appear.)
If no display appears, press <EXIT> and repeat steps 1 and 2.

Test Pattern Activation
1. When in the Service Menu, press Play  to activate the internal test patterns (no indication will be displayed initially). Use FWD and RWD to toggle between patterns.
2. Press Play a second time and use FWD and RWD to access additional patterns.
3. Press Play  again to toggle back to the previous patterns.

Adjustment Selection
When in the Service Menu use the <VIDEO> button to toggle to the adjustment desired as indicated by the number and abbreviation displayed on screen, i.e. “1.HVPOS.”

Adjusting Data
After selecting an adjustment item, use the Navigation UP/DN, LEFT/RIGHT buttons to perform the adjustment.

Saving Data
Press <ENTER> to save the adjustment data. The menu display will turn red for approximately one second. Note: If the circuit adjustment mode is terminated without pressing <ENTER>, changes in adjustment data are not saved.

Data Transfer & Geometry Menu
While in the Service Menu, press the <0> button to activate the Data Transfer & Geometry Menu.

Exiting the Service Menu
Press <EXIT> to quit.

Horizontal and Vertical Position Adjustment
1. Enter the Service Menu <MENU><2-4-5-7> .
2. Select the Geometry Test Pattern shown Play Rewind x2.
3. If necessary, select the adjustment, “1.HVPOS” <VIDEO>.
4. After selecting the HVPOS adjustment item, use the Navigation UP/DN, LEFT/RIGHT buttons to center the display.
  If a Up/Down button is pressed, the vertical position and VPOS adjustment data changes.
  If a Left/Right button is pressed, the horizontal position and HPOS adjustment data changes.
5. Press <ENTER> to save the adjustment data.

TSP Alignment (after Optical Engine replacement)
1. Enter the Service Menu <MENU-<2-4-5-7>.
2. Select the TSP Test Pattern by pressing PLAY once, then FAST FORWARD  or REWIND  until the pattern shown appears.
3. Use the <VIDEO> button to select “2.TSP”.
4. Use the DIRECTION buttons to straighten the horizontal lines, see example.
5. Press <ENTER> to save the adjustment.

Select Calibration Table (after Light Source Unit replacement)
1. In the Customer’s Video Settings Menu select COLOR TEMP: HIGH
2. Enter the Service Menu <MENU-<2-4-5-7>.
3. Use the <VIDEO> button to select the adjustment, “61.BCMH” and note the data value (0, 1, 2, 3 or 4).
4. Select the Green Double Ramp Pattern by pressing PLAY <w> twice, then FAST FORWARD or REWIND  until the pattern below appears.
5. Check the pattern for smoothness of graduation from dark to light and for the presence any vertical contour lines.
6. Use the DIRECTION  buttons to alternately change the Data Value of “61.BCMH” to 0, 1, 2, 3 or 4.
As necessary, press PLAY once to observe the Service Menu on screen display and press PLAY twice to return to the pattern.
7. Select the data value 0, 1, 2, 3 or 4 that gives the best results. No higher data value should be used.
8. Press <ENTER> to save the adjustment.

Manual Geometry Alignment
1. Activate the Service Mode <MENU><2-4-5-7>. From the Service Menu, press the <0> button. The Data Transfer & Geometry Menu will appear.
2. Use the Up/Dn buttons to select “MANUAL GEOMETRY ALIGNMENT” and press <ENTER>.
3. The Manual Geometry Alignment Pattern will appear. See below.
4. Prepare for the alignment by resetting the geometry data. Press <1> then <ENTER>. The previous menu will be displayed. Select “MANUAL GEOMETRY ALIGNMENT” and press <ENTER> again to proceed.
Note 1: Upon entering the Manual Geometry Alignment Mode the first time, the geometry may appear distorted because all factory geometry correction is automatically disabled. Press <EXIT> to quit and re-enable the factory geometry correction. Pressing <1> <ENTER> and <EXIT> will cause the TV to operate with out factory geometry correction (distortion will be present).

[At any time the original factory geometry data can be restored from backup:  

 From the Data Transfer & Geometry Menu <MENU><2-4-5-7><0>, select “RESTORE GEOMETRY DATA FROM BACKUP” <ENTER>.

Phase 1 - 20 Point Geometry Alignment
1. 20 Adjustment Points are indicated by white dots around the edge of the raster. The adjustment position is indicated by a + cursor.
2. Starting from the upper left corner, use the buttons to align the + at each point in a straight line, flush with the bezel as a reference.
Note: Only the cursor will move. The Geometry Pattern will not change.
3. After adjusting each point, use the <uu> button to shift the cursor to the next point clockwise and repeat until all 20 points have been adjusted.
4. After all 20 points are adjusted and the cursor is returned to the original starting point, press <ENTER>.
Correction will be automatically calculated and saved and the Manual Geometry Alignment will be terminated.
5. Press <ENTER> to re-activate the Manual Geometry Alignment. The geometry pattern will appear with the corrections applied.

Phase 3 - 4:3 and 16:9 Alignment
1. With the Manual Geometry Alignment activated, press <VIDEO> to enter the Left 4:3 Alignment Mode. The pattern below will be displayed.
Note: Pressing <VIDEO> will toggle between the Left 4:3, Right 4:3, Top 16:9, Bottom 16:9 and the 20 Point Geometry Alignment modes.
2. In the Left 4:3 Alignment Mode, pressing << or >> will cause the geometry pattern to be displayed with 12 preset amounts of correction. Toggle through them until you find the one with the straightest Blue 4:3 Line.
It may help to count the patterns as you cycle through them. When you find the pattern with the straightest Blue 4:3 Line, press <VIDEO>. The pattern will be displayed with a Right Blue 4:3 Line.

3. In the Right 4:3 Alignment Mode, pressing <<or >> will cause the geometry pattern to be displayed with 12 preset amounts of correction. Toggle through them until you find the one with the straightest Blue 4:3 Line. Again, count the patterns as you cycle through them. When you find the pattern with the straightest line, press <VIDEO>. The Top Red Line will be displayed in the pattern.

4. In the Top 16:9 Alignment Mode, pressing << or >> will cause the geometry pattern to be displayed
with 30 different preset amounts of correction to the Top Red Line. Toggle through them until you find the one with the straightest Red Line. Again, count the patterns as you cycle through them. When you find the pattern with the straightest line, press <VIDEO>. The Center Red Line will be displayed in the pattern.

5. In the Center 16:9 Alignment Mode, pressing <<or >> will cause the geometry pattern to be displayed with 30 different preset amounts of correction to the Center Red Line. Toggle through them until you find the one with the straightest Red Line. Again, count the patterns as you cycle through them. When you find the pattern with the straightest line, press <VIDEO>. The Bottom Red Line will be displayed in the pattern.

6. In the Bottom 16:9 Alignment Mode, pressing <tt> or <uu> will cause the geometry pattern to be displayed with 30 different preset amounts of correction to the Bottom Red Line. Toggle through them until you find the one with the straightest Red Line. When you find the pattern with the straightest line, press <VIDEO>. Press <ENTER> then <EXIT> to exit and save the 4:3 and 16:9 data.
7. Select the Geometry Test Pattern (See HVPOS). If Geometry is acceptable, press <EXIT> to quit.

Data Transfer
Service Data is duplicated and stored in separate EEPROMs in two locations.
  PWB-MAIN - Working data for TV operation
  OPTICAL ENGINE - Backup data

Enter the Service Mode <MENU><2-4-5-7> Select the Data Transfer & Geometry Menu <0>

[[Warning - Only use "SAVE ENGINE AND GEOMETRY SETTING TO BACKUP" after Optical Engine replacement]]

Note: Besides MANUAL GEOMETRY ALIGNMENT, six data transfer choices are listed on screen.
  RESTORE ENGINE DATA FROM BACKUP - copies backup factory adjustments HVPOS, White Balance and Index Delay from the Optical Engine to the PWB-MAIN.
  RESTORE GEOMETRY DATA FROM BACKUP - copies backup factory Geometry Alignment data from the Optical Engine to the PWB-MAIN.
  SAVE ENGINE AND GEOMETRY SETTING TO BACKUP - copies all working data from the PWB-MAIN into backup memory on the Optical Engine.
  BACKUP AND RESTORE ISF SETTINGS - allows the ISF (ADV) video settings to be backed up and restored using an external USB memory device.
  RED ONLY AND GREEN ONLY - displays the video in red or green only.

2. Use the UP/DN buttons to select the item and press <ENTER>.
3. Follow on-screen instructions if given.
4. Press <EXIT> to quit.
After Optical Engine Replacement:
1. Save Engine and Geometry Setting to Backup
After Electrical Chassis (PWB-MAIN) Replacement:
1. Restore Engine Data From Backup
2. Restore Geometry Data From Backup.
3. Restore ISF Settings From Backup (Only if backup USB memory device is available).

V46 SMPS [Power supply] Schematic