TOSHIBA 26HL84 SERVICE MODE - LED BLINKING CODES - SELF DIAGNOSIS

TO ENTER SERVICE MODE

1. Press "Mute" button on the remote control once.  "1/2" Mute will be displayed on the screen.
2. Press "Mute" button on the remote control again.  "Mute" will be displayed on the screen.
3. Press "Menu" button on the 'TV', while pressing the "Mute" button on the remote control. "S" will appear on the screen, indicating that the set is in Service Mode.
4. Press "Menu" button on the remote control.  Adjustment screen will appear on screen.

SERVICE MODE SCREENS: EXAMPLES

[1]

=================================

                              1/2 MUTE

==================================

 [2]

==================================

                             MUTE

==================================

[3]

==================================

                                                              

                                                            S

===================================

[4]

===================================

   RCUT

       60H

===================================

To "Exit" Service Mode, turn OFF the Power to TV or by remote control.

BUILT IN SIGNAL

• When press the "Input" source selection button on the remote control during Service Mode generate the built-in test video signal for servicing.

--------------------------------------------------------------------------------------------------

Built-in test video signal [used for adjustment such as White Balance etc.]

--------------------------------------------------------------------------------------------------

General broadcasting signal => Red Monochorme => Green Monochrome

=> Blue Monochrome => White Signal => Black Cross Bar => 

Built-in signal Off.

---------------------------------------------------------------------------------------------------

ADJUSTMENT ITEMS

1. Brightness Correction:  [1]  Receive a general broadcasting program.  Press the "Menu" button on the remote control, set the unicolor to minimum (00) and brightness to standard (00) in order to display the "Setting Menu" => "Picture Setting" => "Picture Adjustment" by pressing the Cursor [Up | Dn] & [Cursor Right | Left] buttons.  [2]  Select BRTC (Brightness Correction) using Cursor buttons "Ch up | Ch Dn" on the remote control, fine adjust the black signal to be black using "Vol Up | Vol Dn" buttons on the remote control.  After the adjustment, set 'Unicolor' back to initialize data.
2. White Balance:  [1]  Enter the Service Mode, press 'Input" source setting button on the remote control to generate the built-in white signal.  [2]  Adjust the Data of items [RCUT, GCUT & BCUT] for proper white balanced picture in low light area. [For high light area [GDRV & RDRV items should be adjusted for proper White Balanced picture

   SELF DIAGNOSIS FUNCTION

Press [9] button on the remote control during display of adjustment menu in service mode.
The display will be:
<SELF CHECK>
-----------------------------------------------------------------------
NO  12345678
POWER:  000
BUS LINE:  OK
BUS CONT:  OK
BLOCK:  MAIN SUB
SET ID:  01
EEP VER:  01
OPT 1:  05          OPT 2:  70.
SW VER: LCD MAY            9         2003       18:29:58
DVI:                                           BEP
NO 2300                                      SW VER: 0C
ERR CODE: 01   E2P VER:10
TIME:  05
------------------------------------------------------------------------
INITIALIZATION OF SELF DIAGNOSIS DATA

• Enter the service mode.
• Press and Hold the "Recall" button on the remote control and then press the "Channel Up" button on the TV.  Initialization have been done.

TOSHIBA 14JL7E 20JL7E 20JL7R SERVICE MODE - ADJUSTMENTS

APPLICABLE TO:  14JL7E _ 14JL7H _ 14JL7R _ 20JL7E _ 20JL7H & 20JL7R

TO ENTER SERVICE MODE

1. Press the "mute" button once on the remote control.
2. Press the "Mute" button again to delete the 'Mute' mark on the screen.
3. Hold Down "Mute" button, while pressing the 'Input' button on the "TV" while to enter the TV service mode.  
4. The service menu setting will be appeared as follows:

============================================

SERVICE MODE

1. RGB                                                    2. DEF

3. COMB                                                4. OTHERS

5. TA 1304                                              6. MSP 3410

7. IIC.                                                      8 . OPTION

9. AFT                                                    10. VOL

11. BRIGHT.                                         12. RESIZE

=============================================

• Switching setting screens > Ch Up | Ch Dn buttons
• Seleting setting screens > Volume Up | Volume Dn buttons.
• Resetting service mode > TV Power OFF.

TO SELECT AN ITEM TO SEE THE SETTABLE ITMES.

1. Switching items >> Channel Up | Channel Dn
2. Returning to top menu >> "Call" button on the remote control.

ADJUSTMENTS IN SERVICE MODE

• Use Volume Up | Dn button to change the settings.

SETTING AND ADJUSTING DATA

---------------------------------------------------------------------------------

Switching items using the CH Up | Ch Dn button

---------------------------------------------------------------------------------

1. BRIGHT -> 2. PICTURE -> 8 -> R-Cutoff -> 9. G-Cutoff -> 

10. B-Cutoff -> 12. G Drive -> 13. B-Drive. -> 1 Bright

---------------------------------------------------------------------------------

The direct select buttons [0 to 9] correspond to main the RGB-related settings.  

REMOTE CONTROL BUTTONS | TV SWITCHES IN SERVICE MODE

----------------------------------------------------------------------------------

Switching items using [Ch Up | Ch Dn] buttons.

----------------------------------------------------------------------------------

1. V_CENTER --> 46. H_ POS --> 1 V_CENTER

----------------------------------------------------------------------------------

COMB >>> Not used

OTHERS >>> Not used.

TA 1304

-----------------------------------------------------------------------------------

Switching items using Ch Up | Ch Dn buttons

-----------------------------------------------------------------------------------

1 WCTL -> 2 BASC -> 3 TREC -> 4 WON 1 -> 5 WON 2

-> 6 WOFF -> 7 EBAS -> 8 ETRE -> 9 EVOL -> 10 BASX -> 

11 TREX -> 12 TONN -> 13 ALS -> 14 W100 -> 15 W70 

-> 16 W40 -> 17 V100 -> 18 V75 -> 19 V50 -> 20 V25 -> 

21 V01 -> 22 VOLX -> 23 BASI -> 24 BAS2 -> 25 TRE 1 -> 

26 TRE2 -> 27 WLF1 -> 28 WFL1 -> 1 WCTL

------------------------------------------------------------------------------------

MSP 3410

------------------------------------------------------------------------------------

Switching items using Ch Up | Ch Dn buttons

------------------------------------------------------------------------------------

1 V01 -> 2 V25 -> 3 V50 -> 4 V75 -> 5 V100 _ 6 LODN

-> 7 BASX -> 8 BASC -> 9 TONN -> 10 TREX -> 11 TREC

12 WON1 -> 13 WCTL -> 14 MDBLP -> 15 MDBHP

16 MDBHM -> 17 BAS1 -> 18 TRE1 -> 19 WFL1 -> 20 BAS3

21 TRE3 -> 22 WFL3 -> 23 VOLX -> 24 VOLS -> 25 FVOL

26 FVDK -> 27 NVOL -> 28 NICL -> 29 NICH -> 30 IDL

-> 31 IDH -> 32 XVOL -> 1 VOL ---> <---

------------------------------------------------------------------------------------

IIC [Indicates Bus line communication status]

-----------------------------------------------------------------------------------

                                                                            S

IIC

TUNER: OK

AUDIO: OK

EEPROM: OK

AV SW: OK

RESIZE: OK

NT3  B/G --------

------------------------------------------------------------------------------------

OPTION

------------------------------------------------------------------------------------

Switching items using Ch Up | Ch Dn buttons

------------------------------------------------------------------------------------

1 MTS -> 2 HOTEL -> 3 TEXT -> 4 POSITION -> 5 A PRO

6 FM -> 7 ON_TIMER -> 8 VIDEO -> 9 LANGUAGE 

-> 10 MFLG1 -> 11 MFLG2 -> 12 MFLG3 -> 13 MFLG4

14 MEM_INI -> 1 MTS -> <---

------------------------------------------------------------------------------------

INITIALIZING MEMORY IC

• Enter the service mode.
• Hold down the 'Call' button on the remote control, and select [D] (Design mode), with Ch up | Ch Dn button.  
• Holding Down the "Call" button on the remote control and 'Ch Up' on the TV simultaneously powers the TV ON and OFF.  This [a] initializes [b] registers the data.

NB:  NEVER TRY TO PERFORM INITIALIZATION UNLESS CHANGED THE MEMORY IC

TOSHIBA 22V506 MEMORY IC REPLACEMENT ADJUSTMENTS

WHEN REPLACING EEPROM (MEMORY) IC
Initial total of memory IC, Power On total hours and 'Micon' version can be checked on the screen.  Total hours are displayed in 16 system notation.

1. Turn ON the Power and set to "All Mode".
2. Set the "Volume" to minimum.
3. Press Both 'Volume Down' on the TV set, and channel button  '8'  on the remote control for more than '2' seconds.
4. After confirmation of each Check-sum, turn "Off' the Power.

NOTE:  The each item value might be different to each set:  See the display window.

======================================

CHECKSUM:                     40D3  >>                                > Initial setting data Check su.

LCD PWR ON:                   0000   >>                                > Power On total hours  

SUB:                                    DA0E77Y221 >>                    > Sub-Micon Check version.

DTV:                                   VA07E84181 >>                     > Main Micom check version.

EEPROM:                          W50T01CM00 >>                  > EEPROM  check version.

PICTURE:                          dispSmartPic >>                     > parameter.

======================================

CONFIRMATION OF INITIAL DATA

If a service repair is undertaken where it has been required to change the memory IC, the following steps should be taken to ensure the correct data settings while making reference to  Initial settings.  Initial data is attached.

• Note:  If a service is undertaken where it has been required to change the memory IC, the following steps should be taken  to ensure correct data settings  while making reference to initial settings.
• Turn On the Power, and set to 'All Mode".
• Set the 'Volume' to minimum.
• Press Both 'Volume Dn' button on the TV, and Channel button [6] on the remote control for more than 2 seconds.  
• NB:  No need to set data other position than 7200 & 72FF]
• Addresses now selected should blink.  Using the  'Up/Dn' button on the remote control, step through the addresses to be changed is reached.
• Press Let/right button to select Data.  When data is selected, it should blink.
• Again step through the data using 'Up/Dn' button until required data value has been selected.
• Pressing "Right /Left" button will make you back to 'addresses' for further selection if necessary.
• Repeat steps 4 to 6 until all data has been checked.
• When satisfied correct data has been entered, turn the Power Off to finish the data input.  
• [After the Data Input, set to initializing of Shipping]

1. Turn On the Power.
2. Set 'Volume' to minimum.
3. Press Both "Volume Dn' button on the TV, and channel button [1]  on the remote control for more than 2 seconds.
4. After finishing initilization of shipping, the unit will turn OFF automatically.
5. The unit will now have the correct data value for the new memory IC.

-----------------------------------------------------------

INIT:                              0001   0099

SUB:                               DA0E77Y221

DTV:                              CA07E84181

EEPROM:                     W50T01CM00

-----------------------------------------------------------

TOSHIBA 22LV506 DVD FIRMWARE UPDATE

1. Turn ON the power, and set the DVD mode.
2. Confirm that 'No Disc' will be appeared on screen.
3. Press both "Volume Down' button on the TV set & Channel button '5' on the remote control for more than 2 seconds.
4. Press "Vol Dn" button on the unit to check if all keys on the unit "Do Not" function.  [To check if DVD write mode is set:  When inserting update disc at Non DVD Write mode, the 'read error' will happen].
5. Insert the update disc.
6. Automatic read will start and "Firmware upgrade Please Wait" will be displayed on the screen. At this time, the horizontal noise lines may appear.  But no problem.   [Do not turn OFF the unit on the way or operate the keys on the unit and remote control.  Update error will happen, and cannot be done with the Up-Date of Up-Date disc.]
7. After update, Logo Screen will appear.
8. Unplug the AC cord, the plug it back again. [[ After the write, set to initializing of Shipping ]]
9. Turn ON the Power, and set the DVD mode.
10. Press Both "Volume Down" button on the TV and channel button '4' on the remote control for more than '2' seconds.  The "INITIALIZE 5 --> COMPLETE" will appear on the screen.
11. Unplug the AC cord and Re-plug it again.  [[ Check for the firmware version ]]
12. Turn ON the power, and set DVD mode.  
13. Press Both "Channel button '1'" on the remote control, and 'Stop" button on the TV set for more than '2' seconds.  Firmware version will be displayed on the to left of the screen.  When the changed version displays, the re-write will be completed.
14. Turn "OFF" the Power.

FIRMWARE VERSION DISPLAY

----------------------------------------------------------------

           No Disc

          ADLJB8214A

----------------------------------------------------------------

ADLJB: Fixed

8214:  Release Date [Eg: 2008.02.14]  { A=October.  B=November. C=December}

A: Released times on the same date.

Up-Date Disc:
Ref No: JG176
Part No:  APJG176139.

TOSHIBA 22LV506 PARENTAL PASSWORD CANCELLATION

If the stored 4 digit password in the Rating Level Menu need to be cancelled:

1. Turn ON the set.
2. Set the DVD to 'Stop' mode.
3. Check that "No Disc" is displayed on screen.
4. Simultaneously Press & Hold the 'STOP' button & Hold the "7" key on the remote control unit.
5. Hold down both keys for more than '2' seconds.
6. The On Screen Display image 'PASSWORD CLEAR; will appear.
7. The four digit password is now cleared.

TOSHIBA 22LV506 ELECTRICAL ADJUSTMENTS (2 of 2)

2 of 2
ELECTRICAL ADJUSTMENTS
ON-SCREEN DISPLAY ADJUSTMENTS

1. Set the volume to minimum.
2. Press 'volume Dn' button on the TV set, and the channel button [9] on the remote control for more than 2 seconds to display the adjustment mode on screen 
3. Use [Ch Up/ Ch Dn] buttons (0 to 9) to select options.
4. Press the 'Menu setup' on the remote control to 'End' the adjustments.
5. To display the adjustment screen for TV,AV or GAME, COMPONENT, HDMI, PC and DVD mode, press the 'Input Zoom' button on the remote control.
6. Receive a digital broadcasting signal.
7. to display the adjustments on screen for DVD mode, select the digital channel.
8. Press 'Vol Up/Vol Dn' button on the TV and the channel [9] on the remote control for more the remote control for more than 2 seconds.

Want any more details?  Please comment.

TOSHIBA 22LV506 22 INCH LCD TV-DVD COMBINATION SERVICE MODE ADJUSTMENTS - (1 of 2)

[1of 2]
TO ENTER SERVICE MODE

• Press and Hold both buttons simultaneously, according to the chart given below to enter each mode, either on the remote control or at the front panel of the TV.

Set condition	Set key	Remocon key	Standard time	Operations
TV mode	Vol Dn min	0	2 sec	Releasing of V-Chip password.
TV mode	Vol Dn min.	1	2 sec	Initialization of factory TV data.  “If you see factory initialization, the memories are reset such as channel setting, and the power on total hours”
DVD mode.  No disc	Vol Dn min.	4	2 sec.	Initialization of factory data.
DVD mod.  No disc.	Vol Dn min.	5	2 sec	DVD write mode.
All mode	Vol min	6	2 sec	Power On total hours are displayed on screen.  Can be checked of the Initial Data of Memory IC.  [used when replacing the memory IC]
All mode	Vol min	8	2 sec	Check the SUM data and Micon Version  on the screen.  [When replacing the memory IC]
All mode	Vol min	9	2 sec	Display of adjustment menu on screen.  [Electrical adjustments] (On screen display adjustments)
DVD mode [no disc]	Stop.	1	2 sec	Check of firmware version.[Rewrite for DVD firmware].
DVD mode.  No disc Electrical adjustments follows:	Stop.	7	2sec	Releasing parental lock.

TOSHIBA 42HM66 SERVICE MODE ENTRY METHOD

TO ENTER FACTORY MENU

• Open the User Menu.
• Select "General Settings"
• Entry 'General Setting' and select 'Factory Reset'
• Enter [2 => 0 => 0 => 5] by remote control.  The Factory Menu will appear.

TOSHIBA LCDAD194TW SERVICE MODE ADJUSTMENTS

TO ENTER THE SERVICE MODE

• Press "Menu" button and the AC Power ON/Off will activate the service mode.  MCU will do auto-level automatically.  
• Press 'Menu'. The OSD screen will located at the left top of the panel.

TOSHIBA 28MW7DB 28MW7DG ELECTRICAL ADJUSTMENTS [2 of 2]

[2 of 2]

ELECTRICAL ADJUSTMENTS.

ITEM	ADJUSTMENT PROCEDURE
Focus adjustment	# Enter the Service Mode and select any register item.  # Press TV/Video button  on the remote control until the balck corss bar pattern appears on the screen.  # Asjust Focus control  in the line output transformer (Top One) for well defined scanning lines on the picture screen.
Sub-Brightness [BRTC] [Note:  Constrict picture height until the vertical retrace line appears adjusting the item HIT (Height)]	# Set contrast to minimum and brightness to center by adjusting user controls. # Set the TV in service mode to get white cross bar of inside pattern.  # Select BRTC , and adjust the Volume Up/Dn to reduce the value, so that white portion of inside pattern slightly light.  # Adjust Vol Up/Dn to increase the data value of BRTC, and set it just before the difference between the belt of the vertical retrace, and the border of black portion of inside pattern is visible.  After that, return vertical height  and contrast.
Horizontal position adjustment [HPOS]	# Set the TV in service mode and get black or white cross-bar signal with video button on the remote control.  # Select either HPOS (Horizontal Phase) or VPOS (Vertical Phase) with Channel Up/Dn buttons, and adjust the horizontal or vertical picture position  to the center of the screen with Volume Up/Dn buttons.
Vertical amplitude adjustment.  [HIT]	# Set the TV in service mode, and get black or white cross-hatch signal with video button on the remote control.  # Select HIT with Channel Up/Dn buttons and adjust the vertical amplitude by using Vol Up/Dn buttons, so that the first bar on cross hatch signal touches the edge of the screen.
White balance adjustment. Cut-Off adjustments Drive adjustments	# Set contrast to ‘40’ and brightness to ‘+20’ by picture control.  # Set TV in Service Mode and get the inside W/B adjusting signal with video button.  # Select R-Cut, G-Cut and B-cut with Channel Up/Dn buttons to set individual values to initial reference data with Volume Up/Dn buttons on the remote control.  # Press [-/---] button on the remote control and rotate screen VR to get a slight horizontal line on the screen.  For every pressing of [-/---] button provides Horizontal line picture and normal picture alternately.  # Press [-/----] button to release horizontal line picture, and select the tow other colors which did not light in the above step with Channel Up/Dn buttons.  Then tap Volume Up/Dn buttons so that three colors slightly light in the same level.  *To correct white balance in light area, select GDRV with Channel Up/Dn buttons to adjust.  ** To correct white balance in dark area, perform fine adjustment of R-Cut, G-Cut and B-Cut.

TOSHIBA 28MW7DB 28MW7DG SERVICE MODE AND ADJUSTMENTS - Self Diagnostic Function [1 of 2]

[1of 2]

ENTERING SERVICE MODE

• Press the 'Mute' button on the remote control. A  mute symbol will be appeared.
• Press 'Mute' button again and Hod it.
• While pressing the "Mute" button, press "Menu" button on the front panel of the TV.
• Will display the adjustment Menu.
• Press 'Mute' button on the TV. "S" will be displayed on the upper right corner of the screen.

KEY FUNCTION IN THE SERVICE MODE

1. A single horizontal line ON/OFF >> [-/---] button on the remote control or 'Power' button on the front panel of the TV.
2. Test signal selection >> 'Power' button on the remote control.
3. Selection of the adjustment item >> Channe Up/Dn button, either on the remote control or at the TV.
4. Change of the data value to selected item >> Vol (+/-) either on the remote control or at the front panel of the TV
5. Adjustment menu On | Off >> Menu button.
6. Initialization of memory >> Call + Channel [Up] button on the TV. (Never try to perform initialization unless you have been changed the memory IC) 
7. Reset the count of operating protect circuit to "00" >> Call + Channel [Dn] button on the TV.
8. R-CUT selection >> 1 button.
9. G-CUT selection >> 2 button.
10. B-CUT selection >> 3 button.
11. CNTX selection >> 4 button.
12. COLC selection  >> 5 button  ----- Color thickness correction.
13. TNTC selection  >> 6 button ----  [Note: May display differently depending on the setting of the receiving color system.  COLP = PAL |  COLC = NTSC | COLS = SECAM]
14. Test Audio Signal On/Off  >> 8 button.
15. Self diagnostic display On/Off >> 9 button.

SELECTING THE ADJUSTING ITEMS

• Every pressing  of the 'Channel Up' button in the service mode, changes the adjustment items.

ADJUSTING DATA

• Press of 'Volume ( +/- )' button will change the value of the data in the range from [00H to FFH].  The variable range depends on the adjusting item.

TO EXIT SERVICE MODE

• Press the "Power" button to turn OFF the TV once.

INITIALIZATION OF MEMORY DATA OF QA-02.

1. Enter the 'Service Mode' and select any register item.
2. Press and Hold the 'Call' button on the remote control, and press 'Channel Up' button on the TV.  The initialization of QA-02 is completed.
3. Check the picture carefully.  If necessary, adjust any adjustment item.  
4. Perform "Auto Search Memory" function to make sure it works correct.  

TEST SIGNAL SELECTION

• Every pressing of 'Power' button on the remote control changes the built-in test patterns on the screen in 'Service Mode'.  [Toggle between NTSC signals (14 patterns) => PAL signal (14) patterns => signal Of =>]

SELF DIAGNOSTIC FUNCTION

1. Press (9) button on the remote control during display of Adjustment Menu in the Service Mode.  The diagnosis will begin to check if interface among ICs are executed properly.

Diagnosis Screen

==================================

                    <SELF CHECK>

 2390****

POWER      : 00

BUS LINE  : OK

BUS CONT: OK

BLOCK      : UV  V1  V2  QV1

==================================

• 2390**** is part number of microcomputer.
• Operating number of the protecting circuit  --- '00' is normal.  When indication other than '00' over current apts to flow, and circuit part may possibly be damaged.
• BUS LINE CHECK: 'OK' is normal.  [SDA 1-GND = SDA-GD short circuit.] [ SCL 1-GND = SCL-GND short circuit] [ SCL 1-SDA 1 = SCL-SDA short citcuit.]
• BUST CONT ---'OK' is normal. (When indication shows "QoooNG", the device with the number may possibly be damaged.)
• BLOCK: (UV=TV reception mode.  V1=Video 1 input mode.  V2=Video 2 input mode]

Others

Indicated color of mode now selected: Green and Red.

Indicated color of other items: White.

Green: Normal.

Red: The microcomputer operates to provide judgement of no video signal.  The red color is still indicated though the signal is input, failure may exists in input signal line including QV 1

QV 1 :  In the case of indication Green = Normal

             In the case of indication red  with input signal = Failure may exist in output line including  QV 1.

• In the case that the 'Power' indicator is blinking with intervals of (0.5) seconds, means the protecting circuit is operating, and circuit component may possibly be damaged.  Check related components.
• In the case that the 'Power' indicator is blinking with interval of (1) second, protection circuit does not operate, but a part of Bus Line does not operate normally.  Check bus Line.

will continue:

SONY TRINITRON KV20S90 SERVICE MODE & LED BLINKING CODES.

             TO ENTER SERVICE MODE [REMOTE CONTROL RM-Y155]

• Make the set to 'Standby' mode.  [Switch it on by its AC mains Power Switch, and press the 'Power' button on the remote control to make it 'Standby'.
• In Standby mode, press [Display => Channel (5) => Volume (+) => Power] buttons by remote control.  Press each button within a second of each other.
• Service Mode will be displayed as follows:

=====================================

SERVICE                   HSIZ                          0

=====================================

Descriptions:

• SERVICE > Mode.
• HSIZ > Display item.
• 0 > Data

Press [1] of [4] button on the remote Conrail to call an item to adjust.

Press  [3] of [6] button on the remote control to adjust the data value to selected item.
Press [Muting] and then press [Enter] button to write the adjusted data value into memory.
Turn 'OFF the set to 'Exit' service mode.
Press [8] then 'Enter' on the remote control to initialize.  After replacing the memory IC [IC003] carry out initialization.
 MEMORY WRITE CONFIRMATION METHOD

• After all adjustments, pull out the plug from AC outlet, then re-insert the plug in the AC outlet again.
• Turn the 'Power Switch' ON and set to Service Mode.
• Call the adjusted items again, to confirm they were adjusted.

LED BLINKING CODES

When an error occurs, the Standby/Timer LED will flash a set number of times to indicate if possible cause of the problem.  If there is more than one error, the LED will identify the first of the problem areas. 

Result for all of the following diagnostic items are displayed on the screen.  No error has occurred if the screen displays a "0".

SELF-DIAGNOSTIC FUNCTION [LED BLINKING CODES]

Diagnostic item description	No. of times standby/timer LED lamp flashes.	Self diagnostic display/Diagnostic result	Probable cause location.	Detected symptoms.
Power does not turn ON	Does not flash	----------------	# Power cord is not plugged in.  # Fuse is burned out [F601] (A-Board)	# Power does not come ON.  # No power is supplied to TV.  # AC power supply is faulty.
+B overcurrent (OCP)	2 times	2:0 or 2:1	# H.Out [Q502] is shorted.(A-Board)  # IC1751 is shorted (C-Board)	# Power does not come ON.  # Load on power line is shorted.
Vertical deflection stopped	4 times	4:0 of 4:1	# +13V is not supplied (A-Board). # IC541 is faulty (A-Board)	# Has entered standby state after horizontal raster.  # Vertical deflection pulse stopped.  # Power line is shorted or power supply is stopped.
White balance failure	5 times	5:0 or 5:1	# Video Out [Q392 to 394] is faulty (A-Board).  # IC 301 is faulty (A-Board).  # Screen [G2] is improperly adjusted.	# No raster is generated.  # CRT cathode current detection  reference pulse output is small.

SONY TVC PLASMA PFM-500 PFM510 SERIES SERVICE MODE ADJUSTMENTS [3 OF 3]

[3 OF 3]
DIGITAL TYPE > Selects either RGB signal or YUV signal  as the input signal to the 'digital in' terminal.  

• RGB: The RGB signal is selected as input signal to the 'Digital In' terminal.
• YOV:  The YUV signal is selected as the input to the 'digital input' terminal.
• Set the digital type item to the 'RGB' position normally.

RGB 2 TYPE > Selects ether RGB signal or the YUV signal as the input signal to 'RGB 2' terminal.

• RGB:  The RGB signal is selected as the input signal to RGB2 terminal.
• YUV :  The YUV signal is selected as the input signal to RGB2 terminal.
• Set the RGB2 item to the RGB position normally.

AUTO PLL SETUP > Sets enable/disable of automatic execution of the 'Pixel Adjust' function.  ON:  When 'ON' the 'Pixel Adjust' is automatically executed when the main power is turned on or when input signal is switched.  Be noted that above 10 seconds are required to output the video signal after switching the input signal when this function is kept "ON" position.

• OFF:  The automatic pixel adjust is executed only when 'Auto' item of the user manu 'Pixel Adjust' is activated.  This function becomes valied only when the signal that enables the 'Pixel Adjust' is inputted into the PFM500A3W/510A2W. [Set the 'Auto Pll Setup' to the 'OFF' position normally.

AUTO PLL PIXEL > Selects the functions that are automatically adjusted when 'Pixel adjust' is executed.  

• ON:  Both the 'Total H Pixel' and 'Dot Phase' are automatically adjusted.
• OFF:  Only 'Dot Phase' is automatically adjusted.  
• In the case PFM500A3W/510A2W used under the environment where the input signal contains much noise, there are cases that the 'Pixel Adjust' mis-operations.  Therefore, set the 'Auto Pixel' to the 'OFF' position.  In such case, the 'Total H Pixel' can be adjusted only manually.  This function becomes valid only when the signal that leanness the 'Pixel Adjust' is inputted to the PFM-500A3W/510A2W.  [Set the 'Auto Pixel' item to 'ON' position normally]

H/V SHIFT > Selects the method to control the horizontal and vertical picture shift.

• EDGE:  When 'Edge' is selected, a picture is shifted by changing the starting position when reading data into memory.  Using this function the entire area including blanking of all pictures can be displayed by shifting.  The variable range of shifting is '1' horizontal and vertical period respectively.
• CAPT:  When 'Capt' is selected, the picture that have already written into memory is shifted by a scan converter.  Using this function a picture can be shifted as much as (+/- 50%) of a picture.  When the picture is partially lacked at an end of a picture, the lacked portion of the picture cannot be displayed.
• Set the 'H/V Shift' item to 'EDGE' position normally.

VIDEO SHARP SW >  Sets analogue aperture On/OFF.  The methods are used for the aperture correction of the video signals  [NTSC/PAL/SECAM/NTSC4.43/PAL-60 & YUV signals having horizontal frequency of 15kHz].  These two methods are the scaling filter and the analogue aperture of the scan converter.

• ON:  Both the scaling filter and analogue aperture of the screen converter is used for aperture correction.
• OFF:  Only scaling of the screen converter is used for aperture correction.  [This function becomes valid only when the signal [NTSC/PAL/SECAM/NTSC4.43/PAL60 & YUV  signals having horizontal frequency of 15KHz] is inputted to the PFM-500A3W/510A2W
• Set the 'Video Sharp SW' item to 'ON' position normally.

AUTO FT CHANNEL > Sets the Field Tearing [FT] cancel circuit ON/OFF.  The PFM-500A3W/510A2W has the FT prevention circuit caused by over-run of memory while it is displaying the moving picture.  However there can be cases that noise appears on the screen when FT prevention is being executed. 

• ON:  Th FT is cancelled in every picture size and every shift conditions as long as the TV is receiving the moving picture.  When this item is set to "ON", noise may appear only once after the size/shift is adjusted.  Noise does not last long but appears only once when the size/shift adjustment is complete.
• OFF:  The FT cancel circuit is disabled.  When 'OFF' is selected there can be a case that  the field tearing appears on the screen depending on the adjustment conditions of the picture  size/shift.  However, noise due the operation of the processing circuit does not occur.
• Set the 'Auto FT Cancel' item to 'ON' position normally.

SONY TVC PLASMA PFM500 PFM510 SERIES ADJUSTMENTS [2 OF 3]

[2 OF 3]

• COLOR TEMP:  Only 'COLOR TEMP' area of EEPROM  is initialized.  When the 'color temp' area is initialized the color temperature data in High, Low and the user setup data from 1 to 6 are initialized to 255.  The users names are also initialized to 1 to 6.
• PROG.PRESET:  Only the PROG.PRESET are of the EEPROM  is initialized.  The preset area, for 20 types, that is reserved as space is initialized.
• FIXED PRESET:  Only Fixed Preset area of the EEPROM is initialized.  The basic preset area is initialized to the built in standard value that is stored in the system controller.
• LAST MEMORY:  Only the Last Memory area of the EEPROM is initialized, only the last memory data of every signal that is adjusted bu user is initialized. 
• USER MEMORY:  Only User Memory area of the EEPROM is initialized.  All of the 20 types of adjustment data that is saved by the memory function of the user menu are initialized to empty.
• FACTORY:  Only factory area of the EEPROM is initialized.  When Factory area is initialized, all areas of the memory, except the areas that are listed below are initialized.  
• Items that are not initialized by 'Factory Reset' function.

1. EEPROM ID CODE
2. INDEX NUMBER
3. MODEL NAME.
4. SERIAL NUMBER.
5. AUDIO DIGITAL
6. DIGITAL TYPE.
7. YUV2 TYPE.
8. AUTO PLL SETUP.
9. AUTO PLL PIXEL.
10. H/V SHIFT.
11. VIDEO SHARP SW.
12. AUTO FT CANCEL.
13. WATCH ERROR.
14. Y GAIN.
15. R-Y GAIN.
16. B-Y GAIN.
17. R CUTOFF.
18. B CUTOFF.
19. ADC R GAIN.
20. ADC G GAIN.
21. ADC B GAIN.
22. ADC R OFFSET.
23. ADC G OFFSET.
24. ADC B OFFSET.

MAIN MENU STRUCTURE

==========================

WHITE BALANCE

WINDOW = OFF

COLOR TEMP = HIGH

RED GAIN = 255

GREEN GAIN = 255

BLUE GAIN = 255

==========================

• WINDOW:  The PFM-500A3W/510A2W has the built in window signal  for white balance adjustment.  There are two sizes that are the large and small windows.  Select the optimum size window for white balance adjustment.  OFF > Window does not appear.  TYPE-1 > Small window.  TYPE-2 > Large window.  [When the white balance is going to be adjusted using an external signal perform the A/D converter calibration before starting the white balance adjustment.
• COLOR TEMP:  To adjust the white balance, firstly select the desired color temperature from High, Low, 1,2,3,4,5 or 6 on the color temp sub-menu.  Color temperature of items 1 to 6 are the same as those of the user menu.
• RED GAIN:  Adjust the Red Gain of the selected color temperature.  Range is from '010 to 255'
• GREEN GAIN:  Adjust the Green Gain of the selected color temperature.  The range of adjustment is from '010 to 255'
• BLUE GAIN:  Adjust the Red Blue of the selected color temperature.  The range of adjustment is from '010 to 255'.

ADC CALIBRATION MENU STRUCTURE.

Calibrate A/D converter IC 200 until non-uniformity between the R, G and B channels of the A/D converter is removed.

================================

ADC CALIBRATION

AUTO = OFF

CAL MODE = 128

RED GAIN = 128

GREEN GAIN = 128

BLUE GAIN = 128

RED BIAS = 128

GREEN BIAS = 128

BLUE BIAS = 128

R: ------- G: ------- B: ---------

================================

• AUTO:  A/D converter is automatically calibrated.  When sufficient adjustment accuracy cannot be obtained by the automatic calibration, perform basically the manual calibration using the following ADC CALIBRATION  menu items.
• CAL MODE:  A/D converter has the calibration mode as is operating mode as follows:
• A/D converter has R,G,B gain adjustments, and R,G,B bias adjustments.  The Gain adjustment of the converter are used for 'Contrast' adjustment to the machine.  The R,G,B Bias adjustments of the converter are used for the 'Brightness' adjustment of the machine.  [CAL MODE OFF] > Standard display state.  The R,G,B  bias values are controlled by Contrast/Brightness data of the user menu.  The R,G,B gain values and R,G,B bias values of the menu cannot be adjusted dependably     
• CAL MODE OFF: Calibration mode > The R,G,B gain values and the R,G,B bias values of this menu can be adjusted independently.  The R,G,B data that appears in the most bottom par of the menu in cyan, change from the indication "=====" to indication of any digital output data of the A/D converter. 
• RED-GAIN | GREEN GAIN | BLUE GAIN > The respective R,G,B gain values can be adjusted independently.  The range of the adjustment is form '000 to 255'.
• RED BIAS | GREEN BIAS | BLUE BIAS > The respective R,G,B bias can be adjusted independently.  The range of adjustment is from '000 to 255'.

VIDEO PROCESSOR

The following items for the video processor can be adjusted using this menu.  However, all the items of the video processor have the default values on which normal operations are performed.  There fore the video processor normally needs no adjustments.

===================================

VIDEO PROCESSOR

Y GAIN > 111

R-Y GAIN > 082

B-Y GAIN > 128

RED CUTOFF > 143

BLUE CUTOFF > 100

====================================

SPECIAL FUNCTION

Various special functions are listed in a 'Special Function' menu can be independlely set as required.

-----------------------------------------------------------------

SPECIAL FUNCTION

AUTO DIGITAL

DIGITAL TYPE

RGB2 TYPE

AUTO PLL SETUP

AUTO PLL PIXEL

H/V SHIFT

VIDEO SHARP SWITCH

AUTO FT CANCEL

----------------------------------------------------------------

AUDIO DIGITAL > Sets enable/disable of automatic switching of the 'digital In' terminal.

The PFM-500A3W/510A2W is equipped with the 'Digital In' terminal using the LDVS.  The automatic switching of the 'Digital In' can be enabled/disabled as follows by the setup of the 'Auto Digital' item of this menu.

• ON > When the 'Auto Digital' is set to ON, connect pin A20 to Gnd to switch the 'Digital In' terminal to the digital input.  Disconnect pin A20 open to switch the 'Digital In' terminal to the input state before the terminal is switched to 'digital'.
• OFF > When  the 'Auto Digital' is set to ON, the automatic switching of the 'Digital In' terminal is disabled.  Set the 'Auto Digital' item to the 'ON' position normally.

Will continue:

SONY TVC PLASMA - PFM-500 PFM510 SERIES - FLAT PANEL MONITOR - SERVICE AND ADJUSTMENTS [1 OF 3]

[1 OF 3]
SONY  PFM-500A3WE _ PFM-500A3WG _ PFM-500A3WU _ PFM-510A2WE _ PFM-510A2WG _ PFM-510A2WU [TVC-PLASMA]
BKM-500 > Input Adapter.
MB-514 > Mounting bracket.
RM-921 > Remote commander.
ELECTRICAL ADJUSTMENTS USING THE SERVICE MODE
The electrical adjustments can be performed using the remote commander [RM-921] supplied with  PFM-500A3W | 510A2W.  The remote commander has the service mode.  Select the Service Mode to perform the electrical adjustments.
SERVICE MENU
When enter the Service Mode, the mode menu appears as shown below.  The mode menu contains the three Menus of Main Menu, Service Menu and manual Menu.  Select the 'Service Menu' to perform the electrical adjustments.
---------------------------------------
        MODE SELECT
 MAIN MENU 
SERVICE MENU
MANUAL MENU
---------------------------------------
MAIN MENU >>  This is the user menu.  Use the Main menu when user adjustment items such as operation checks upon completion of adjustments, are going to be made.
SERVICE MENU >> This is Menu that is used for electrical adjustments.  
MANUAL MENU >> This Menu is used in production Factory.  Do not make any attepts  to use this Menu, and do not make any operations using this menu.  
Service Menu Option have:

1. EEPROM RESET  >> Initialization of EEPROM.
2. WHITE BALANCE >> Gain adjustment of digital gamma circuit.
3. ADC CALIBRATION >> Calibration of Analogue to Digital [A/D] converter.
4. VIDEO PROCESSOR >> Level adjustment of video processor circuit.
5. SPECIAL FUNCTION >> Setting the special functions.
6. PRESET EDIT >> Editing the preset signals.
7. MAINTENANCE >> Setting the data that are unique to the particular machine.
8. STATUS/TEST >> Internal status and function test.

TO ENTER SERVICE MODE

• Set the TV to "Standby" mode. [Turn the power On by its Main Power switch, and press the 'Power' button on the remote control once to make it Standby Mode]
• Press [Display => 5 => Volume(+) => Power] buttons on the remote control.

To Exit Service Mode

1. Turn OFF the Main Power and back ON to enter the Standby state (or)
2. Turn OFF the Main Power to EXIT the service mode.

SERVICE MENU STRUCTURE

• The entire area or the respective areas  of the EEPROM can be separately initialized.

Select the desired area of EEPROM to be initialized using the following menu.

-------------------------------------------------

EEPROM RESET

WHOLE AREA

COMMON

COLOR TEMP

PROG.RESET

FIXED PRESET

LAST MEMORY

USER MEMORY

FACTORY

-------------------------------------------------

To initialize the desired area, select the desired item from the EEPROM RESET menu.  Change the selected item from CANCEL to EXECUTE.  Then press 'Enter'.

• WHOLE AREA >>> The entire area of EEPROM is initialized.  Initializing the entire area of EEPROM ha the same result as all menu items of COMMON, COLOR TEMP, PROG.PRESET, FIXED PRESET, LAST MEMORY and FACTORY are executed. 
• COMMON >>> Only common area of the EEPROM is initialized.  When the common area is reinitialized the data that is unique to the particular machine and common data [CONFIG MENU, REMOTE MENU] are initialized.

Will continue:

SONY - KVPG21P40 KVPG21P70 KVPG21M70 KVPG21P40/L- Pearl Blue KV-PG21P40/N -Champange Gold LED BLINKING CODES AND SERVICE MODE

Service adjustments to these models can be performed by using the supplied remote commander RM-952.
TO ENTER SERVICE MODE

• With unit on standby press [Display => 5 => Volume (+) => Power] buttons on the remote control in sequence.  
• To exit service mode, Set in 'Standby' condition, press "Power" button on the remote control, and press "Power" button again.
• The set will display:

--------------------------------------------------------------------------------------

00              HPS                         33            SERVICE                 50

079S         1.6C                         00                  000A  

080S                                                                     PAL,SECAM:50

                                                                                        NTSC:60

-------------------------------------------------------------------------------------

Display Descriptions;

00 > Item Number.

HPS > Adjustment item.

33 > Data.

SERVICE > Mode

50 = depends on signal

079s{ 

080s} Suffix No (OEM) code

1.6C > Software verson.

000A > Total power On time (Hours)

METHOD OF WRITE INTO MEMORY

1. Set to service mode.
2. Press '1' (Up) and '4' (Dn), to select the adjustment.
3. Press 'Muting" button to indicate'WRITE' on the screen.
4. Press '0' button to write into memory.

MEMORY WRITE CONFIRMATION METHOD

• After adjustment, pull out the plug from AC outlet and re-plug it again.
• Turn the Power Switch ON, and set to Service Mode.
• Call the adjusted item/s again to confirm adjustments were made.

Use [1] & [4] buttons to select an adjustment item.

Use [4] & [6] buttons to raise/lower the data value to selected item.

Use [Muting] button to write.

Use [0] button to execute writing.

Other Function via Remote Control

[7]&[0] > All data becomes values in memory.

[8]&[0] > All user control goes to the standard state.

[5]&[0] > Service Data Initialization (Be sure not to use usually)

[2]&[0] > Copy and write all data.

[Mute] & [0] > Write 50Hz adjustment data to 60Hz and vice versa.

---------------------------------------------------------------------------------------------

Adjustment Method: An example. [Horizontal shift]

1. Select '00 HPS" with the '1' and '4' buttons.
2. Raise or lower the data with [3] and [6] buttons.
3. Select the optimum state. (the standard is (1F) for PAL reception.
4. Write with the "Muting" button. (The display changes to 'WRITE')
5. Execute the writing with the [0] button. (The 'WRITE' display will be changed to 'Red' color while executing, and back to 'SERVICE'.

{Use the same method for all items.}

When an error occurs, the standby/timer lamp will flash a set number of times to indicate the possible cause of the problem.  If there is more than one error, the lamp will identify the first of the problem areas.

LED BLINKING CODES

Diagnostic item description	No. of times Standby | Timer lamp flashes.	Self diagnostic display | Diagnostic result	Probable cause location	Detected symptoms
Power does not turn ON	Does not ligh	===========	# Power cord is not plugged in.  # Fuse is burned [F4601] (F)	# Power does not come ON.  # No power is supplied to TV.  # AC power supply faulty.
# +B over current.  # Horizontal deflection over drive.	2 times	002:000 or 002:001 to 255	H.Out Q801 is shorted [A-Board]	# Power does not come on.  # Load on power line is shorted.  # Has entered standby state after horizontal raster.  # Power line is shorted or power supply is stopped.
# White balance failure.  #  No picture.  # Vertical deflection stopped.	4 times	004:000 of 004:001 to 225.	# -13V is not supplied [A-board].  # IC 551 faulty. [A-Board].	Vertical deflection pulses is stopped.
Micro reset.	===========	101:00 or 101:001 to 225	# Discharge CRT [CV-Board].  # Static discharge.  # External noise.	# Power is shut down shortly, after this return back to normal.  # Detect micro latch up.