SOFTWARE: Zappa Projection Firmware.
HARDWARE: Zappa Projection TV, USB Flash Disk.
USB UPGRADE FUNCTION OVERVIEW
Zappa builds in USB OTG chip for F/W upgrade purpose; user just put F/W hex code into USB Flash Disk, and then plug it to USB receptacle of TV, system will upgrade the F/W to appropriate unit. There are 7 units can be upgrade, MTV512, VGA EDID, HDMI 1 EDID, HDMI 2 EDID, Pixel works Flash, DTV module Flash and CSC1220.
USB FLASH DISC USAGE
Zappa USB OTG only recongnizes USB flash disk device, other devices will be ignored
- File system: USB driver support FAT 12, FAT 16 and FAT 32 file systems. Also support OTG HOST mode only.
- File location: User can put F/W hex code in any directory or root directory.
- Sub File Name: Current driver only can recognize *.hex sub file name. So you may need to rename the sub file name to be “HEX”, such as DTV module, that F/W file name is “vxWorks_user.bin”, you need to rename it to be “vxWorks_user.hex”.
- File Name: Driver recognizes prefix file name then decide which unit should be upgraded, you can put any characters after prefix, such as date or version. For example, Mtv512_v02. hex, “Mtv512” is prefix and driver will recognize it and upgrade it to MTV512. The prefix file name of each unit list as below.
|
Upgrade
unit
|
Prefix
file name
|
Upgrade
sequence
|
|
MTV512
|
MTV512
|
1
|
|
CSC1220
|
CSC1220
|
2
|
|
VGA EDID
|
VGAEDID5020/
VGAEDID5820/
VGAEDID5880/
VGAEDID6580/
|
3
|
|
HDMI EDID
|
HDMIEDID5020/
HDMIEDID5820/
HDMIEDID5880/
HDMIEDID6580
|
4
|
|
Pixel Works
|
APPCODE720P/
APPCODE1080P
FLASHER.HEX
|
5
|
|
DTV Boot Code
|
BOOTROM
|
6
|
|
DTV Module
|
VXWORKS_USER
|
7
|
Can put all of above
files into disk or individual file that depend on what unit you want to upgrade.
And driver will follow the upgrade sequence to upgrade each unit.
About VGA EDID and
HDMI EDID, can put all of model’s EDID code in one USB Flash Drive, USB will
according to product ID in EDID EEP ROM to choice correct EDID code.
Note: if the
EDID EEP ROM is emtpy or the product ID is wrong, USB will pick one of EDID
code on the flash drive to upgrade. So, if you already know the EDID is empty, just
put one EDID code that you want to upgrade in USB Flash Drive.
UPGRADE LED INDICATION
Due to LED are
controlled by MTV512, so when MTV512 is upgrading, the LED will be lost control,
but when MTV512 upgrade complete, it will be reset and back to Standby mode,
all LED are OFF, except this unit, the LED indications as below description.
Status LED Behavior
Upgrade Proceeding LED rotates from left to right
Unit Upgrade Complete
POWER LED still on
Entire Upgrade
Process Complete POWER LED
flash
Upgrade Error TEMP and LAMP are
flashed both
USB UPGRADE PROCEDURE
- Put F/W hex code to USB Flash Disk.
- TV power state at Standby mode.
- Plug USB Flash Disk to USB receptacle of TV.
- LED rotates. (Except MTV512 Unit)
- Waiting for POWER LED flash or all LED off (MTV512)
- Power on TV.
- TV shows Upgrade Complete List report.
Note 1: Pixel
works upgrade function will decide what version will be upgraded (720p or
1080p). It depends on VGA EDID product ID, so before upgrade pixel works hex
code, please make sure your EDID code is right.
Note 2: If you
attempted to upgrade MTV512 and CSC1220, the LED behavior may become strange.
Note 3: If you
want to upgrade VGA EDID or HDMI EDID, please remove VGA cable or HDMI cable,
because the EDID 12C is wired with USB chip and VGA/HDMI 12C bus.
ERROR HANDLING
What situation Error
message occurs.
- Upgrade Pixel Works without flasher.hex.
- Unplug USB Disk during upgrading.
- HEX file format not correct.
- Upgraded unit no response.
