SANYO - LCD 26XR9DA _ SANYO - LCD 47XR8DA _ SERVICE MODE _ AND ADJUSTMENTS IN DETAIL

TO ENTER SERVICE MODE

• Press “SOURCE”, “2”, “5”, ”8” and “0” in turn to enter factory menu.
• Press “CH+” and “CH-” to move the cursor to the adjustment page of the level one factory menu, then press ”OK” to enter.
• Press “CH+” and “CH-” to move the cursor up and down.
• Press “VOL-” and “VOL+” to adjust the item when the cursor move to a certain adjust item.
• Press “MENU” to exit to the previous factory menu.
• Press “EXIT” to exit the factory menu at any situation.
• Press “OK” to enter the sub factory menu.

• ADC ADJUST, ADC calibration of VGA, Component channel.
• W/B ADJUST, white balance adjustment.
• POWER Mode, set the turn-on modes. Standby---standby when power on; Mem---memory; ForceOn---power on; ForceOn can be used for aging; set the “power mode” to “Standby” when preset ex-factory unless the client appointed it.
• ISP Mode, ON---soft upgrading through VGA port with ISP device, OFF---DDC function of VGA; the setting will not be memory and will be “OFF” when power on again.
• REST ALL, initialization of the factory and user data; after this item is confirm, the unit will restart and display the guiding image.
• Factory Data Reset, factory data initialization (including white balance adjustment, ADC calibration and other adjusted data).
• Factory Channel Preset, preset the factory channel; please connect to the center signal source when operating; the present digital frequency is CH28 (529.5MHz), CH33 (564.5MHz) for Australia and CH45 (666MHz) for UK, if the signal changes, perform “DTV manual search” in “Channel” menu and the operation needs 15s or so.
• MST Debug, the default is OFF. OFF---RS-232 should match the design criterion; ON--- it should be convenient for using exploitation tool to adjust. The setting will not be memory and will be “OFF” when power on again.
• Backlight: adjust the backlight brightness, adjust the data and test the voltage of X804 pin2
• (PWM), let the voltage to be the corresponding PWM voltage which the brightness is maximum.  It will be preset and doesn’t need adjust.
• SSC Adjust, adjust the frequency spectrum expand, it will be preset and doesn’t need adjust.
• AUDIO Curve, adjust the sound curve, it will be preset and doesn’t need adjust.
• Picture Mode, set the picture values of each channel. Normally, they are preset and needn’t adjust.

• There is data in EEPROM after software upgrade, please perform Reset All before the first adjustment.
• ADC calibration.
• ADC calibration in VGA channel.
• Switch to VGA channel.
• Press” SOURCE”, then press “2, 5, 8, 0” in turn to enter the level one factory menu.
• Move the cursor to “ADC ADJUST” and press OK to enter the sub-menu.
• Input VGA signal (VG-848 Timing:856(1024x768/60Hz), Pattern:920 Gray 8 step(H)). Move the cursor to “mode”, press CH+ and CH- to select “RGB”, move the cursor to “AUTO ADC” and press OK to adjust automatically till complete.

ADC calibration in YPbPr channel.

1. Switch to YPbPr channel.
2. Press” SOURCE”, then press “2, 5, 8, 0” in turn to enter the level one factory menu.
3. Move the cursor to “ADC ADJUST” and press OK to enter the sub-menu.
4. Input YPbPr signal (VG-848 Timing:978(483P), Pattern:984 SMPTE Color Bar). Move the cursor to “mode”, press CH+ and CH- to select “YPbPr(HD)”, move the cursor to “AUTO ADC” and press ENTER to adjust automatically till complete.
5. Input YPbPr signal (VG-848 Timing:978(483P), Pattern:984 SMPTE Color Bar). Move the cursor to “mode”, press CH+ and CH- to select “YPbPr(SD)”, move the cursor to “AUTO ADC” and press ENTER to adjust automatically till complete.

• White balance adjustment.

1. The default of color temperature of COOL is 12000K and the coordinate is (272, 278); color temperature of NORMAL is 9300K and the coordinate is (285,293), color temperature of WARM is 6500K and the coordinate is (313,329).

• Adjustment steps.

1. Before the white balance adjustment, please let the unit working at least 30 minutes and at a stable situation, use BBY channel of the white balancer CA-210.
2. Switch to HDMI channel.
3. Press” SOURCE”, then press “2, 5, 8, 0” in turn to enter the level one factory menu.
4. Move the cursor to “W/B ADJUST” and press OK to enter the sub-menu.
5. Input DVI/HDMI signal 1024X768/60Hz 16 step Gray (Timing:856, Pattern:921). Move the cursor to “MODE”, press CH+ and CH- to select “HDMI” or other HDMI channel, move the cursor to “TEMPERTURE” and press CH+ and CH- to select “COOL”.
6. Fix G GAIN, adjust R GAIN, B GAIN and let the color coordinate of the fourteenth scale be (272,278).
7. Fix G OFFSET, adjust R OFFSET, B OFFSET and let the color coordinate of the third scale be(272,278).
8. When adjusting, please keep the color temperature of high light to be X=272±5, Y=278±5 and the low light to be X=272±8, Y=278±8.
9. Move the cursor to “COPY ALL” and copy the data to the other channels.
10. Check if the color temperatures of NORMAL and WARM are up to the mustard (low light acceptable error:±8, high light acceptable error:±5), if not, adjust R-GAIN/ B-GAIN/ R-OFF/ B-OFF.
11. Check the color temperature of COOL, NORMAL and WARM of other channels (ANALOGTV, DVB-T, Video, YPbPr,VGA), if they are not up to the mustard then adjust and store the data separately.

The reference of adjustment rule is below:

• B gun: lower B gun to increase X, Y coordinate data, while raise B gun to decrease the data.
• R gun: raise R gun to increase X coordinate data, while lower R gun to decrease the data; (R gun adjustment will affect X and Lv slightly).
• G gun: raise G gun to increase Y coordinate data, while lower G gun to decrease the data; (G gun adjustment will affect Y and Lv greatly).

Performance check

TV function:

• Connect RF to the center signal source, enter Channel menu → auto search, check if there are channels be skipped, check if the picture and speaker are normal.

AV/S-Video terminals:

• Input AV/S-Video signal, check if the picture and sound are normal.

YPbPr/YcbCr terminal

• Input YUV signal (VG848 signal generator), separately input the YUV signals listed in table3 and check if the display and sound are normal at any situation (power on, channel switch and format convert, etc.).