SONY KF-42SX200 - 42SX200K - 42SX200U - PROJECTOR ENGINE ADJUSTMENT METHOD

Operation Method for Projector Engine Adjustment

• Enter the Service menu, and select “Device Register Setting”  à “Projector Engine”.
• Press “1” or “4” button on the commander to select the item, and press “3” or “6” on the commander to change the data.
• Before returning to the Service menu, press “ (MUTE)” +“0” buttons on the commander to write the data.  (Omission of this operation causes the set data to be returned to the data before adjustment)
• Press “MENU” button on the commander to return to the Service menu.

How to Enter TT Mode

• Turn on the main power switch to place this set in standby mode. (LED will light in red.)
• Press the buttons on commander as follows, and the TT mode will be selected.

[ON SCREEN DISPLAY BUTTON à [5] à VOLUME [+] à TV MODE ]  à ENTER TT MODE.

• “TT - -” will appear in the top right corner of the screen. Other status information will also be displayed.
• If “ (TV MODE)” button or “0” + “0” button is pressed, the set exits from the TT mode and returns to normal TV mode.

SONY KF-42SX200 - 42SX200K - 42SX200U - ERROR DETECTION MONITOR & ERROR READER DISPLAY - SERVICE MODE - TT MODE

ERROR DETECTION MONITOR

Device acknowledge is used to check IIC errors.

Each device is checked three times, if there is no acknowledge after every attempt, it will be regarded as an error.

There are three step to check errors.

1. Error Monitor Menu
2. Error Reader.

The error monitor menu is displayed by selecting Service Mode : Monitoring. The following menu will be displayed

Error Monitor
1	Ignore Errors	OFF	ON	ON
Operating Time :		000021 h 40 min
Stored Errors :
1. J-B MSP3411G
2. B3-B CXA2101 MCP
3. J-B CXA2123 Main Col Dec
4. Error Code Not Valid
5. Error Code Not Valid Current Error :
Start Error Sequence

Error Monitor
1          LAMP	0
5          LAMP DRIVER	0
4          FAN	0
3          LAMP COVER             WDT-E	1 0

Error Reader Display

• The error reader display is connected to the service connector to read actual error codes.
• Once an error has been detected it will then be displayed on the two digit error reader. The errors displayed refer to the following table

	Send Data to  Error	Reader
Error Code	Data High	Data Low	Error Type	Function
00 00h	----	f0h	no device
Gen. IIC Error
00 01h	f0h	01h	IIC 0 line
00 02h	f0h	02h	IIC 1 line	not used
Device Error
A Board
01 01h	f1h	01h	CXA1875	Port Expander
01 02h	f1h	02h	TU1301	Main Tuner
01 03h	f1h	03h	TU1302	Sub Tuner
BB Board
04 01h	f4h	01h	CXD9509	MID-X
BB Board
06 01h	f6h	01h	CXA2101	MCP
J Board
04 04h	f4h	04h	TDA9178	Picture Booster
07 03h	f7h	03h	CXA2123	Sub Colour
07 04h	f7h	04h	CXA2123	Main Colour
07 0Ah	f7h	0Ah	CXA2149	AV SW
S Board
07 08h	f7h	08h	MSP3411G	Sound Proc
M Board
08 01h	f8h	01h	M24C32	NVM

How to Enter Service Menu

Select TT mode.

• Press “MENU” button on the commander once, and normal menu screen will appear, or press it once more, and the following service menu screen will appear.

===========================================

Service AE5(A)

Initialising

Reset Devices

Monitoring

Device Register Setting

Special Adjustment

Select : UP / DN  Next menu : RIGHT

===================================

• Following the screen, press [UP] or [DN]  on the joystick to select the desired item, and press [>] key to enter the selected item.
• Press [UP/DN] on the joystick to change data of each item, and press “ (OK)” button to write changed data. (Except Projector Engine mode)
• To return from each item, press [<] key on the joystick. Or, to return to the TT mode, press the “MENU” button. (Except Projector Engine mode)

TEST-TEST MODE

• Is available by pressing “OSD”, “5”, “Volume +”, “TV” button in the standby mode, OSD “TT--”appears.

The diagnosis menu can be displayed by these methods :

• TT mode : Press “33”
• Service Menu : Monitoring  à Error Monitor or
• LCD-Engine Error Menu.

For correction of any wrong input (first digit.) by mistake these methods are possible :

• Press“- -”
• Press“0”

The Test-Test Mode can be left by these methods :

• Press“0” twice.
• Press TV button
• Press standby button.

SONY KF-42SX200 - 42SX200K - 42SX200U [REMOTE CONTROL RM-905] PROJECTION TV – BLINKING CODES – SELF DIAGNOSTIC FUNCTION

Lamp: LAMP [0A-1484-885-A LAMP BLOCK ASSY]

SELF DIAGNOSTIC FUNCTION
     The identification of errors within the LE-3A chassis is triggered in one of two ways : - 1: Busy or 2: Device failure to respond to IIC.  In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant device number will be displayed through the LED (Series of flashes which must be counted) non fatal errors are reported using this method.

Diagnostic Item Description	No. of times Standby LED Flashes	Probable cause Location	Detected Symptoms
Power does not turn on	Does not light	Power cord is not plugged in Fuse is Burned out	Power does not come on No power is supplied to the TV AC power supply is faulty
SET 5V Down	2 times	Q1606, 1607 Power FET is shorted [G-Board]	Power does not come on Load on power line has shorted

ERROR CODES [LED BLINKING CODES]

ERROR	STBY LED ERROR COUNT
No error	00
Not allowed (may be confused with Sircs response flash)	01
SET 5V Down	02
Lamp Cover error	03
Fan error	04
Lamp Driver error	05
Not used	06
Speaker Protection	07
General IIC Line 0 error	08
MEGATEXT (IC9502)	09
NVM (IC9108)	10
Main colour decoder (IC8301)	11
MCP (IC701)	14
Multi sound processor (IC4702)	15
Auto Wide (IC8700)	16
External RAM (IC9107)	17
Lamp error	Lamp LED continually on

HOW TO ENTER SERVICE MODE TO BANG & OLFUSEN - CHANGHONG - CROWN & BLACK DIAMOND TVs

Bang & Olufsen TV model LX4500, LX5500, LX5000, and LX6000

• Power ON the TV.
• Press TV on remote control and short the pin service mode plugged p700 on PCB14.
• Select press p+/p- button and change value pres v+/v- button.
• Save change and exit press STOP button on remote control.

CHANGHONG 21BM91

• To enter the DESIGN/SERVICE mode Set the volume to no sound.
• Then press and hold the MUTE button on the remote control, and press the MENU button on the TV to enter the factory mode.
• Red “S” is displayed on the upper center of the screen indicating that the TV is in service mode.
• To exit from the S mode, turn off the TV set by the POWER button on the remote control. 

CROWN CM-2007

• Open the remote, removing the top cover.
• Use the keys that have no access External and under "previous channel" and "Sound." Canal + / - Select the item with the VOL + / - adjusts its value. 

BLACK DIAMOND BDS1451UK

• To enter Black Diamond TV factory mode press Menu and press following key 4, 7, 2, 5.
• Factory mode load in 0.1 second,
• Use Red, Green, Blue, Yellow button to select and change.
• Save settings press Ok button.
• To exit from factory mode press MENU button.