Sunday, April 30, 2017

715G5804PSU SCHEMATIC – Used with Philips, Vizio and AOC LED TVs

AOC - LE20A1140; LE22A1331 / 61; LE23A6330 / 61; LE24A1332 / 61; T2369M; T2369Z; T2265WM
PHILIPS - 23PFL5130 / T3; 23PFL5530 / T3
Vizio - E221-A1, E241i-A1 
Used ICs: PF6200, STF6N65K3 (switching output), PS2561DL1—1 (opto-coupler), AO4486, PF7001S
Main SMPS
LED driver (back-light inverter)
PWB
Click on the pictures to magnify

Friday, April 28, 2017

My service table today - Philips 21PT5437 – dead – TDA4864 Vertical scan output – No blinking indications

Philips 21” flat CRT TV – received for repair in dead condition.  Vertical scan output IC used is TDA4864
Set condition: Dead.
The party informed that the set went dead while watching a program.  Before going dead; the picture shrunk vertically at about 4” width across the raster; (a horizontal belt), then turned to a horizontal thin line across the center of the screen, and finally it has switched Off by itself.  After that, the set won’t switch On at all.
They also said this is the fourth time; the failure of this type occurs for this set within a month time.  Each time they called the technician at home and he has replaced some components and it was worked gain.
It was clear that the party might have lost their trust with the technician, and brought it at my service center.  Whatever it may be.  let me check the set.
I opened the back cover.  Looked at the circuit board for any visual damage to any of the component/s.  Nothing found damaged.checked the AC mains fuse.  OK.  Shouldn’t be no fault with SMPS supply circuit.
Plugged the set to AC line.
While looking at the front panel Power LED, switched the set ON, by its main power ON/OFF switch, at its front panel.
The power LED lighted for some seconds, and went OFF.  No blinking indications.
It is clear that there should be some short circuit at the main board.  Almost all Philips circuits will have a short circuit protection circuit (built in) which will make shut down the SMPS circuit; if any short circuit has detected by the main system control IC.
Switched OFF the AC mains switch.  Unplugged the AC chord from the wall socket.
Measured if there is any storage voltage retains in the DC main reservoir capacitor.  No storage voltage detected.
Now it is safe to use the multitester; to measure the characteristic of component/s.
How to go forward?  From where should I begin?
I did recall the fault information from the party.  From it, was clear that as they noticed a horizontal bar, and then a thin horizontal line along the middle of the screen.  If so, the fault should be at or around the vertical scan output section circuit.
In case of Philips circuits, the replacement component/s should be the exact number that they have used in their circuit board, otherwise the service work will fail; no doubt.  I’ve many previous service experiences. I did a visual check on the vertical scan output IC.  The IC is found bulged [broken] at its center part.  See the picture.
Clear that it has damaged. I did notice, there are some aluminum folding (screwed along with the heat sink of the IC.)
It was clear that the previous technician might have noticed an overheating with this IC; and to prevent it; he have fitted these extra pieces of aluminum.
If so, what make the IC overheat?  3 possibilities are there.
1] Overvoltage (110VDC) from the SMPS output.
2] Winding short at the vertical scan section winding at the deflection yoke.
3] the IC number replaced might be different.
Here I have to make sure about which IC was used by Philips to this particular model. 
I de-soldered out the damaged IC.  Checked its number. 
The replaced one is “TDA4864J”
I know, this IC number has 2 versions. “TDA4864J & TDATDA4864AJ”
Both of them are used at vertical scan output section circuit by Philips.  Both the number can be used, but should make some circuit alterations.  Let me explain.
Look at these circuits [typical vertical scan output circuits used by both versions of this IC by Philips]
CLICK ON THE SCHEMATICS TO ZOOM
1)With CS2 (typical value between 47 and 150 nF) the flyback time and the noise behaviour can be optimized.
2) With R5 capacitor CF will be charged during scan and the value (typical value between 150 and 270 Ω) depends on Idefl, tflb and CF.
3) R6 reduces the power dissipation of the IC. The maximum possible value depends on the application.
I did compare the present circuit on board.  It was clear that the circuit is configured for TDA4864AJ.
Double checked the circuit.  Yes.  I’m correct.
It is sure that the fault lies here.  Instead of TDA4864AJ, the previous technician replaced TDA4864J. 
Now I have to make sure that there is no other short circuit at the main board.
Please recall; now there is no vertical scan output IC on board, as I’ve de-soldered it out from the circuit earlier.
Here is another culprit.
For almost all Philips digital TV circuits, the set won’t switch On, without vertical scan output signal.
I did plug the set, and switched it ON; without the vertical scan output IC at slot.
The power LED began to light up; and remain lighted.  It does not go OFF.
If the set is in perfect working condition; this LED will light up fitst; within seconds it will go Off and the raster will appear simultaneously; and the set will work perfectly.  Here the LED remain ON, because there is no vertical scan output signal present due to the absence of TDA4864AJ.
Switched Off the set. Checked all the components connected to TDA4864 terminals for any damage. Nothing fond abnormal.
Yet, I replaced the 3Nos Electrolytic capacitors used at this section, as a precautionary measure.
Replaced the IC TDA4864AJ from my service stock components.
Screwed out all the extra heatsink fins used by the previous technician.
Once again checked all the component/s around the TDA4864AJ.
Plugged the set to AC mains, and switched it ON.
Ahh!!
The set works fine.
Kept at this condition for about an hour.  Checked the heat of the TDA4864AJ periodically.
The temperature raised to 40 to 45 degree C and remain noconstant.
No overheating, a moderate heat, and it remain stationary.
MY WORK FOR TODAY IS OVER
Let me relax for a while.
Have a good day to all.
  Both the TDA4864J and TDA4864AJ consist of a differential input stage, a vertical output stage, a flyback generator, a reference circuit and a thermal protection circuit.
The TDA4864J operates with a separate flyback supply voltage while the TDA4864AJ generates the flyback voltage internally by doubling the supply voltage.
Differential input stage
  The differential sawtooth input current signal (coming from the deflection controller) is connected to the inputs (inverted signal to pin INN and non-inverted signal to pin INP). The vertical feedback signal is superimposed on the inverted signal on pin INN
Vertical output and thermal protection
  The vertical output stage is a quasi-complementary class-B amplifier with a high linearity.  The output stage is protected against thermal overshoots.
For a junction temperature Tj > 150 °C this protection will be activated and will reduce then the deflection current (IV-OUT).
Flyback generator
  The flyback generator supplies the vertical output stage during flyback.
The TDA4864J is used with separate flyback supply voltage to achieve a short flyback time with minimized power dissipation.
  The TDA4864AJ needs a capacitor CF between pins VP3 and VP2 (see Fig.2). Capacitor CF is charged during scan, using the external diode D1 and resistor R5.
During flyback the cathode of capacitor CF is connected to the positive supply voltage and the flyback voltage is then twice the supply voltage. For the TDA4864AJ the resistor R6 in the positive supply line can be used to reduce the power consumption.
In parallel with the deflection coil a damping resistor RP and an RC combination (RS1 = 5.6 Ω and CS1 = 100 nF) are needed. Furthermore, another additional RC combination (RS2 = 5.6 Ω and CS2 = 47 to 150 nF) can be used to minimize the noise effect and the flyback time.

Friday, April 21, 2017

Thomson and TCL LED TV How to enter service mode, software update, Power and backlight inverter circuit diagram

How to enter service mode, software update, Power and backlight inverter circuit diagram Thomson and TCL LED TV  Echom 19AE, Echom 22AE and Echom 23AE [19, 22 and 23 inch LED TVs)
Thomson T19E27U, ThomsonTLC MT27S-AP
TCL MT27S-AP, TCL T19, TCLT22, TCL T24E27, TCL T29V
Factory Menu covers all indispensable functions during manufacture such as White Balance Adjustment, Shop Init, NVM  reset,DesignMenu1,DesignMenu2 e.g., while the items under DesignMenu1 and DesignMenu2 is exclusively used by R&D engineer, anyone else shouldn’t change the settings in the menu. When you wish to learn the product information like project ID, model name, you can access to
DesignMenu1. In addition, in Hotel Menu, we also provide a great deal of useful functions for specific applications in hotel.
Factory Menu
Accessing
a. In the first place, press Menu button of remote control, then select Contrast item of Picture submenu. 
Finally, press 9, 7, 3, 5 consecutively.
b. When the FAC HOTKEY item of Factory Menus enabled (ON), press Return button of remote control.
HOTEL MENU
Accessing
a. Hotel Menu(enable)item is enabled(on)
b. press Menu button of remote control, then select Contrast item of Picture submenu. Finally, press 9, 7, 1, 5 consecutively.
The steps of debugging
Device
Color Analyzer CA-210. 
Video Pattern Generator Chroma2329. 
Color TV Pattern Generator PM5418, VGA cable, AV cable(RCA),YPBPR(RCA) cable.
Chroma2329 Fluke5418 CA-210
Steps of debugging [Troubleshooting]
According to the requirement of order take the below steps to finish the appropriate settings.
A enter the Factory Menu, enable HOTKEY
B Check the version of software, release date displayed at the bottom of Factory Menu. If the information is correct, you can ignore step C and D.
C Enter Factory Menu, choose DESIGNMENU1->PROJECT ID, choose corresponding Project ID number of the product.
D Return to DesignMenu1, check the Product model.
E Choose Factory Menu-> NVM RESET and press and wait until prompt OK appears.
F Restart the set
G According to the requirement of order, set the items of Hotel Menu etc.
H After aging under normal temperature, adjust white balance.
I Choose Factory Menu > SHOP INIT and press button of remote control to initialize the set.
Note: after step I (execute SHOP INIT), Hotel Menu will be disabled by default.
Therefore, if order requires hotel function, it is necessary to enable hotel function by set Factory Menu > DesignMenu2 >HOTEL MENU ENABLE to ON
White Balance adjustment (Manual)
Before adjustment, you must ensure Color Analyzer has been calibrated. Only AV1, YPBPR, VGA , HDMI 1 need to be adjusted. It is necessary to adjustment HDMI 1 first.
Signal and generator
The pattern of the signal should be used are White (Chroma2329 pattern113) and Grey (pattern 114).The format of signal are respectively 720p for HDMI1 (Chroma2329 Timing 69), NTSC for AV1 (Chroma2329 Timing 37),1024×768@60Hz
Steps of adjustment
1) enter the factory menu->WB, select source HDMI 1 and COLORTEMP normal.
2) input white signal in 720p format
3) change R Gain and B Gain to make sure the value of color coordination equal to (x, y)
In addition to select COLORTEMP COOL/WARM, the adjustment method of COOL and WARM color temperature is same with that of NORMAL.
Chip list of software programming before SMT
Following chip must be programmed before SMT by ALL-11 or other tools.
1 U401 Flash  W25Q32 -13-W25Q32-BVB  Main software;HDMI KEY;EDID SO-8
Note
1) The software for U401 can be program using ISP tool.
2) Every set has its unique HDCP key which is purchased from suppliers or HDCP certification authority. Check HDCP function in the process of production.
3) Once in a while, the software of main board may be upgraded. Please pay attention to use the latest software before production.
SMPS and BackLight inverter schematic
Software upgrade through USB disk
1) Please ensure the software you are using has a correct file name TCL_MT27_UPDATE.bin, then copy it to the root directory of a USB disk.
2) Insert the USB disk to the USB socket of the set for which you are going to upgrade program.
3) Enter the Factory Menu (you can choose either a or b way below)
a. In the first place, press Menu button of remote control, then select Contrast item of Picture submenu. Finally, press 9, 7, 3, 5 consecutively.
b. When the Factory hotkey item of Factory Menu is enabled (ON), press Return button of remote control.
4) Select USB UPG item of DesignMenu2 submenu, press buttonof remote control, a pop menu will appear prompting whether start upgrade or not. Press Yes to start upgrade, press No to cannel. 
Wait patiently until the set restart automatically after upgrade.
Do not cut off the power supply during the process.
Check software version, release date and Project ID
After upgrading, sometimes you may not certain whether the new software has been successfully updated or not. In this case, you can check the software version and release date in Factory Menu to make sure the success of upgrading. In addition, for the convenience of software management, many models of same chassis may share a same software, but are allocated with different Project ID.
In another words, every model has its unique Project ID. 
Obviously, Both software version and Project ID are highly critical to ensure the set work properly. Therefore, after upgrading software, it is recommended  you to check these information by following method.
1) Enter the Factory Menu (you can choose either a or b way below)
a In the first place, press Menu button of remote control, then select Contrast item of Picture sub-menu. Finally, press 9, 7 3, 5 consecutively.
b. When the HOTKEY item of Factory Menu is enabled (ON), press Return button of remote control.
2 Check the version of software, release date displayed at the bottom of Factory Menu. If the information is correct, you can ignore step 3.
3 Choose DesignMenu1->PROJECTID, choose corresponding Project ID number of the product (Please refer to the description in BOM about Project ID number).
4 Choose Factory Menu and press OK button of the remote. Next, select NVM RESET and press and wait until prompt OK appears.
Choose SHOP INIT and press button of remote control to initialize the set.
Note: after step I (execute SHOP INIT), Hotel Menu will be disabled by default
Therefore, if order requires hotel function, it is necessary to enable hotel function by set Factory Menu > DesignMenu2 > HOTEL Menu enable to ON.
6) Restart the set.
If the resolution of the panel of your set is 1366×768(HD panel), you can press 062598,Menu, and Number(HD panel projectID) of remote control in series after turning on.
If the resolution of the panel of your set is 1920×1080(FHD panel), you can press 062598,Menu, and Number(FHD panel projectID) in series after turning on.
If you can see the picture at this time, please recheck the project ID again. If the project ID is still wrong, correct it reference to above description.

Toshiba 15SLDT1Combination 15 LCD TV and DVD Video Player Password reset, Firmware update, Language change,

Toshiba 15SLDT1TV/DVD Combination  How to take out disc at emergency, How to update the DVD firmware, SMPS and Backlight inverter schematic, Forget password, change the language and more:
PAL UK, IR, CCIR, FRENCH System, B/G, D/K, I/I, L
AV Input receivable: NTSC 3.58, NTSC 4.43/PAL 60
RE-WRITE FOR DVD FIRMWARE
Turn on the power, and set the DVD mode.
Confirm that the "No Disc" will be appeared on the screen.
Press both VOL. DOWN button on the set and Channel button (5) on the remote control for more than 2 seconds.
Press VOL. UP/DOWN button on the unit to check if all the keys on the unit do not function.
NOTE: To check if DVD Write mode is set.
When inserting Up-date Disc at Non DVD Write mode, the read error will happen.
Insert the Up-date Disc.
Automatic read will start and "Firmware upgrade Please Wait" will be displayed on the screen.
At this time, the horizontal noise lines may appear. But no problem.
NOTE: Do not turn off the unit on the way or operate the keys on the unit and remocon.
Up-Date error will happen and cannot be done with the Up-date of Update Disc.
After the Up-date, Logo screen will appear.
Unplug the AC cord, and then plug it in.
After the write, set to the initializing of shipping.
Turn on the power, and set the DVD mode.
Press both VOL. DOWN button on the set and Channel button (4) on the remote control for more than 2 seconds.
The "INITIALIZE 5 > COMPLETE" will appear on the screen.
Then unplug the AC cord, and plug it in.
CHECK FOR THE FIRMWARE VERSION
Turn on the power, and set the DVD mode.
Press both Channel button (1) on the remote control and the STOP button on the set for more than 2 seconds.
Firmware version will be displayed on the top left of the screen.
Turn off the power.
WHEN REPLACING EEPROM (MEMORY) IC
CONFIRMATION OF CHECK SUM, POWER ON TOTAL HOURS AND MICON VERSION
Initial total of MEMORY IC, POWER ON total hours and MICON VERSION can be checked on the screen. 
Total hours are displayed in 16 system of notation.
WHEN REPLACING EEPROM (MEMORY) IC
If you set a factory initialization, the total hours is reset to "0"
Turn on the POWER, and set to the TV mode.
Set the VOLUME to minimum.
Press both VOL. DOWN button on the set and Channel button (2) on the remote control for more than 2 seconds.
After the confirmation of each check sum, turn off the power.
[The each item value might be different according to each set]
CONFIRMATION OF INITIAL DATA
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings.
Turn on the POWER, and set to the TV mode.
Set the VOLUME to minimum.
Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds.
ADDRESS and DATA should appear
[No need set data other position than 0D00~0E3F and 1900~7FFF]
ADDRESS is now selected and should "blink". Using the UP/DOWN button on the remote, step through the ADDRESS until required ADDRESS to be changed is reached.
Press RIGHT/LEFT button to select DATA. When DATA is selected, it will "blink".
Again, step through the DATA using UP/DOWN button until required DATA value has been selected.
Pressing RIGHT/LEFT button will take you back to ADDRESS for further selection if necessary.
Repeat steps 4 to 6 until all data has been checked.
When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
After the data input, set to the initializing of shipping.
Turn on the POWER.
Set the VOLUME to minimum.
Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 2 seconds.
After the finishing of the initializing of shipping, the unit will turn off automatically.
The unit will now have the correct DATA for the new MEMORY IC.
SMPS and Back-light inverter schematic
Parental control setting
Some discs are specified as not suitable for children.  Such discs can be limited not to playback with the unit.
1) Press C or D to select “Parental”, then press ENTER. “Enter Password” screen will appear.
2) Press “0000” using Number buttons (0–9).  (Note, this is pre-setting password of this unit). Then press ENTER. The parental level list will appear.
> Level Off: The parental control setting does not function.
> Level 8: Virtually all DVD software can be played back.
> Level 1: DVD software for adults cannot be played back.
3) Press C or D to select from the level 1 to level 8.
The limitation will be more severe as the level number is lower. 
Then press ENTER.
Notes:
* Depending on the discs, the unit cannot limit playback.
* Some discs may not be encoded with specific rating level information though its disc jacket says “adult.” For those discs, the age restriction will not work.
> The password is required every time when you change the parental level.
> If you input a wrong number, press CANCEL.
To Set a new password
1) Press C or D to select “Password”, and then press ENTER. “Enter Current Password” screen will appear.
2) Press Number buttons (0–9) to input the current password (If the password has not been set yet after you purchase this unit, it is “0000”).
3) Then press ENTER. “Enter New Password” screen will appear. Press Number buttons (0–9) to input the new password.
4) Press ENTER. Now your new password has been set. Be sure to remember this number.
If you forget the password.
1) Press EJECT to remove the disc.
2) While holding 7 down on the remote control and at the same time press STOP on the side panel. “Password Clear” appears on the screen. 
Now the password has been returned to the initial value (“0000”).
DivX(R)VOD
In order to play DivX® VOD (Video On Demand) content on this unit, you first need to register the unit with your DivX® VOD content provider. You do this by generating a DivX® VOD registration code, which you submit to your provider.
Press C or D to select “DivX(R) VOD”.
Then press ENTER.
Your 8-character registration code is displayed. Make a note of the code as you will need it when you register with a DivX® VOD provider.
Then press ENTER.
Language code list
Enter the appropriate code number for the initial setting "Menu:, Subtitle and/or Audio
Abkhazian 1112 Fiji 1620 Lingala 2224 Singhalese 2919
Afar 1111 Finnish 1619 Lithuanian 2230 Slovak 2921
Afrikaans 1116 French 1628 Macedonian 2321 Slovenian 2922
Albanian 2927 Frisian 1635 Malagasy 2317 Somali 2925
Amharic 1123 Galician 1722 Malay 2329 Spanish 1529
Arabic 1128 Georgian 2111 Malayalam 2322 Sundanese 2931
Armenian 1835 German 1415 Maltese 2330 Swahili 2933
Assamese 1129 Greek 1522 Maori 2319 Swedish 2932
Aymara 1135 Greenlandic 2122 Marathi 2328 Tagalog 3022
Azerbaijani 1136 Guarani 1724 Moldavian 2325 Tajik 3017
Bashkir 1211 Gujarati 1731 Mongolian 2324 Tamil 3011
Basque 1531 Hausa 1811 Nauru 2411 Tatar 3030
Bengali; Bangla 1224 Hebrew 1933 Nepali 2415 Telugu 3015
Bhutani 1436 Hindi 1819 Norwegian 2425 Thai 3018
Bihari 1218 Hungarian 1831 Oriya 2528 Tibetan 1225
Breton 1228 Icelandic 1929 Panjabi 2611 Tigrinya 3019
Bulgarian 1217 Indonesian 1924 Pashto, Pushto 2629 Tonga 3025
Burmese 2335 Interlingua 1911 Persian 1611 Turkish 3028
Byelorussian 1215 Irish 1711 Polish 2622 Turkmen 3021
Cambodian 2123 Italian 1930 Portuguese 2630 Twi 3033
Catalan 1311 Japanese 2011 Quechua 2731 Ukrainian 3121
Chinese 3618 Javanese 2033 Rhaeto-Romance 2823 Urdu 3128
Corsican 1325 Kannada 2124 Romanian 2825 Uzbek 3136
Croatian 1828 Kashmiri 2129 Russian 2831 Vietnamese 3219
Czech 1329 Kazakh 2121 Samoan 2923 Volapük 3225
Danish 1411 Kirghiz 2135 Sanskrit 2911 Welsh 1335
Dutch 2422 Korean 2125 Scots Gaelic 1714 Wolof 3325
English 1524 Kurdish 2131 Serbian 2928 Xhosa 3418
Esperanto 1525 Laothian 2225 Serbo-Croatian 2918 Yiddish 2019
Estonian 1530 Latin 2211 Shona 2924 Yoruba 3525
Faroese 1625 Latvian, Lettish 2232 Sindhi 2914 Zulu 3631
DISC REMOVAL METHOD AT NO POWER SUPPLY
Remove the Back Cabinet and Angle Deck. (Refer to item 1 of the DISASSEMBLY INSTRUCTIONS.)
Slide the Belt Loading toward the arrow direction by hand to release the lock.
Take out the Disc from the DVD Deck. Be careful not to scratch on the Disc.
TRAY LOCK
The disk cannot be taken out by setting the tray Lock,  follow the steps below.
Turn Unit ON.
Set the DVD to the Stop Mode.
Press it in order of “SETUP”, “SUBTITLE”, “3”, “AUDIO SELECT”and “0” key of a remote control unit.
The On Screen Display message “ ” will appear.
The Tray Lock has now been set up.
To unlock the Tray Lock, please follow the steps below.
Turn Unit ON.
Set the DVD to the Stop Mode.
Press it in order of “SETUP”, “SUBTITLE”, “3”, “AUDIO SELECT” and “0” key of a remote control unit. (Without its original remote control, these adjustments cannot be done.)
The On Screen Display message will appear.
The Tray Lock has now been cleared.
REMOVAL OF DVD DECK PARTS
Disassemble only the DVD DECK PARTS listed here. Minute adjustments are needed if the disassembly is done. If the repair is needed except listed parts, replace the DVD MECHA ASS'Y
TRAVERSE ASS'Y
Remove the 3 screws (1).
Unlock the 2 supports (2).
Remove the Insulator (R) from the Loader Sub Ass'y.
Remove the Traverse Ass'y.
[In case of the Traverse Ass'y installation, hook the wire on the Loader Ass'y]
SWITCH PCB ASS'Y/GEAR MIDDLE/GEAR FEED/RACK FEED ASS'Y/FEED MOTOR
Remove the Insulator (F).
Remove the Insulator (R).
Unlock the support (1).
Remove the Gear Middle.
Remove the screw (2).
Remove the Rack Feed Ass'y.
Remove the screw (3).
Remove the Switch PCB Ass'y.
Remove the screw (4).
Remove the Gear Feed.
Remove the 2 screws (5).
Remove the Feed Motor.
Remove the Gear Motor
If a non-compatible disc is loaded, “Incorrect Disc”, “Region Code Error” or “Parental Error” will appear on the TV screen according to the type of loaded disc. In this case, check your disc again.
* Some discs may take a minute or so to start playback.
* When you set a single-faced disc label downwards (i.e. the wrong way up), “Reading” will appear on the display for a few minutes and then “Incorrect Disc” will continue to be displayed.
* Some discs may not work the resuming facility.
* Resuming cannot function when you play a PBC-featured Video CD while the PBC is on. To turn off the PBC.
* Some playback operations of DVDs may be intentionally fixed by software producers. Since this unit plays DVDs according to the disc contents the software producers designed, some playback features may not be available. Also refer to the instructions supplied with the DVDs.
* Do not move the unit during playback. Doing so may damage the disc.
* Use the EJECT button to unload and eject the disc.
* Do not put any objects other than discs on the disc slot. Doing so may cause the unit to malfunctions.
* In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an on-screen menu may damage your television set, permanently etching that image onto its screen. To avoid this, be sure to press (On/Standby) on the remote control once the movie is completed.
* There may be a slight delay between the button is pressed and the function activates.
To obtain a higher quality picture
Occasionally, some picture noise, not usually visible on the TV screen during a normal broadcast, may appear while playing a DVD video disc. It is due to high resolution pictures on these discs which include a lot of information. The amount of noise depends on the TV you use with this unit. You should generally reduce the sharpness adjustment on your TV when viewing DVD video discs.

Tuesday, April 18, 2017

Samsung LED TV UA32F4100, UA32F5300 How to upgrade firmware, Connector voltages and details, Disassembly

Samsung LED TV UA32F45*0A*, UA**F53*0A*, UA**F55**A*, UA32F4100
Troubleshooting
1. Check the various cable connections frst.
- Check to see if there is a burnt or damaged cable.
- Check to see if there is a disconnected or loose cable connection.
- Check to see if the cables are connected according to the connection diagram.
2. Check the power input to the Main Board.
3. How to distinguish if the problem is caused by Main Board or T-Con Board.
No Video: If the problem is No Video but BLU is on and Indication LED is blinking repeatedly and faster than normal booting, replace the T-Con Board.
Distorted Picture: Check the inner patterns.
How to check inner pattern
1. Factory mode. (Mute > 1 > 8 > 2 > Power on;  when TV is in ‘stand-by mode’)
2. Move to SVC menu.
3. Move to Test Pattern.
4. Check inner patterns
Method of Color Calibration (AV)
1. Apply the NTSC Lattice (N0. 3) pattern signal to the AV IN 1 port.
2. Press the Source key to switch to “AV1” mode.
3. Enter Service mode.
4. Select the “ADC” menu.
5. Select the “AV Calibration” menu.
6. In “AV Calibration Off” status, press the
key to perform Calibration.
7. When Calibration is complete, it returns to the high-level menu.
8. You can see the change of the “AV Calibration” status from Failure to Success.
Method of Color Calibration (Component)
1. Apply the 720p Lattice (N0. 6) pattern signal to the Component IN 1 port.
2. Press the Source key to switch to “Component1” mode.
3. Enter Service mode.
4. Select the “ADC” menu.
5. Select the “Comp Calibration” menu.
6. In “Comp Calibration Off” status, press the  ►key to perform Calibration.
7. When Calibration is complete, it returns to the high-level menu.
8. You can see the change of the “Comp Calibration” status from Failure to Success.
Method of Color Calibration (HDMI)
1. Apply the 720p Lattice (N0. 6) pattern signal to the HDMI1/DVI IN port.
2. Press the Source key to switch to “HDMI1” mode.
3. Enter Service mode.
4. Select the “ADC” menu.
5. Select the “HDMI Calibration” menu.
6. In “HDMI Calibration Off” status, press the ►key to perform Calibration.
7. When Calibration is complete, it returns to the high-level menu.
8. You can see the change of the “HDMI Calibration” status from Failure to Success.
Adjustment
1. Into the Factory Mode.
2. Select SVC Menu.
3. Select ADC/WB menu.
4. Select White Balance menu.
1. You can adjust the white ratio in factory mode (1:Calibration, 3:White-Balance).
2. Since the adjustment value and the data value vary depending on the input source, you have to adjust these in CVBS,Component 1 and HDMI 1 modes.
3. The optimal values for each mode are configured by default. It varies with Panel’s size and Specification.
• Equipment: CS-210
• Pattern: MIK K-7256 #92 “Flat W/B Pattern" as standard
• Alternate Equipment : CA200& anyone Master supported pattern#92
• Use other Equipment only after comparing the result with that of the Master equipment.
• Set Aging time : 60 min.
Calibration and Manual setting for WB adjustment
• HDMI : Calibration at #24 Chessboard Pattern Manual adjustment at #92 pattern (720p)
• COMP: Calibration at #24 Chessboard Pattern Manual adjustment at #92 pattern (720p)
• CVBS: Calibration at #24 Chessboard Pattern Manual adjustment at #92 pattern (NTSC)
[If finishing in HDMI mode, adjustment coordinate is almost same in AV/COMP mode]
Software Upgrade
Software Upgrade can be performed by downloading the. latest frmware from samsung.com to a USB memory device.
• Current Version - The software already installed in the TV.
Software is represented as ‘Year/Month/Day_Version’.
How to Check the Software Version
Use the Main Menu
1. Click the "MENU" key in remote controller.
2. Select "Support" menu.
3. Locate the menu cursor "Software Upgrade" menu.
4. Click the "INFO" key.
- Check the Main SW and Micom version.
How to Upgrade Software and Micom
Insert a USB drive containing the firmware upgrade downloaded from samsung.com into the TV. Please be careful not to disconnect the power or remove the USB drive while upgrades are being applied. The TV will turn off and turn on automatically after completing the frmware upgrade. Please check the frmware version after the upgrades are complete 
(the new version will have a higher number than the older version). When software is upgraded, video and audio settings you have made will return to their default (factory) settings. We recommend you write down your settings before beginning firmware update. After update is completed, restore your previous settings.
Main Software Upgrade
1. Store the sw program named "T-MST12UABC" in USB memory stick.
- Connect the USB.
2. Click the "MENU" key in Remote Controler.
3. Select "Support" menu.
Locate the menu cursor "Software Update" menu
4. Click the "ENTER" key.
5. Click the "ENTER" key.
- Wait for upgrade complete.
- Check the Software Version.
Power board connector voltages
Connector cables and part numbers
Entering Factory Mode
To enter ‘Service Mode’ Press the remote -control keys in this sequence: 
• If you do not have Factory remote control:
Power OFF
Info
MENU
MUTE
Power On
If you have Factory remote control:
INFO
Factory
[If you don’t have Factory remote control, can’t control some menus]
Initial SERVICE MODE DISPLAY State
Disassembly (Back cover)
Place TV face down on cushioned table
Remove 4 screws from the Stand and R
Remove 15 screws of Rear Cover.
Remove the Cover Jack.
Lift up Rear Cover slightly from the bottom.
Disconnect the Function Assy Cable.
Remove the Rear Cover.

Monday, April 17, 2017

VESTEL Kit-TOSHIBA 20inch TFTLCD TV 20WL56 using– Ics descriptions and features

ICs used:  LM1117, LM2576, LM317T, ST24LC21, TEA5114A, TEA6415, VPC3230D,SDA55XX SDA5550), TPA3002D2, TDA9885/86, TDA1308, PI5V330, GM6015, MST9883, M74HC4052, MC34063, MSP34X0G, DS90C385, NDS8947

20” TFT-LCD TV is a Progressive TV control system based on the µ-controller SDA555X, with built-in deinterlacer and scaler.
TFT TV is a progressive scan flicker free colour television with PC input, driving an WXGA (1366 x 768) panel with 16:9 aspect ratio. The chassis is capable of operation in PAL, SECAM, NTSC (playback) colour standards and multiple transmission standards as B/G, D/K, I/I’, and L/L’. Sound system output is supplying 2x5W (10%THD) speakers. The chassis is equipped with two full SCART’s, one back-AV, one SVHS, one D-Sub 15 (PC) input, one PC stereo audio input and one line out (left and right) and one HP outputs.
IF PART (TDA988X)
The TDA9885 is an alignment-free single standard (without positive modulation) vision and sound IF signal PLL.
The TDA9886 is an alignment-free multistandard (PAL, SECAM and NTSC) vision and sound IF signal PLL demodulator for positive and negative modulation including sound AM and FM processing.  Both devices can be used for TV, VTR, PC and set-top box applications.
MULTI STANDARD SOUND PROCESSOR
The MSP34x0G family of single-chip Multistandard Sound Processors covers the sound processing of all analog TV-Standards worldwide, as well as the NICAM digital sound standards. The full TV sound processing, starting with analog sound IF signal-in, down to processed analog AF-out, is performed on a single chip.
These TV sound processing ICs include versions for processing the Multichannel Television Sound (MTS) signal conforming to the standard recommended by the Broadcast Television Systems Committee (BTSC). The DBX noise reduction, or alternatively, Micronas Noise Reduction (MNR) is performed alignment free. Other processed standards are the Japanese FM-FM multiplex standard (EIA-J) and the FM Stereo Radio standard.
Current ICs have to perform adjustment procedures in order to achieve good stereo separation for BTSC and EIA-J. The MSP 34x1G has optimum stereo performance without any adjustments.
AUDIO AMPLIFIER STAGE WITH TPA3002D2
The TPA3002D2 is a 9-W (per channel) efficient, Class-D audio amplifier for driving bridged-tied stereo speakers. The TPA3002D2 can drive stereo speakers as low as 8 Ω. The high efficiency of the TPA3002D2 eliminates the need for external heatsinks when playing music.
POWER
The LM2576 series of regulators are monolithic integrated circuits ideally suited for easy and convenient design of a step–down switching regulator (buck converter). All circuits of this series are capable of driving a 3.0A load with excellent line and load regulation. Two different versions (one having a fixed output voltage of 3.3 V, and one with 5.0 V) of this IC are used in the regulator board.MICROCONTROLLER SDA55XXGeneral Features• Feature selection via special function register• Simultaneous reception of TTX, VPS, PDC, and WSS (line 23)• Supply Voltage 2.5 and 3.3 V• ROM version is used.External Crystal and Programmable Clock Speed• Single external 6MHz crystal, all necessary clocks are generated internally• CPU clock speed selectable via special function registers.• Normal Mode 33.33 MHz CPU clock, Power Save mode 8.33 MHz
Ports
• One 8-bit I/O-port with open drain output and optional I 2 C Bus emulation support (Port0)
• Two 8-bit multifunction I/O-ports (Port1, Port3)
• One 4-bit port working as digital or analogue inputs for the ADC (Port2)
• One 2-bit I/O port with secondary function (P4.2, 4.3, 4.7)
• One 4-bit I/O-port with secondary function (P4.0, 4.1, 4.4) (Not available in P-SDIP 52)
SERIAL ACCESS CMOS 16K (2048*8) EEPROM ST24C16
The ST24C16 is a 16Kbit electrically erasable programmable memory (EEPROM), organised as 8 blocks of 256*8 bits. The memory is compatible with the I²C standard, two wire serial interface, which uses a bidirectional data bus and serial clock. The memory carries a built-in 4 bit, unique device identification code (1010) corresponding to the I²C bus definition. This is used together with 1 chip enable input (E) so that up to 2*8K devices may be attached to the I²C bus and selected individually.
CLASS AB STEREO HEADPHONE DRIVER TDA1308
The TDA1308 is an integrated class AB stereo headphone driver contained in a DIP8 plastic package. The device is fabricated in a 1 mm CMOS process and has been primarily developed for portable digital audio applications.
SAW FILTERS
K3953M is an IF Filter for Video Applications. The package is SIP5K. Supported standards are B/G, D/K, I, L/L’.
K9656M is an IF Filter for Audio Applications. The package is SIP5K. Supported standards are B/G, D/K, I, L/L’.
LM1117
General Description
The LM1117 is a series of low dropout voltage regulators with a dropout of 1.2V at 800mA of load current. It has the same pin-out as National Semiconductor’s industry standard LM317. The LM1117 is available in an adjustable version, which can set the output voltage from 1.25V to 13.8V with only two external resistors. In addition, it is also available in five fixed voltages, 1.8V, 2.5V, 2.85V, 3.3V, and 5V. The LM1117 offers current limiting and thermal shutdown. Its circuit includes a zener trimmed bandgap reference to as-sure output voltage accuracy to within ±1%. The LM1117 series is available in SOT-223, TO-220, and TO-252 D-PAK packages. A minimum of 10µF tantalum capacitor is required at the output to improve the transient response and stability.
Features
• Available in 1.8V, 2.5V, 2.85V, 3.3V, 5V, and Adjustable Versions
• Space Saving SOT-223 Package
• Current Limiting and Thermal Protection
• Output Current 800mA
• Line Regulation 0.2% (Max)
• Load Regulation 0.4% (Max)
• Temperature Range
— LM1117 0°C to 125°C
LM1117I -40°C to 125°C
Applications
• 2.85V Model for SCSI-2 Active Termination
• Post Regulator for Switching DC/DC Converter
• High Efficiency Linear Regulators
• Battery Charger
• Battery Powered Instrumentation.
LM2576
General Description
The LM2576 series of regulators are monolithic integrated circuits ideally suited for easy and convenient design of a step–down switching regulator (buck converter). All circuits of this series are capable of driving a 3.0 A load with excellent line and load regulation. These devices are available in fixed output voltages of 3.3 V, 5.0 V, 12 V, 15 V, and an adjustable output version. These regulators were designed to minimize the number of external components to simplify the power supply design. Standard series of inductors optimized for use with the LM2576 are offered by several different inductor manufacturers. Since the LM2576 converter is a switch–mode power supply, its efficiency is significantly higher in comparison with popular three–terminal linear regulators, especially with higher input voltages. In many cases, the power dissipated is so low that no heatsink is required or its size could be reduced dramatically.
A standard series of inductors optimized for use with the LM2576 are available from several different manufacturers. This feature greatly simplifies the design of switch–mode power supplies. The LM2576 features include a guaranteed ±4% tolerance on output voltage within specified input voltages
and output load conditions, and ±10% on the oscillator frequency (±2% over 0°C to 125°C). External shutdown is included, featuring 80 mA (typical) standby current. The output switch includes cycle–by–cycle current limiting, as well as thermal shutdown for full protection under fault conditions.
• 3.3 V, 5.0 V, 12 V, 15 V, and Adjustable Output Versions
• Adjustable Version Output Voltage Range, 1.23 to 37 V ±4% Maximum Over Line and Load Conditions
• Guaranteed 3.0 A Output Current
• Wide Input Voltage Range
• Requires Only 4 External Components
• 52 kHz Fixed Frequency Internal Oscillator
• TTL Shutdown Capability, Low Power Standby Mode
• High Efficiency
• Uses Readily Available Standard Inductors
• Thermal Shutdown and Current Limit Protection
• Moisture Sensitivity Level (MSL) Equals 1
LM317T
Description
The LM317T is an adjustable 3 terminal positive voltage regulator capable of supplying in excess of 1.5 amps over an output range of 1.25 to 37 volts. This voltage regulator is exceptionally easy to use and requires only two external resistors to set the output voltage. Further, it employs internal current limiting,thermal shutdown and safe area compensation, making it essentially blow–out proof. The LM317 serves a wide variety of applications including local, on card regulation. This device can also be used to make a programmable output regulator, or by connecting a fixed resistor between the adjustment and output, the LM317 can be used as a precision current regulator.
• Output Current in Excess of 1.5 A
• Output Adjustable between 1.2 V and 37 V
• Internal Thermal Overload Protection
• Internal Short Circuit Current Limiting Constant with Temperature
• Output Transistor Safe–Area Compensation
• Floating Operation for High Voltage Applications
• Available in Surface Mount D2PAK, and Standard 3–Lead Transistor Package
• Eliminates Stocking many Fixed Voltages
ST24LC21
Description
The ST24LC21 is a 1K bit electrically erasable programmable memory (EEPROM), organized by 8 bits. This device can operate in two modes: Transmit Only mode and I2C bidirectional mode. When powered, the device is in Transmit Only mode with EEPROM data clocked out from the rising edge of the signal applied on VCLK. The device will switch to the I2C bidirectional mode upon the falling edge of the signal applied on SCL pin. The ST24LC21 can not switch from the I2C bidirectional mode to the Transmit Only mode (except when the power supply is removed). The device operates with a power supply value as low as 2.5V. Both Plastic Dual-in-Line and Plastic Small Outline packages are available.
• 1 million Erase/Write cycles
• 40 years data retention
• 2.5V to 5.5V single supply voltage
• 400k Hz compatibility over the full range of supply voltage
• Two wire serial interface I2C bus compatible
• Page Write (Up To 8 Bytes)
• Byte, random and sequential read modes
• Self timed programming cycle
• Automatic address incrementing
• Enhanced ESD/Latch up
• Performances
TEA5114A
General description
This integrated circuit provides RGB switching allowing connections between peri TV plug, internal RGB generator and video processor in a TV set.
The input signal black level is tied to the same reference voltage on each input in order to have no differential voltage when switching two RGB generators. An AC output signal higher than 2 Vpp makes gain going slowly down to 0dBto protect the TV set video amplifier from saturation.
Fast blanking output is a logical OR between FB1 (Pin 8) and FB2 (Pin 10).
Features
• 25MHz Bandwidth
• Crosstalk : 55dB
• Short circuit to ground or VCC protected
• Anti saturation gain changing
• Video switching.
TEA6415
General description
The main function of the IC is to switch 8 video input sources on 6 outputs. Each output can be switched on only one of each input. On each input an alignment of the lowest level of the signal is made (bottom of synch. top for CVBS or black level for RGB signals). Each nominal gain between any input and output is 6.5dB. For D2MAC or Chroma signal the alignment is switched off by forcing, with an external resistor bridge, 5 VDC on the input. Each input can be used as a normal input or as a MAC or Chroma input (with external resistor bridge). All the switching possibilities are changed through the BUS. Driving 75Ω load needs an external transistor. It is possible to have the same input connected to several outputs. The starting configuration upon power on (power supply: 0 to 10V) is undetermined. In this case, 6 words of 16 bits are necessary to determine one configuration. In other case, 1 word of 16 bits is necessary to determine one configuration.
Features
• 20MHz Bandwidth
• Cascadable with another TEA6415C (Internal address can be changed by pin 7 voltage)
• 8 Inputs (CVBS, RGB, MAC, CHROMA,...)
• 6 Outputs
• Possibility of MAC or chroma signal for each input by switching-off the clamp with an external resistor
bridge
• Bus controlled
• 6.5dB gain between any input and output
• 55dB crosstalk at 5mHz
• Fully ESD protected
Pinning
1. Input : Max : 2Vpp, Input Current: 1mA, Max : 3mA
2. Data : Low level : -0.3V Max: 1.5V,
High level : 3.0V Max : Vcc+0.5V
3. Input : Max : 2Vpp, Input Current: 1mA, Max : 3mA
4. Clock : Low level : -0.3V Max: 1.5V,
High level : 3.0V Max : Vcc+0.5V
5. Input : Max : 2Vpp, Input Current: 1mA, Max : 3mA
6. Input : Max : 2Vpp, Input Current: 1mA, Max : 3mA
7. Prog
8. Input : Max : 2Vpp, Input Current: 1mA, Max: 3mA
9. Vcc : 12V
10. Input : Max : 2Vpp, Input Current: 1mA, Max : 3mA
11. Input : Max : 2Vpp, Input Current: 1mA, Max : 3mA
12. Ground
13. Output : 5.5Vpp, Min : 4.5Vpp
14. Output : 5.5Vpp, Min : 4.5Vpp
15. Output : 5.5Vpp, Min : 4.5Vpp
16. Output : 5.5Vpp, Min : 4.5Vpp
17. Output : 5.5Vpp, Min : 4.5Vpp
18. Output : 5.5Vpp, Min : 4.5Vpp
19. Ground
20. Input : Max : 2Vpp, Input Current : 1mA, Max : 3mA
VPC3230D
General Description
The VPC 323xD is a high-quality, single-chip video front-end, which is targeted for 4:3 and 16:9, 50/60-Hz and 100/120 Hz TV sets. It can be combined with other members of the DIGIT3000 IC family (such as DDP 331x) and/or it can be used with 3rd-party products.
The main features of the VPC 323xD are
• high-performance adaptive 4H comb filter Y/C separator with adjustable vertical peaking
• multi-standard colour decoder PAL/NTSC/SECAM including all substandards
• four CVBS, one S-VHS input, one CVBS output
• two RGB/YCr Cb component inputs, one Fast Blank (FB) input
• integrated high-quality A/D converters and associated clamp and AGC circuits
• multi-standard sync processing
• linear horizontal scaling (0.25 ... 4), as well as non-linear horizontal scaling ‘Panorama-vision’
• PAL+ preprocessing
• line-locked clock, data and sync, or 656-output interface
• peaking, contrast, brightness, color saturation and tint for RGB/ YC r C b and CVBS/ S-VHS
• high-quality soft mixer controlled by Fast Blank
• PIP processing for four picture sizes (1/4, 1/9, 1/16 or 1/36 of normal size) with 8-bit resolution
• 15 predefined PIP display configurations and expert mode (fully programmable)
• control interface for external field memory
• I2C-bus interface
• one 20.25-MHz crystal, few external components
• 80-pin PQFP package
Pin Connections and Short Descriptions
NC = not connected
LV = if not used, leave vacant
X = obligatory; connect as described in circuit diagram
SUPPLY A = 4.75...5.25 V, SUPPLYD = 3.15...3.45 V
General description
The SDA55XX is a single chip teletext decoder for decoding World System Teletext data as well as Video Programming System (VPS), Program Delivery Control (PDC), and Wide Screen Signalling (WSS) data used for PAL plus transmissions (Line 23). The device also supports Closed caption acquisition and decoding. The device provides an integrated general-purpose, fully 8051-compatible Microcontroller with television specific hardware features. Microcontroller has been enhanced to provide powerful features such as memory banking, data pointers, and additional interrupts etc. The on-chip display unit for displaying Level 1.5 teletext data can also be used for customer defined on screen displays. Internal XRAM consists of up to16 Kbytes. Device has an internal ROM of up to 128 KBytes. ROMless versions can access up to 1 MByte of external RAM and ROM. The SDA 55XX supports a wide range of standards including PAL, NTSC and contains a digital slicer for VPS, WSS, PDC, TTX and Closed Caption, an accelerating acquisition hardware module, a display generator for Level 1.5 TTX data and powerful On screen Display capabilities based on parallel attributes, and Pixel oriented characters (DRCS).  The 8-bit Microcontroller runs at 360 ns. cycle time (min.). Controller with dedicated hardware does most of the internal TTX acquisition processing, transfers data to/from external memory interface and receives/transmits data via I2C-firmware user-interface. The slicer combined with dedicated hardware stores TTX data in a VBI buffer of 1 Kilobyte. The Microcontroller firmware performs all the acquisition tasks (hamming and parity-checks, page search and evaluation of header control bits) once per field. Additionally, the firmware can provide high-end Teletext features like Packet-26-handling, FLOF, TOP and list-pages. The interface to user software is optimized for minimal overhead. SDA 55XX is realized in 0.25 micron technology with 2.5 V supply voltage and 3.3 V I/O (TTL compatible). The software and hardware
development environment (TEAM) is available to simplify and speed up the development of the software and On Screen Display. TEAM stands for TVT Expert Application Maker. It improves the TV controller software quality in following aspects:
– Shorter time to market
– Re-usability
– Target independent development
– Verification and validation before targeting
– General test concept
– Graphical interface design requiring minimum programming and controller know how.
– Modular and open tool chain, configurable by customer
General Description
The TDA1308 is an integrated class AB stereo headphone driver contained in an SO8 or a DIP8 plastic package. The device is fabricated in a 1 mm CMOS process and has been primarily developed for portable digital audio applications.
Features
• Wide temperature range
• No switch ON/OFF clicks
• Excellent power supply ripple rejection
• Low power consumption
• Short-circuit resistant
• High performance
• high signal-to-noise ratio
• High slew rate
• Low distortion
• Large output voltage swing.
General description
The Genesis Microchip 6015RD1 LCD TV reference board is a complete display processor for LCD, PDP and LCOS based televisions. The reference board demonstrates the processing capabilities of the Genesis Microchip gm6015 television controller IC. The gm6015 IC is a full-featured, dual-channel video processor with Genesis industry leading Crystal Ciema PlusTM video scan conversion. The 6015RD1 board inputs analog YPbPr/RGB, NTSC/PAL/SECAM CVBS/YC, UHF/VHF and outputs digital RGB to an XGA LCD panel. A convenient on-screen display system provides easy control of the board’s processing capabilities.
The design kit is complete with hardware and software. Software includes G-Probe debug software, GWizard register calculator and G-TV application source code.
The 6015RD1 is a related reference board that outputs analog YpbPr/RGB.
Features
• Dual channel, gm6015 based LCD TV system
• Industry leading Crystal Cinema Plus video scan conversion
• Inputs:
i. Component analog YPbPr/RGB
ii. 480/576I, 480/576P, 720P and 1080I HD
iii. Dual NTSC/PAL/SECAM CVBS and YC
iv. VGA, SVGA, XGA PC graphics
v. Separate, composite or sync on Y/G
vi. UHF/VHF RF (NTSC)
• Default output with XGA LCD interface PCB:
i. Component analog YpbPr/RGB
• Other outputs:
ii. 8/16/20/24-bit 4:2:2/4:4:4 digital YCbCr/RGB
iii. 480/576I, 480/576P, 720P and 1080I HD
iv. VGA, SVGA, XGA PC graphics
v. Separate, composite or sync on Y/G
• On-screen display (OSD) user interface with automated self running demonstration
• Small form factor PCB
General Description
The MST9883C is a fully integrated analog interface for digitizing high-resolution RGB graphics signals from PC’s and workstations. With a sampling rate capability of up to 140 MHz, it can accurately support display resolutions up to 1280x1024 (SXGA) at 75 Hz. The clamped input circuits provide sufficient bandwidth to accurately digitize each pixel.
• Triple ADC with 12 - 140 MHz Sampling Rate
• Integrated line locked PLL generates pixel clock from HSYNC
• Integrated clamp with timing generator
• Integrated Brightness & Contrast controls
• Pin Compatible with AD9883A
• 4:2:2 and 4:4:4 Output Format Mode
• BT656 output format mode*
• Black and mid-level precision clamp and calibration
General description
The M74HC4052 is a dual four-channel analog MULTIPLEXER/DEMULTIPLEXER fabricated with silicon gate C2MOS technology and it is pinto pin compatible with the equivalent metal gate CMOS4000B series. It contains 8 bidirectional and digitally controlled analog switches.  A built-in level shifting is included to allow an input range up to 6V (peak) for an analog signal with digital control signal of 0 to 6V.
VEE supply pin is provided for analog input signals. It has an inhibit (INH) input terminal to disable all the switches when high. For operation as a digital multiplexer/demultiplexer, VEE is connected to GND.  A and B control inputs select one channel out of four in each section.
All inputs are equipped with protection circuits against static discharge and transient excess voltage.
Features
• Operation from 3.0 V to 40 V Input
• Low Standby Current
• Current Limiting
• Output Switch Current to 1.5 A
• Output Voltage Adjustable
• Frequency Operation to 100 kHz
• Precision 2% Reference
MSP34X0G
MSP3400G
Multistandard Sound Processor Family
Introduction
The MSP 34x0G family of single-chip Multistandard Sound Processors covers the sound processing of all analog TV-Standards worldwide, as well as the NICAM digital sound standards. The full TV sound processing, starting with analog sound IF signal-in, down to processed analog AF-out, is performed on a single chip. Figure shows a simplified functional block diagram of the MSP 34x0G.
This new generation of TV sound processing ICs now includes versions for processing the multichannel television sound (MTS) signal conforming to the standard recommended by the Broadcast Television Systems Committee (BTSC). The DBX noise reduction, or alternatively, MICRONAS Noise Reduction (MNR) is performed alignment free. Other processed standards are the Japanese FM-FM multiplex standard (EIA-J) and the FM Stereo Radio standard. Current ICs have to perform adjustment procedures in order to achieve good stereo separation for BTSC and EIA-J. The MSP 34x0G has optimum stereo performance without any adjustments.
All MSP 34x0G versions are pin and software downward compatible to the MSP 34x0D. The MSP 34x0G further simplifies controlling software. Standard selection requires a single I²C transmission only.
The MSP 34x0G has built-in automatic functions: The IC is able to detect the actual sound standard automatically (Automatic Standard Detection). Furthermore, pilot levels and identification signals can be evaluated internally with subsequent switching between mono/stereo/bilingual; no I²C interaction is necessary (Automatic Sound Selection)
I2S bus interface consists of five pins:
1. I2S_DA_IN1, I2S_DA_IN2: For input, four channels (two channels per line, 2*16 bits) per sampling cycle
(32 kHz) are transmitted.
2. I2S_DA_OUT: For output, two channels (2*16 bits) per sampling cycle (32 kHz) are transmitted.
3. I2S_CL: Gives the timing for the transmission of I2S serial data (1.024 MHz).
4. I2S_WS: The I2S_WS word strobe line defines the left and right sample.
Features
• Standard Selection with single I2C transmission
• Automatic Standard Detection of terrestrial TV standards
• Automatic Sound Selection (mono/stereo/bilingual), new registers MODUS, STATUS
• Two selectable sound IF (SIF) inputs
• Automatic Carrier Mute function
• Interrupt output programmable (indicating status change)
• Loudspeaker / Headphone channel with volume, balance, bass, treble, loudness
• AVC: Automatic Volume Correction
• Subwoofer output with programmable low-pass and complementary high-pass filter
• Spatial effect for loudspeaker channel
• Four Stereo SCART (line) inputs, one Mono input; two Stereo SCART outputs
• Complete SCART in/out switching matrix
• Two I2S inputs; one I2S output
• Dolby Pro Logic with DPL 351xA coprocessor
• All analog FM-Stereo A2 and satellite standards; AM-SECAM L standard
• Simultaneous demodulation of (very) high-deviation FM-Mono and NICAM
• Adaptive deemphasis for satellite (Wegener-Panda, acc. to ASTRA specification)
• ASTRA Digital Radio (ADR) together with DRP 3510A
• All NICAM standards
• Korean FM-Stereo A2 standard.
DS90C385
General Description
The DS90C385 transmitter converts 28 bits of LVCMOS/LVTTL data into four LVDS (Low Voltage Differential Signaling) data streams. A phase-locked transmit clock is transmitted in parallel with the data streams over a fifth LVDS link. Every cycle of the transmit clock 28 bits of input data are sampled and transmitted. At a transmit clock frequency of 85 MHz, 24 bits of RGB data and 3 bits of LCD timing and control data (FPLINE, FPFRAME, DRDY) are transmitted at a rate of 595 Mbps per LVDS data channel.  Using a 85 MHz clock, the data throughput is 297.5 Mbytes/sec. Also available is the DS90C365 that converts 21 bits of LVCMOS/LVTTL data into three LVDS (Low Voltage Differential Signaling) data streams. Both transmitters can be programmed for Rising edge strobe or Falling edge strobe through a dedicated pin. A Rising edge or Falling edge strobe transmitter will interoperate with a Falling edge strobe Receiver (DS90CF386/DS90CF366) without any translation logic.
The DS90C385 is also offered in a 64 ball, 0.8mm fine pitch ball grid array (FBGA) package which provides a 44% reduction in PCB footprint compared to the TSSOP package. This chipset is an ideal means to solve EMI and cable size problems associated with wide, high-speed TTL interfaces.
• 20 to 85 MHz shift clock support
• Best–in–Class Set & Hold Times on TxINPUTs
• Tx power consumption <130 mW (typ) @85MHz Grayscale
• Tx Power-down mode <200µW (max)
• Supports VGA, SVGA, XGA and Single/Dual Pixel SXGA
• Narrow bus reduces cable size and cost
• Up to 2.38 Gbps throughput
• Up to 297.5 Megabytes/sec bandwidth
• 345 mV (typ) swing LVDS devices for low EMI
• PLL requires no external components
• Compatible with TIA/EIA-644 LVDS standard
• Low profile 56-lead or 48-lead TSSOP package
• DS90C385 also available in a 64 ball, 0.8mm fine pitch ball grid array (FBGA) package
NDS8947
General Description
These P-Channel enhancement mode power field effect transistors are produced using Fairchild's proprietary, high cell density, DMOS technology. This very high density process is especially tailored to minimize on-state resistance and provide superior switching performance. These devices are particularly suited for low voltage applications such as notebook computer power management and other battery powered circuits where fast switching, low in-line power loss, and resistance to transients are needed.
Features
• -4A, -30V. RDS(ON) = 0.065W @ VGS = -10V
RDS(ON) = 0.1W @ VGS = -4.5V.
• High density cell design for extremely low RDS(ON).
• High power and current handling capability in a widely used surface mount package.
• Dual MOSFET in surface mount package.

Microcontroller Features
• 8bit 8051 instruction set compatible CPU.
• 33.33-MHz internal clock (max.)
• 0.360 ms (min.) instruction cycle
• Two 16-bit timers
• Watchdog timer
• Capture compare timer for infrared remote control decoding
• Pulse width modulation unit (2 channels 14 bit, 6 channels 8 bit)
• ADC (4 channels, 8 bit)
• UART (rxd, txd)
Memory
• Up to 128 Kilobyte on Chip Program ROM
• Eight 16-bit data pointer registers (DPTR)
• 256-bytes on-chip Processor Internal RAM (IRAM)
• 128bytes extended stack memory.
• Display RAM and TXT/VPS/PDC/WSS-Acquisition-Buffer directly accessible via MOVX
• UP to 16KByte on Chip Extended RAM (XRAM) consisting of;
- 1 Kilobyte on-chip ACQ-buffer-RAM (access via MOVX)
- 1 Kilobyte on-chip extended-RAM (XRAM, access via MOVX) for user software
- 3-Kilobyte Display Memory
Display Features
• ROM Character set supports all East and West European Languages in single device
• Mosaic Graphic Character Set
• Parallel Display Attributes
• Single/Double Width/Height of Characters
• Variable Flash Rate
• Programmable Screen Size (25 Rows x 33...64 Columns)
• Flexible Character Matrixes (HxV) 12 x 9...16
• Up to 256 Dynamical Redefinable Characters in standard mode; 1024 Dynamical Redefinable Characters
in Enhanced Mode
• CLUT with up to 4096 colour combinations
• Up to 16 Colours per DRCS Character
• One out of 8 Colours for Foreground and Background Colours for 1-bit DRCS and ROM Characters.
ROM Characters
• Shadowing
• Contrast Reduction
• Pixel by Pixel Shiftable Cursor With up to 4 Different Colours
• Support of Progressive Scan and 100 Hz.
• 3 X 4Bits RGB-DACs On-Chip
• Free Programmable Pixel Clock from 10 MHz to 32MHz
• Pixel Clock Independent from CPU Clock
• Multinorm H/V-Display Synchronisation in Master or Slave Mode
Acquisition Features
• Multistandard Digital Data Slicer
• Parallel Multi-norm Slicing (TTX, VPS, WSS, CC, G+)
• Four Different Framing Codes Available
• Data Caption only limited by available Memory
• Programmable VBI-buffer
• Full Channel Data Slicing Supported
• Fully Digital Signal Processing
• Noise Measurement and Controlled Noise Compensation
• Attenuation Measurement and Compensation
• Group Delay Measurement and Compensation
• Exact Decoding of Echo Disturbed Signals
Features
Features
Features
SDA55XX (SDA5550)
TPA3002D2
General Description
The TPA3002D2 is a 9-W (per channel) efficient, Class-D audio amplifier for driving bridged-tied stereo speakers. The TPA3002D2 can drive stereo speakers as low as 8 Ω. The high efficiency of the TPA3002D2 eliminates the need for external heatsinks when playing music.
Features
• 9-W/Ch Into an 8-Ω Load From 12-V Supply
• Efficient, Class-D Operation Eliminates Heatsinks and Reduces Power Supply Requirements
• 32-Step DC Volume Control From -40 dB to 36 dB
• Line Outputs For External Headphone Amplifier With Volume Control
• Regulated 5-V Supply Output for Powering TPA6110A2
• Space-Saving, Thermally-Enhanced PowerPADTM Packaging
• Thermal and Short-Circuit Protection.
TDA9885/86
General description
The TDA9885 is an alignment-free single standard (without positive modulation) vision and sound IF signal PLL.
The TDA9886 is an alignment-free multistandard (PAL, SECAM and NTSC) vision and sound IF signal PLL demodulator for positive and negative modulation including sound AM and FM processing. Both devices can be used for TV, VTR, PC and set-top box applications.
Features
• 5 V supply voltage
• Gain controlled wide-band Vision Intermediate Frequency (VIF) amplifier (AC-coupled)
• Multistandard true synchronous demodulation with active carrier regeneration (very linear demodulation, good intermodulation figures, reduced harmonics, excellent pulse response)
• Gated phase detector for L/L accent standard
• Fully integrated VIF Voltage Controlled Oscillator (VCO), alignment-free; frequencies switchable for all negative and positive modulated standards via I2C-bus
• Digital acquisition help, VIF frequencies of 33.4, 33.9, 38.0, 38.9, 45.75 and 58.75 MHz
• 4 MHz reference frequency input [signal from Phase-Locked Loop (PLL) tuning system] or operating as crystal oscillator
• VIF Automatic Gain Control (AGC) detector for gain control, operating as peak sync detector for negative modulated signals and as a peak white detector for positive modulated signals
• Precise fully digital Automatic Frequency Control (AFC) detector with 4-bit digital-to-analog converter; AFC bits via I2C -bus readable
• TakeOver Point (TOP) adjustable via I2C-bus or alternatively with potentiometer
• Fully integrated sound carrier trap for 4.5, 5.5, 6.0 and 6.5 MHz, controlled by FM-PLL oscillator
• Sound IF (SIF) input for single reference Quasi Split Sound (QSS) mode (PLL controlled)
• SIF AGC for gain controlled SIF amplifier; single reference QSS mixer able to operate in high performance single reference QSS mode and in intercarrier mode, switchable via I2C-bus
• AM demodulator without extra reference circuit
• Alignment-free selective FM-PLL demodulator with high linearity and low noise
• I2C-bus control for all functions
• I2C-bus transceiver with pin programmable Module Address (MAD).
TDA1308
PI5V330
General description
Pericom Semiconductor’s PI5V series of mixed signal video circuits are produced in the Company’s advanced CMOS low-power technology, achieving industry leading performance.  The PI5V330 is a true bidirectional Quad 2-channel multiplexer/demultiplexer that is recommended for both
RGB and composite video switching applications. The VideoSwitch™ can be driven from a current output RAMDAC or voltage output composite video source.
Low ON-resistance and wide bandwidth make it ideal for video and other applications. Also this device has exceptionally high current capability which is far greater than most analog switches offered today. A single 5V supply is all that is required for operation.  The PI5V330 offers a high-performance, low-cost solution to switch between video sources. The application section describes the PI5V330 replacing the HC4053 multiplier and buffer/amplifier.
Features
• High-performance, low-cost solution to switch between video sources
• Wide bandwidth: 200 MHz
• Low ON-resistance: 3W
• Low crosstalk at 10 MHz: –58 dB
• Ultra-low quiescent power (0.1 µA typical)
• Single supply operation: +5.0V
• Fast switching: 10 ns
• High-current output: 100 mA
• Packages available:
– 16-pin 300-mil wide plastic SOIC (S)
– 16-pin 150-mil wide plastic SOIC (W)
– 16-pin 150-mil wide plastic QSOP (Q)
GM6015
MST9883
M74HC4052
features
• low power dissipation:
icc = 4µa (max.) at ta=25°c.
• logic level translation to enable 5v logic signal to communicate with ±5v
analog signal
• low "on" resistance:
70Ω typ. (vcc - vee = 4.5v)
50Ω typ. (vcc - vee = 9v)
• wide analog input voltage range: ±6v
• fast switching: tpd = 15ns (typ.) at ta = 25 °c
• low crosstalk between switches
• high on/off output voltage ratio
• wide operating supply voltage range (vcc - vee) = 2v to 12v
• low sine wave distortion: 0.02% at vcc - vee = 9v
• high noise immunity: vnih = vnil = 28 % vcc (min.)
MC34063
Description
The MC34063A Series is a monolithic control circuit containing the primary functions required for DC–to–DC converters. These devices consist of an internal temperature compensated reference, comparator, controlled duty cycle oscillator with an active current limit circuit, driver and high current output switch. This series was specifically designed to be incorporated in Step–Down and Step–Up and Voltage–Inverting applications with a minimum number of external components.
Source Select
• 5-band graphic equalizer for loudspeaker channel