How to enter Service Mode _ Initialization _ Firmware Upgrade _ White Balance adjustment _ PHILIPS 32PFL3506/F7
- 32PFL3000/F8 _ LCD TV
SERVICE MODE
* Turn
the power on.
* Press [MENU] button to display Setup menu.
* Select “Features”.
* Select “Current Software Info”.
* Press [0], [6], [2], [5], [9], [6] and [INFO] buttons on the remote control unit in this order. The following screen appears.
* Press [MENU] button to display Setup menu.
* Select “Features”.
* Select “Current Software Info”.
* Press [0], [6], [2], [5], [9], [6] and [INFO] buttons on the remote control unit in this order. The following screen appears.
Purity
Check
This mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels.
* Enter the Service mode.
* Each time the [7] button on the remote control unit is pressed, the display changes as follows.
This mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels.
* Enter the Service mode.
* Each time the [7] button on the remote control unit is pressed, the display changes as follows.
* To
cancel or to exit from the Purity Check Mode, press [PREV CH] button.
VCOM
Adjustment
Set
the color analyzer at the zero point calibration and bring the optical receptor
pointing at the center of the LCD-Panel at a distance of 1.18 inches(3cm) away
from the LCD-Panel surface.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
* Enter the Service mode.
* Press [2] button on the remote control unit.
* Press [CH + or -] buttons on the remote control unit so that the color analyzer value becomes minimum within 2 minutes from Power-On.* To cancel or to exit from the VCOM Adjustment, press [PREV CH] button.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
* Enter the Service mode.
* Press [2] button on the remote control unit.
* Press [CH + or -] buttons on the remote control unit so that the color analyzer value becomes minimum within 2 minutes from Power-On.* To cancel or to exit from the VCOM Adjustment, press [PREV CH] button.
The
White Balance Adjustment should be performed when replacing the LCD Panel or
Digital Main CBA
Symptom
of Maladjustment: White becomes bluish or reddish.
Operate
the unit for more than 60 minutes.
Input the White Raster(70%=70IRE, 40%=40IRE).
> Set
the color analyzer at the CHROMA mode and zero point calibration. Bring the optical
receptor pointing at the center of the LCD-Panel at a distance of 1.18 inches (3cm)
away from the LCD Panel surface.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
Enter the Service mode. Press [VOL -] button on the remote control unit and select “C/D” mode.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
Enter the Service mode. Press [VOL -] button on the remote control unit and select “C/D” mode.
CUTOFF
> Press [1] button to select “COR” for Red Cutoff adjustment. Press [3] button to select “COB” for Blue Cutoff adjustment.
DRIVE
> Press [4] button to select “DR” for Red Drive adjustment. Press [6] button to select “DB” for Blue Drive adjustment. In each color mode, press [CH + or -] buttons to adjust the values of color.
> Adjust Cutoff and Drive so that the color temperature becomes 12000°K (x= 0.272 / y= 0.278 ± 0.005).
To cancel or to exit from the White Balance Adjustment, press [PREV CH] button.
> Press [1] button to select “COR” for Red Cutoff adjustment. Press [3] button to select “COB” for Blue Cutoff adjustment.
DRIVE
> Press [4] button to select “DR” for Red Drive adjustment. Press [6] button to select “DB” for Blue Drive adjustment. In each color mode, press [CH + or -] buttons to adjust the values of color.
> Adjust Cutoff and Drive so that the color temperature becomes 12000°K (x= 0.272 / y= 0.278 ± 0.005).
To cancel or to exit from the White Balance Adjustment, press [PREV CH] button.
HOW
TO INITIALIZE THE LCD TV
The purpose of initialization
is to place the set in a new out of box condition. The customer will be
prompted to select a language and program channels after the set has been initialized. To put the program back at the
factory-default, initialize the LCD TV using the following procedure.
32PFL3506/F7
- 32PFL3000/F8 - (Serial No.: DS1, XA1)
- (Serial No.: XA1)
* Turn the power on.
* Enter the service mode. To cancel the service mode, press [Power] button on the remote control unit.
* Press [INFO] button on the remote control unit to initialize the LCD television. "INITIALIZED" will appear in the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is completed.
* Enter the service mode. To cancel the service mode, press [Power] button on the remote control unit.
* Press [INFO] button on the remote control unit to initialize the LCD television. "INITIALIZED" will appear in the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is completed.
32PFL3506/F7
- 32PFL3000/F8 (Serial No: DS2, DS3) - (Serial No: XA2)
* Turn the power on.
* Enter the service mode. To cancel the service mode, press [Power] button on the remote control unit.
* Press [FREEZE] button on the remote control unit to initialize the LCD television.
"INITIALIZED" will appear in the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is completed.
* Enter the service mode. To cancel the service mode, press [Power] button on the remote control unit.
* Press [FREEZE] button on the remote control unit to initialize the LCD television.
"INITIALIZED" will appear in the upper right of the screen. "INITIALIZED" color will change to green from red when initializing is completed.
Firmware
Update Procedure
Note: There are two states (the User Upgrade and the Factory Upgrade) in firmware update.
Note: There are two states (the User Upgrade and the Factory Upgrade) in firmware update.
User Upgrade > Upgrade the
firmware only. The setting values are
not initialized.
Factory upgrade > Upgrade
the firmware and initialize the setting values.
Factory Upgrade (Flash
upgrade) > Upgrade the firmware and initialize the setting values along with
the setting data adjusted at the factory such as White Balance, etc.
32PFL3506/F7
(Serial No.: DS2, DS3) _ 32PFL3000/F8 (Serial No.: XA2)
The identification of User
Upgrade and Factory Upgrade are done by the filename.
* Turn the power off and unplug the AC Cord.
* Insert the USB storage device to the USB port as shown here.
* Turn the power off and unplug the AC Cord.
* Insert the USB storage device to the USB port as shown here.
* The update will start and the
following will appear on the screen.
* When the firmware update is
completed, the following will appear on the screen.
* Remove the USB storage device
from the USB port.
* Turn the power off and turn the power on again.
* Turn the power off and turn the power on again.
When the Factory Upgrade is
used, after restarting TV, shift to initial screen menu in service mode.
"INITIALIZED" will appear on the upper right of the screen.
"INITIALIZED" color will change to green from red when initializing is completed.