Service Mode entry Procedures & Adjustment Details _ PANASONIC CT-20SX11E _ CT-20SX11CE – Color TV.
Universal Remote control Set-up codes to check with Panasonic Brand TVs (For CRT, LCD & Plasma type TVs)
0016 0032 0033 0049 0054 0075
0099 0101 0104 0107 0110 0119 0143 0151 0152 0161 0166 0207 0249 0304 0305 0306
0396 0420 0461 0611 0631 0633 0692
There are two ways to enter the service mode to these model TVs. Using the supplied remote control, and by opening the back cover of the set, and by shorting the TPs [Test Points]; described here.
USING THE REMOTE CONTROL
> Select
SET-UP icon and select CABLE mode.
> Select TIMER icon and set SLEEP time for 30 Min.
> Press ACTION button twice to exit menus.
> Tune to the Channel 124.
> Adjust VOLUME to minimum (0).
> Press the VOL button ◄ (decrease) on
Receiver. Red “CHK” appears in upper corner.> Select TIMER icon and set SLEEP time for 30 Min.
> Press ACTION button twice to exit menus.
> Tune to the Channel 124.
> Adjust VOLUME to minimum (0).
To toggle between Aging and Service modes:
* While the “CHK” is displayed on the left top corner of the CRT, pressing the Action and the Volume Up buttons on the Receiver simultaneously will toggle between the modes. Red “CHK” for Service and yellow “CHK” for Aging.
* While the “CHK” is displayed on the left top corner of the CRT, pressing the Action and the Volume Up buttons on the Receiver simultaneously will toggle between the modes. Red “CHK” for Service and yellow “CHK” for Aging.
Entering Service Mode (Back-Open Method)
>> While the Receiver is ON and operating in Normal Mode, momentarily short test point FA1 (TP8) to Cold Ground ( ) FA2 (TP3) A-Board. (The Receiver enters the Aging Mode.)
Yellow letters “CHK” appear in the upper left corner of the CRT. (The Volume Up/Down will adjust rapidly).
>> Simultaneously press the Action and the Volume Up buttons on the Receiver Control Panel.
The Receiver enters the Service Mode.
>> The letter in “CHK” turns red. (The Volume Up/Down will adjust normally). (All customer controls are set to nominal level)
>> While the Receiver is ON and operating in Normal Mode, momentarily short test point FA1 (TP8) to Cold Ground ( ) FA2 (TP3) A-Board. (The Receiver enters the Aging Mode.)
Yellow letters “CHK” appear in the upper left corner of the CRT. (The Volume Up/Down will adjust rapidly).
>> Simultaneously press the Action and the Volume Up buttons on the Receiver Control Panel.
The Receiver enters the Service Mode.
>> The letter in “CHK” turns red. (The Volume Up/Down will adjust normally). (All customer controls are set to nominal level)
Press the Power Button on the Remote Control to select one of six
Service Adjustment Modes.
B= Service VCJ SUB-DATA ADJUSTEMENT.
C= Service VCJ CUT-OFF ADJUSTMENT.
S= Service OPTIONS (PIP and CLOCK) ADJUSTMENT.
M= Service MTS ADJUSTMENTS.
X = Service COMB FILTER ADJUSTMENT.
“CHK” = Normal operation of CHANNEL▲▼ and VOLUME◄►.
B= Service VCJ SUB-DATA ADJUSTEMENT.
C= Service VCJ CUT-OFF ADJUSTMENT.
S= Service OPTIONS (PIP and CLOCK) ADJUSTMENT.
M= Service MTS ADJUSTMENTS.
X = Service COMB FILTER ADJUSTMENT.
“CHK” = Normal operation of CHANNEL▲▼ and VOLUME◄►.
Exiting the Service Mode:
* Press the Action and the Power buttons on the Receiver simultaneously for at least 2 seconds.
THE RECEIVER EXITS SERVICE MODE.
{The Receiver momentarily shuts off; then comes back on tuned to channel 3 with a preset level of sound. Any programmed channels, channels caption data and some others user defined settings will be erased.}
* Press the Action and the Power buttons on the Receiver simultaneously for at least 2 seconds.
THE RECEIVER EXITS SERVICE MODE.
{The Receiver momentarily shuts off; then comes back on tuned to channel 3 with a preset level of sound. Any programmed channels, channels caption data and some others user defined settings will be erased.}
Service Mode Menu Adjustments.
An
address Menu appears in the right hand corner of the screen.
IMPORTANT:
Always Exit the Service Mode Following Adjustments.
* Press the Power Button on the Remote Control to select the Service
Adjustment
For Adjustments
* Press Channel Up/Down on the Remote Control to
select one of the available Service Adjustments. [Write Down the original value
set for each address before modifying anything. It is easy to erroneously
adjust the wrong item]
* Press Volume Up/Down on
the Remote Control to adjust the
level of the selected Service Adjustment.
To Check Purity
Press the Recall Button on the Remote Control when in Service Mode (red “CHK” is displayed) to enter the Purity Field Check Mode.
Press the Recall Button on the Remote Control when in Service Mode (red “CHK” is displayed) to enter the Purity Field Check Mode.
CLICK ON THE PICTURES TO ZOOM IN
See the next post here to see the Schematic [Circuit diagram] to these models Panasonic CTVs
