Saturday, October 22, 2016

LG Arena sports LCD TV – How to disassemble the LCD screen - 42 inch LCD TV

Lamp
It is a light source that emits a visible beam with a high power inverter. Utilizase CCFL (Cold Cathode Fluorescent Lamp).
LGP Light guide Panel (Panel guide light)
Is produced in the method Injection Mold, acrylic (PMMA). Reflects the light source receive. dissipate the light source homogeneously.
Lamina Reflector
It is a guide panel made of PET, has function to reflect the light to reduce the loss of source received light to guide panel.
Diffuser Down (Layer Diffusor)
It is made mainly PET and acrylic resin. Diffuses the light source homogeneously and it also has function of concentration of light.
Prism Lower
It is made mainly PET and acrylic resin. regularly form an image prism, thereby concentrating the light.
Increases the brightness by 1:55 times greater than the surface Diffusers.
Prisma Higher
Has Same function with Lower Prisma and increases by 1:33 times the brightness in compared to the surface of Superior Prism.
The Prisms must be crossed, in order to focus the lights of the X and Y axes, respectively.
Diffuser Up (protective film)
has Same structure with Diffuser Down and its main purpose is to protect the prism, by this is called as Protector Film.
Uses mainly diffusers' with high filterability. This brings some loss of light concentrated by Prisma Superior, but is used to minimize failure due to characteristic of the prism.
Tools needed
Use of Jig and always necessary to facilitate technician to identify defect, and confirms what should be really changed.
The use of suction cup is extremely necessary, when we work with over 42 screens Inches.
It is easier to remove and reduces possibility of breaking the screen.
Protection of access to the flats (B.A)
For LC420DUE.ABGA4 module model. should follow the following steps
Remove the following screws, as shown below
Removing protective plate T-Con.
First step is to remove the metal protection TCON board. as the screens follow.
Loosen the screws
Remove the T-Con. with flats
Remember the screws are different from the others and not They can be placed in another local.
We should always be careful when removing the flat.
Never remove with flat with the connected device.
When fitting, make sure that its terminals are not jammed.
Centralize and the flat before locking it.
Remove the top frieze (Frame)
To remove the upper Friso (frame), the module LC420DUE.ABGA4
We must loosen the following screws, as shown below.
See that there is 11 screws on the side and top (superb thread screws).
In the bottom of only 3 screws (fine thread)
Loosen all screws and remove the frame.
Withdrawal of the side rails (frame-less modules)
Some modules have to remove the and also the frame side rails.
As an example the figure shown.
Board Assy (B.A)
After removing the upper frieze LC420DUE.ABGA4 module
Unhook the side plates of the Board Assy (BA)
With the help of Ventosa, set in (B.A) erga removing carefully.
Now let's take the support grill (B.A)
For this we will use a spatula to unlock the grid fits with care that it is not damaged.
Support grid withdrawal of (B.A)
Withdrawal of Prisms
In the figure below shows the layout of the diffuser filters.
It is advisable to keep them together so that no dirt residues between them.
Always wear gloves so that it do not get fat brands or other products.
Remove the diffuser filters.
Remember to keep together.
Do not allow them to become exposed to sunlight directly
Do not get water residue or other products.
Support towers withdrawal
After removing all the light, remove the support towers.
These towers are responsible for fixing the reflector plate and support the diffuser plates.
To release them unlock the bottom of the panel.
The towers may have various shapes and forms
Always take care not to pull the reflective hold the towers.
There are several types of pain.
Below are some examples of how base.
Note .: The item comes with adhesive on the cards for fixing the Cover Bottom (Tape does not exist in BOM)
Withdrawal of Reflector
After removing all the light, the reflective strip
Take care to verify that it is not taped at the bottom.
If the same has the adhesive must be very careful to remove the reflector.
Do not lift the reflector suddenly, it may be arrested with tape.
Ressolda between bone connector will conclude the work.
League panel but goes off the backlight.
Bad contact in connector Leds bar.
Pegue a wire to be placed between the terminals, may be a source wire cables, as shown below.
Soldar the thread already cut as shown in Figure
Após have welded the jumper, connect the unit and make sure everything is lit as expected.