Philips Blu-ray Disc Player BDP3380 – smps board circuit diagram – how to upgrade the software

Power
• Power supply: 220-230V, 50Hz
• Power consumption: 18 W
• Standby power consumption: 0.3W
Video Playback
• Playback Media: BD Video, BD-ROM, BD-R/RE 2.0, DVD, DVD-Video, DVD+R/+RW, DVD-R/-RW, Video CD/SVCD, CD, CD-R/CD-RW, USB flash drive, DivX
• Compression formats: DivX Plus™ HD, MKV, H.264, MPEG2, VC-1, WMV, XviD, AVCHD
• Disc Playback Modes: Standard Play, Pause, Search forward/reverse, Slow Forward, Resume Playback from Stop, Skip, Disc Menu, Repeat, A-B Repeat, Zoom, Angle
• Video Enhancement: Deep Color, x.v. Color, Video Upscaling, Progressive Scan
• BD Region Code: B
• DVD Region Code: 2

Picture/Display
• Aspect ratio: 21:9, 16:9, 4:3
• Picture enhancement: High Def (720p, 1080i, 1080p), Progressive scan, Video upscaling
• D/A converter: 12Bit/148MHz.

Software check and upgrade

Preparation to upgrade software
1) Start the CD burning software & create a folder named "UPG_ALL", B. Read out the software versions to confirm upgrading
2) Then copy the Bin file (BDP3380.bin )into it,
3) Burn the data onto the blank CD or USB. 1) Power on the set and open the tray door.
4) If the model is BDP3300,must use (BDP3300.bin )to upgrade 2) Press <Home> button on the remote control.
A. Procedure for software upgrade 3) Select <Setup>, then press <OK>.
A) Upgrade software via Disc 4) Select <Advanced>, press right cursor to choose
1) Power on the set and insert the prepared Upgrade <Version Information.>, then press <OK>, the software version
CDR. and other information will display on the TV screen as below:
2) The set will starts reading disc & response with the Model:BDP3XXX/XX
following display TV screen: Version:
Now searching for upgrade software! System SW: X.XX
Please wait…!

3) Press <OK> button to confirm, then screen will display : For information,frequently asked questions and software upgrades,
An upgrade software has been found! visit http://www.philips.com/support
Start upgrade with version:WKXXX.X?

4) Press Right cursor button to choose "Start", then press <OK>; damaged entirely.
5) The software will upgrade and screen will display as below:
Upgrade is ongoing, Please wait…
Please do not unplug or switch off the device.
6) The screen will display as below when upgrading complete:
Upgrade has completed successfully!
Power off after 5s.

5) Restart the set.

SMPS (Power board) schematic

B) Upgrade the software via network:

1) Setup the network connection (See "Getting started">"Set up network").

2) In the Home menu, select <Setup>-<Advanced>- <Software update>-<Network>.

* You are prompted to start upgrading processes if upgrade media is detected.

3) Follow the instructions on the TV screen to confirm update operation.

* Once software updated is complete, this player automatically turns off to standby.

4) Disconnect the power cord for a few seconds and connect again

to turn on the player.

C) Update software via USB Flash Drive:

1) Go to www.philips.com/support to check if the latest software

version is available for this player.

2) Download the software onto a USB flash drive.

3) Insert the USB flash drive to the USB jack of the rear panel.

4) In the Home menu, select <Setup>-<Advanced>-<Software Update >-<USB>.

5) Follow the instructions on the TV screen to confirm update operation.

* Once software update is complete, this player automatically turns to standby.

6) Disconnect the power cord for a few seconds and connect again to

turn on the player.

B. Read out the software versions to confirm upgrading

1) Power on the set and open the tray door.

2) Press <Home> button on the remote control.

3) Select <Setup>, then press <OK>.

4) Select <Advanced>, press right cursor to choose

<Version Information.>, then press <OK>, the software version and other information will display on the TV screen as below:

Model:BDP3XXX/XX

Version:

System SW: X.XX

Ethernet MAC:XX-XX-XX-XX-XX-XX

[The set must not be power off during upgrading, otherwise the Main board will be damaged entirely.]