PCB assembly adjustment items
1) Download the VCTP main software (IC500,VCT_Pro)
2) Channel memory (IC501,EEPROM)
3) Color carrier Adjustment
SET assembly adjustment items
1) DDC Data input.
2) Adjustment of White Balance.
3) Factoring Option Data input
1) Download the VCTP main software (IC500,VCT_Pro)
2) Channel memory (IC501,EEPROM)
3) Color carrier Adjustment
SET assembly adjustment items
1) DDC Data input.
2) Adjustment of White Balance.
3) Factoring Option Data input
PCB assembly adjustment method (Using
VCTP Download program)
Download program installation
(1) Extract a Zip file
(1) Extract a Zip file
(2) Visual I2C & LPT Driver
Installation
Install the LPT Driver
Install the Visual I2C
Click on the pictures to magnify
LPT Port Driver (LptDrv) Setups :
Program Files > Micronas > Visual I2C > Port_Driver
*Use for Windows 95/98 : Setup_LptDrv_v0104_9x.exe
*Use for Windows 2000/XP : Setup_LptDrv_v0202_XP_2000.exe
*Use for Windows NT : Setup_LptDrv_v0104_NT.exe
*Use for Windows 95/98 : Setup_LptDrv_v0104_9x.exe
*Use for Windows 2000/XP : Setup_LptDrv_v0202_XP_2000.exe
*Use for Windows NT : Setup_LptDrv_v0104_NT.exe
(3) Verification (Start > Programs
> Micronas >Visual I2C or LptDrv)
(4) LPT delay setting (File >
Preference > LPT preferences)
(5) Exchange the bootloader.bat file.
=> Select the
"Bootloader.bat" file(install > VCTP_download > Bootloader)
=> Push "OK"
=> Push "OK"
=> Finish the program, after saving
the file "download_cs.vi2c" (if
you click [X] , the massage appears automatically)
S/W program download
(1) Download method 1 (PCB Ass’y)
Connect the download jig to D-sub
jack.
2) Execute ‘Download.vi2c’ program in PC, then a main window will be opened.
2) Execute ‘Download.vi2c’ program in PC, then a main window will be opened.
3) Double click the blue box and
confirm "Bootloader Version"
4) Click the "Erase Flash"
button.
5) Double click the download file low,
then "edit" window will be opened.
6) Click the choice button in the
“edit window”, then “file choice window” will be opened.
7) Choose the Hex file in folder and
execute downloading with click " open" button.
8) Click OK button at the "edit window".
9) Under downloading process
10) If download is failed, for example "No acknowledge from slave". Execute download again from(1).
(2) Download method 2 (AV Plate Ass’y)
Push S/W ‘ON’(connect SCL to GND using
switch at Jig) and connect the download jig to D-sub jack.
2) Supply the power (Stand-by 5V) and
wait for 3 seconds.
3) Push the S/W off (Disconnect SCL to
GND using switch at jig).
4) Execute ‘Download.vi2c’ program in
PC, then a main widow will be opened.
5) Double click the blue box and
confirm "Bootloader Version"
6) Click the "Erase Flash" button.
7) Double click the download file low
then, "edit" window will be opened.
8) Chick the choice button I n the
"edit window", then "file choice window’ will be opened.
9) Choose the Hex file in folder and
execute downloading with click "open button"
10) Click OK button at the "edit
window"
11) Under downloading progress.
12) If download is failed, for example
"No acknowledge from slave", execute download again from (1).
(3) Download method 3 (SET)
1) Push the “Tilt” button in an Adjust Remote control Then the LCD TV will change a “slave mode”.
1) Push the “Tilt” button in an Adjust Remote control Then the LCD TV will change a “slave mode”.
2) Connect Zig to TV using a D-sub
cable.
3) Execute ‘Download_CS.vi2c’ program
in PC, then a main widow will be opened
4) Click "GO" button
[If you don’t push the “go”, the Hex
file would not be downloaded although the download proceeds normally at first
glance.]
5) Double click the blue box and
confirm "Bootloader Version"
6) Click the "Erase Flash"
button
7) Double click the download file low
then, "edit" window will be opened.
8) Chick the choice button I n the
"edit window", then "file choice window’ will be opened
9) Choose the Hex file in folder and
execute downloading with click "open button"
10) Click OK button at the "edit
window"
11) Downloading
12) If download is failed, for example
"No acknowledge from slave", execute download again from (1)
Chancel memory download
(1) Connect the download jig to D-sub jack.
(2) Execute ‘Channel.vi2c’ program in PC, then a main window will be opened
(1) Connect the download jig to D-sub jack.
(2) Execute ‘Channel.vi2c’ program in PC, then a main window will be opened
(3) Push the button change and select
the Channel memory data
(4) Check the communication is OK or
not.
=> Push the Read area (Ackn. Check) and check Cyan area is OK message.
=> Push the Read area (Ackn. Check) and check Cyan area is OK message.
(5) Push the Update NVM from File
Tool Option Area Option Change
Before PCBA check, have to change the Tool option and Area option
Option values are below
(If no changed the option, the input menu can differ the model spec.)
The input methods are same as other chastises (Use adj Key on the Adjust Remote control)
Before PCBA check, have to change the Tool option and Area option
Option values are below
(If no changed the option, the input menu can differ the model spec.)
The input methods are same as other chastises (Use adj Key on the Adjust Remote control)
EDID (The Extended Display Identification Data ) /DDC(Display Data Channel) download
Caution
- Use the proper signal cable for EDID Download.
- Never connect HDMI & D-SUB Cable at the same time.
- Use the proper cables below for EDID Writing.
Required Test Equipment
(1) Adjusting PC with S/W for writing EDID data.(S/W : EDID TESTER ver.2.5)
(2) A Jig for EDID Download.
(3) Cable : Serial(9Pin or USB) to D-sub 15Pin cable, D-sub 15Pin cable, DVI to HDMI cable.
(1) Adjusting PC with S/W for writing EDID data.(S/W : EDID TESTER ver.2.5)
(2) A Jig for EDID Download.
(3) Cable : Serial(9Pin or USB) to D-sub 15Pin cable, D-sub 15Pin cable, DVI to HDMI cable.
Preparation for Adjustment
(1) As above Fig 5, Connect the Set, EDID Download Jig, PC&Cable.
(2) Turn on the PC & EDID Download Jig. And execute the S/W : EDID TESTER Ver.2.5.
(3) Set up the S/W option.
Repeat Number : 5
Device Address : A0
PageByte : 8
(1) As above Fig 5, Connect the Set, EDID Download Jig, PC&Cable.
(2) Turn on the PC & EDID Download Jig. And execute the S/W : EDID TESTER Ver.2.5.
(3) Set up the S/W option.
Repeat Number : 5
Device Address : A0
PageByte : 8
(4) Power on the Set.
Sequence of Adjustment
(1) DDC data of Analog-RGB
1) Init the data
(1) DDC data of Analog-RGB
1) Init the data
2) Load the EDID data. (Open file)
[Analog - RGB : LP78B_RGB.ANA]
[Digital - HDMI1 : LP78B_HDMI1.DVI]
[Digital - HDMI2 : LP78B_HDMI2.DVI]
[Analog - RGB : LP78B_RGB.ANA]
[Digital - HDMI1 : LP78B_HDMI1.DVI]
[Digital - HDMI2 : LP78B_HDMI2.DVI]
3)Set the S/W as below
4) Push the “Write Data &
Verify”button. And confirm “Yes”.
5) If the writing is finished, you will see the “OK” message.
Adjustment of White Balance
Purpose and Principle
(1) Purpose: Adjust the color temperature to reduce the deviation of the module color temperature.
(2) Principle: To adjust the white balance without the saturation,Fix the one of R/G/B gain to 80 and decrease the others.
Adjustment mode
Two modes of Cool and Warm
(Medium data is automatically calibrated by the cool data)
Required Equipment
(1) Remote control for adjustment
(2) Color Analyzer (CA-110 or CA-210 or same product) - ch9
(3) Auto W/B adjustment instrument(only for Auto adjustment)
Connecting diagram of equipment for measuring (For Automatic Adjustment)
5) If the writing is finished, you will see the “OK” message.
Adjustment of White Balance
Purpose and Principle
(1) Purpose: Adjust the color temperature to reduce the deviation of the module color temperature.
(2) Principle: To adjust the white balance without the saturation,Fix the one of R/G/B gain to 80 and decrease the others.
Adjustment mode
Two modes of Cool and Warm
(Medium data is automatically calibrated by the cool data)
Required Equipment
(1) Remote control for adjustment
(2) Color Analyzer (CA-110 or CA-210 or same product) - ch9
(3) Auto W/B adjustment instrument(only for Auto adjustment)
Connecting diagram of equipment for measuring (For Automatic Adjustment)
Enter the adjustment mode of the white balance
Enter the white balance adjustment mode at the same time heat-run mode when pushing the power on by power only key.
Maintain the white balance adjustment mode with same condition of Heat-run. (Maintain after AC off/on in status of Heat-run pattern display)
(2) Release the white balance adjustment mode
Release the adjust mode after AC off/on or std-by off/on in status of finishing the Hear-run mode
Release the Adjust mode when receiving the aging off command(F3 00 00) from adjustment equipment
Need to transmit the aging off command to TV set after finishing the adjustment.
Standard color coordinate and temperature when using the CA-110 or CA210 equipment.
Enter the white balance adjustment mode at the same time heat-run mode when pushing the power on by power only key.
Maintain the white balance adjustment mode with same condition of Heat-run. (Maintain after AC off/on in status of Heat-run pattern display)
(2) Release the white balance adjustment mode
Release the adjust mode after AC off/on or std-by off/on in status of finishing the Hear-run mode
Release the Adjust mode when receiving the aging off command(F3 00 00) from adjustment equipment
Need to transmit the aging off command to TV set after finishing the adjustment.
Standard color coordinate and temperature when using the CA-110 or CA210 equipment.
R/G/B GAIN Max value > 80
Luminance Min value is 200cd/m2 in cool mode [for LCD]
Adjustment of White Balance
(For Manual adjustment)
Adjustment mode : Two modes of Cool (Dynamic) and Warm(Mild) (Medium data is automatically calibrated by the cool data)
Color analyzer(CA110, CA210) should be used in the calibrated ch by CS-1000.(LCD : CH9)
For manual adjustment, it is also possible by the following sequence
Operate the zero-calibration of the CA-110 or CA-210, then stick sensor to the module when adjusting.
(1) Select white pattern of heat-run by pressing “POWER ON” key on remote control for adjustment then operate heat run longer than 15 minutes. (If not executed this step, the condition for W/B will be differ )
(2) Changing to the av mode by remote control.(av mode : av1 or av2 or av3)
(3) Display the internal pattern of the VCT-Pro IC by pushing the IN-START.
(4) Stick sensor to center of the screen and select each items (Red/Green/Blue Gain and Offset) using D/E(CH ±) key on R/C.
(5) Adjust R/ G/B Gain using F/G(VOL ±) key on R/C.
(6) Adjust two modes of Cool(Dynamic) and Warm(Mild) as below figure. (Fix the one of R/G/B and change the others)
1) Push the one time the in-start key : Dynamic(Cool)
2) Push the two more the in-start key : Mild(Warm)
(For Manual adjustment)
Adjustment mode : Two modes of Cool (Dynamic) and Warm(Mild) (Medium data is automatically calibrated by the cool data)
Color analyzer(CA110, CA210) should be used in the calibrated ch by CS-1000.(LCD : CH9)
For manual adjustment, it is also possible by the following sequence
Operate the zero-calibration of the CA-110 or CA-210, then stick sensor to the module when adjusting.
(1) Select white pattern of heat-run by pressing “POWER ON” key on remote control for adjustment then operate heat run longer than 15 minutes. (If not executed this step, the condition for W/B will be differ )
(2) Changing to the av mode by remote control.(av mode : av1 or av2 or av3)
(3) Display the internal pattern of the VCT-Pro IC by pushing the IN-START.
(4) Stick sensor to center of the screen and select each items (Red/Green/Blue Gain and Offset) using D/E(CH ±) key on R/C.
(5) Adjust R/ G/B Gain using F/G(VOL ±) key on R/C.
(6) Adjust two modes of Cool(Dynamic) and Warm(Mild) as below figure. (Fix the one of R/G/B and change the others)
1) Push the one time the in-start key : Dynamic(Cool)
2) Push the two more the in-start key : Mild(Warm)
Refer to the below case to know what value is
fixed.
CASE
First adjust the coordinate much away from the target value(x, y).
x,y > target
1) Decrease the R, G.
x,y < target
1) First decrease the B gain.
2) Decrease the one of the others.
In case of decreasing the x, decreasing the R: fix G
In case of decreasing the y, decreasing the G: fix R
x > target, y < target
1) First decrease B, so make y a little more than the target.
2) Adjust x value by decreasing the R
CASE
First adjust the coordinate much away from the target value(x, y).
x,y > target
1) Decrease the R, G.
x,y < target
1) First decrease the B gain.
2) Decrease the one of the others.
In case of decreasing the x, decreasing the R: fix G
In case of decreasing the y, decreasing the G: fix R
x > target, y < target
1) First decrease B, so make y a little more than the target.
2) Adjust x value by decreasing the R
x < target, y > target
1) First decrease B, so make x a little more than the target
2) Adjust x value by decreasing the G.
(7) When adjustment is completed, Exit adjustment mode using EXIT key on R/C.
1) First decrease B, so make x a little more than the target
2) Adjust x value by decreasing the G.
(7) When adjustment is completed, Exit adjustment mode using EXIT key on R/C.
Input the Shipping Option Data
1) Push the ADJ key in a Adjust Remote control.
2) Input the Option Number that was specified in the BOM, into the Shipping area.
3) The work is finished, Push Stp Key.
1) Push the ADJ key in a Adjust Remote control.
2) Input the Option Number that was specified in the BOM, into the Shipping area.
3) The work is finished, Push Stp Key.
