SHARP LC-19LE510E/K _ LC-22LE510E/K _ LC-24LE510E/K _ LED TV _
TROUBLESHOOTING
No Back-light Problem
Problem: If TV is working, led is normal and there is no picture and back-light on the panel.
Possible causes: Back-light pin, dimming pin, back-light supply, stby on/off pin
Back-light pin should be high in open position. If it is low, check Q181 and panel cables.
Problem: If TV is working, led is normal and there is no picture and back-light on the panel.
Possible causes: Back-light pin, dimming pin, back-light supply, stby on/off pin
Back-light pin should be high in open position. If it is low, check Q181 and panel cables.
Dimming
pin should be high or square wave in open position. If it is low, check
S16 for Mstar side and panel or power cables, connectors.
Back-light
power supply should be in panel specs. Check CN705 for MB60, related
connectors for power supply cards.
CI Module Problem
Problem: CI is not working when CI module inserted.
Possible causes: Supply, supply control pin, detect pins, mechanical positions of pins
CI supply should be 5V when CI module inserted. If it is not 5V check CI_POWER_CTRL, this pin should be low.
Problem: CI is not working when CI module inserted.
Possible causes: Supply, supply control pin, detect pins, mechanical positions of pins
CI supply should be 5V when CI module inserted. If it is not 5V check CI_POWER_CTRL, this pin should be low.
Check
mechanical positions of CI module.
Detect ports should be low. If it is not low check CI connector pins, CI module pins and 3V3_VCC on MB60.
Detect ports should be low. If it is not low check CI connector pins, CI module pins and 3V3_VCC on MB60.
Led Blinking Problem
Problem: LED blinking, no other operation
This problem indicates a short on Vcc voltages. Protect pin should be logic high while normal operation.
When there is a short circuit protect pin will be logic low. If you detect logic low on protect pin, unplug the TV set and control voltage points with a multi-meter to find the shorted voltage to ground.
Problem: LED blinking, no other operation
This problem indicates a short on Vcc voltages. Protect pin should be logic high while normal operation.
When there is a short circuit protect pin will be logic low. If you detect logic low on protect pin, unplug the TV set and control voltage points with a multi-meter to find the shorted voltage to ground.
No Sound Problem at Headphone
Problem: No audio at headphone output.
Check HP detect pin, when headphone is. Check 5V_VCC and 3V3_VCC with a voltage-meter.
Check HP detect pin, when headphone is. Check 5V_VCC and 3V3_VCC with a voltage-meter.
No Sound Problem
Problem: No audio at main TV speaker outputs.
Check supply voltages of VDD_AUDIO, 5V_VCC and 3V3_VCC with a voltage-meter.
There may be a problem in headphone connector or headphone detect circuit (when headphone is connected, speakers are automatically muted). Measure voltage at HP_DETECT pin, it should be 3.3v.
Problem: No audio at main TV speaker outputs.
Check supply voltages of VDD_AUDIO, 5V_VCC and 3V3_VCC with a voltage-meter.
There may be a problem in headphone connector or headphone detect circuit (when headphone is connected, speakers are automatically muted). Measure voltage at HP_DETECT pin, it should be 3.3v.
Standby On/Off Problem
Problem: Device cannot boot, TV hangs in standby mode.
There may be a problem about power supply. Check 12V_VCC, 5V_VCC and 3V3_VCC with a volt-meter. Also there may be a problem about SW. Try to update TV with latest SW. Additionally it is good to check SW printouts via hyper-terminal (or Teraterm). These printouts may give a clue about the problem.
Problem: Device cannot boot, TV hangs in standby mode.
There may be a problem about power supply. Check 12V_VCC, 5V_VCC and 3V3_VCC with a volt-meter. Also there may be a problem about SW. Try to update TV with latest SW. Additionally it is good to check SW printouts via hyper-terminal (or Teraterm). These printouts may give a clue about the problem.
No Signal Problem
Problem: No signal in TV mode.
Check tuner supply voltage; 5V_TUN. Check tuner options are correctly set in Service menu. Check AGC voltage at RF_AGC pin of tuner.
Problem: No signal in TV mode.
Check tuner supply voltage; 5V_TUN. Check tuner options are correctly set in Service menu. Check AGC voltage at RF_AGC pin of tuner.
SMPS & LED CONVERTER SCHEMATIC (Vestel PWB is used)
CLICK ON THE PICTURES TO ZOOM IN
