TOSHIBA SP-D4000 – HOW TO REMOVE DISC AT EMERGENCY_DVD MECHANISM DISASSEMBLY

TOSHIBA SD-P4000 14-inch LCD TV/DVD COMBINATION_UNLOCK_DISC REMOVAL AT EMERGENCY_DVD MECHANISM DISASSEMBLE PROCEDURE

DISC REMOVAL METHOD AT NO POWER SUPPLY

> Remove the Back Cabinet.

> Slide the Rack Loading toward the arrow direction by hand to release the lock. (Refer to Fig. 1)
> Take out the Disc from the DVD Deck. Be careful not to scratch on the Disc.

PARENTAL CONTROL - RATING LEVEL - 4 DIGIT PASSWORD CANCELLATIONS

If the stored 4 digit password in the Rating Level menu needs to be cancelled

> Turn Unit ON.
> Press and hold the '7' key on the remote control unit.
> Simultaneously press and hold the 'STOP' key on the front panel.
> Hold both keys for more than 3 seconds.
> The On Screen Display message 'PASSWORD CLEAR' will appear.
> The 4 digit password has now been cleared.

TRAY LOCK

Tray cannot be opened by setting the Tray Lock.

> Turn Unit ON.
> Set the DVD to the Stop Mode.
> Press and hold the '9' key on the remote control unit.
> Simultaneously press and hold the 'STOP' key on the front panel.
> Hold both keys for more than 3 seconds.
> Press the OPEN/CLOSE key on the front panel to check the Tray Lock setting.

NB: No indications on the screen when the Tray Lock is setting.

To unlock the Tray Lock,

> Turn Unit ON.
> Set the DVD to the Stop Mode.
> Set the VOLUME to minimum.
> Press and hold the 'REC/OTR' button on the front panel.
> Simultaneously press and hold the '4' key on the remote control unit.
> Hold both keys for more than 2 second.
> The On Screen Display message 'INITIALIZE COMPLETE' will appear.
The Tray Lock has now been cleared.

NB: The above procedure will reset ALL of the player's settings to the default factory state.

DVD MECHANISM DISASSEMBLE PROCEDURE

LOADING MOTOR ASS'Y/START SW PCB ASS'Y/ END SW PCB ASS'Y

* Remove the 3 screws 1.
* Remove the Loading Motor Ass'y.
* Remove the 2 screws 2.
* Remove the Motor and Loading Worm.
* Disconnect the following connector: (CP2).
* Remove the screw 3.
* Unlock the 2 supports 4 and remove the Start SW PCB Ass'y.
* Unlock the 2 supports 5 and remove the End SW PCB Ass'y.

NOTE: In case of the Loading Worm installation, check if the value of the Fig. 2-1-B is correct.
When installing the wire, install it correctly as Fig.

TRAVERSE UNIT ROD/TRAVERSE UNIT HOLDER/CD DECK/INSULATOR

* Remove the screw 1.
* Remove the Traverse Unit Rod.
* Remove the 2 screws 3.
* Unlock the 2 supports 4 and remove the CD Deck Block.
* Remove the 2 screws 5.
* Unlock the 2 supports 6 and remove the Traverse Unit Holder.
* Remove the 4 Insulators.

MOUTH ASS'Y

Remove the 2 screws 1.
Remove the Mouth Ass'y.

DISC L LEVER/DISC STOPPER/LOCKER STOPPER/ ROLLER GEAR

* Remove the screw 1.
* Remove the Disc L Lever and Disc L Lever Spring.
* Remove the Stopper Spring.
* Unlock the support 2 and remove the Locker Stopper.
* Unlock the support 3 and remove the Disc Stopper.
* Remove the Upper Roller, Roller Rubber and Roller Gear

* In case of the Upper Roller installation, install correctly as Fig.

RACK LOADING/RACK GEAR/GUIDE ARM SPRING/MID RACK GEAR

> Remove the Guide Arm Spring.
> Unlock the 3 supports 1 and remove the Rack Loading.
> Remove the Rack Gear and Mid Rack Gear.

LINK R ASS'Y/LINK L/LINK MID/LINK SPRING

* Remove the screw 1.
* Remove the Link Spring.
* Unlock the support 2 and remove the Link L.
* Unlock the support 3 and remove the Link Mid.
* Remove the screw 4.
* Unlock the 4 supports 5 and remove the Link R Ass’y

ARM ROLLER ASS'Y/MID ROLLER 1/2 GEAR/TERMINAL GEAR

> Remove the screw 1.
> Remove the Arm Roller Ass'y.
> Remove the Terminal Gear and Mid Roller Gear 1.
> Unlock the support 2 and remove the Mid Roller Gear 2.

CLAMPER ASS'Y/DISC GUIDE ARM/DISC R LEVER

* Unlock the support 1 and remove the Clamper Ass'y.
* Unlock the support 2 and remove the Disc Guide Arm.
* Unlock the support 3 and remove the Disc R Lever.

When installing the Clamper Ass'y, check if the Clamper Ass'y is locked correctly as Fig

EXPLODED VIEW

CLICK ON THE PICTURES TO MAGNIFY