UA40C6200UR _ UA46C6200UR _ UA55C6200UR
UA32C6900V* _ UA40C6900V* _ UA46C6900V*
_ UA55C6900V*
Universal Remote Control Set-up Codes to Check with Samsung Brand TVs
Universal Remote Control Set-up Codes to Check with Samsung Brand TVs
SERVICE MODE
How
to Access Service Mode; Using the Customer Remote
1. Turn the power off and set to stand-by mode
2. Press the remote buttons in this order; POWER OFF - INFO - MENU - MUTE - POWER ON to turn the set on.
3. The set turns on and enters service mode. This may take approximately 20 seconds.
4. Press the Power button to exit and store data in memory. - If you fail to enter service mode, repeat steps 1 and 2 above.
1. Turn the power off and set to stand-by mode
2. Press the remote buttons in this order; POWER OFF - INFO - MENU - MUTE - POWER ON to turn the set on.
3. The set turns on and enters service mode. This may take approximately 20 seconds.
4. Press the Power button to exit and store data in memory. - If you fail to enter service mode, repeat steps 1 and 2 above.
Buttons operations within Service
Mode
Menu > Full Menu Display/Move
to Parent Menu
Direction Keys Up / Dn > Item Selection by Moving the Cursor
Direction Keys Up/Dn > Data Increase / Decrease for the Selected Item
Source > Cycles through the
active input source that are connected to the unit
Initial
SERVICE MODE DISPLAY State. Mode: CDTV . RES : 480I
Upgrading the Software
1. Insert a USB drive
containing the firmware upgrade into the Wiselink Pro port on the side of the
TV.
2. If pop up is showed, press the exit or press the No button. (If you press Yes button, display is changed to Wiselink Pro Menu )
3. Press the MENU button to display the menu. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button.
4. Press the ▲ or ▼ button to select “SW Upgrade”, then press the ENTER button.
5. Press the ENTER button. The message “Scanning for USB... It may take up to 30 seconds.” is displayed.
6. The message “Upgrade version XXXX to version XXXX? The system will be reset after upgrade.” is displayed. Press the ◄ or ► to select the “OK”, then press the ENTER button.
[Be careful to not disconnect the power or remove the USB drive while upgrades are being applied. The TV will turn off and turn on automatically after completing the firmware upgrade. Check the firmware version after the upgrades are complete. When software is upgraded, video and audio settings you have made will return to their default (factory) settings.]
2. If pop up is showed, press the exit or press the No button. (If you press Yes button, display is changed to Wiselink Pro Menu )
3. Press the MENU button to display the menu. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button.
4. Press the ▲ or ▼ button to select “SW Upgrade”, then press the ENTER button.
5. Press the ENTER button. The message “Scanning for USB... It may take up to 30 seconds.” is displayed.
6. The message “Upgrade version XXXX to version XXXX? The system will be reset after upgrade.” is displayed. Press the ◄ or ► to select the “OK”, then press the ENTER button.
[Be careful to not disconnect the power or remove the USB drive while upgrades are being applied. The TV will turn off and turn on automatically after completing the firmware upgrade. Check the firmware version after the upgrades are complete. When software is upgraded, video and audio settings you have made will return to their default (factory) settings.]
Self Diagnostic
This is simple test function that judge whether is TV SET’s problem or not.
There are two self-test. Picture and Sound.
1. Press “Menu > Support > Self Diagnosis” The message “Picture Test / Sound Test” is displayed.
This is simple test function that judge whether is TV SET’s problem or not.
There are two self-test. Picture and Sound.
1. Press “Menu > Support > Self Diagnosis” The message “Picture Test / Sound Test” is displayed.
2. Picture Test
1 The message “Does the problem still exist with this test pattern?” is displayed.
2 Press “Yes”. This is a TV SET problem. The massage “Contact Samsung’s call center at 1-800-SAMSUNG for assistance.” is displayed.
3 Press “No”. This is not a TV SET problem.
The message “If the self diagnosis picture is OK, picture distortion may cause by your external device. Check connection. If the problem still persists, refer to the external device’s user manual.” is displayed.
1 The message “Does the problem still exist with this test pattern?” is displayed.
2 Press “Yes”. This is a TV SET problem. The massage “Contact Samsung’s call center at 1-800-SAMSUNG for assistance.” is displayed.
3 Press “No”. This is not a TV SET problem.
The message “If the self diagnosis picture is OK, picture distortion may cause by your external device. Check connection. If the problem still persists, refer to the external device’s user manual.” is displayed.
Sound Test
1 The message “Does the problem still exist with this sound test?” is displayed.
2 Press “Yes”. This is a TV SET problem. The message “Contact Samsung’s call center at 1-800-SAMSUNG for assistance. “is displayed
3 Press “No”. This is not a TV SET problem. The message “If the self diagnosis picture is OK, picture distortion may caused by your external device. Check connection. If the problem still persists, refer to the external device’s user manual.” is displayed.
1 The message “Does the problem still exist with this sound test?” is displayed.
2 Press “Yes”. This is a TV SET problem. The message “Contact Samsung’s call center at 1-800-SAMSUNG for assistance. “is displayed
3 Press “No”. This is not a TV SET problem. The message “If the self diagnosis picture is OK, picture distortion may caused by your external device. Check connection. If the problem still persists, refer to the external device’s user manual.” is displayed.
UNIVERSAL REMOTE CONTROL SET-UP CODES
0030 0049 0050 0066 0076 0101 0102 0119 0143 0152 0154 0166 0181 0195 0209 0217 0240 0307 0318 0365 0379 0414 0421 0488 0492 0601 0624 0637 0642 0827
0030 0049 0050 0066 0076 0101 0102 0119 0143 0152 0154 0166 0181 0195 0209 0217 0240 0307 0318 0365 0379 0414 0421 0488 0492 0601 0624 0637 0642 0827