Philips HTS5131 BD Home Theater System – BD loading tray replacement – Firmware update – SMPS and Power Amplifier section circuit diagram
How to replace the defective Blu-ray Loader
a) Remove the defective Blu-ray Loader.
b) Loosen 2 screws “A” on the top of BD loader jack PCB to remove the board as shown below.
c) Loosen 4 screws “B” to take out the “Sanyo TRV-414H05” as shown below.
d) Blu-ray Loader to connect “HA802” on the top of BD Board as shown below.
Note: The 2 ESD protection points on any one side must be soldered if the Blu-ray Loader is OK and needs to be disconnected from connector HA802 of the BD Board.
Press <Home> button on R/C.
b) Select <Setup>, then press “OK” button on R/C.
c) Select <Preference>, then press <OK> button on R/C.
d) Select <Menu language>, then press <OK> button on R/C.
C) Select <English>, then press <OK> button on R/C.
Restore factory setting
a) Press <Home> button on R/C.
b) Select <Setup>, then press “OK” button on R/C.
c) Select <Advanced>, then press < OK > button on R/C.
d) Select <Restore default settings>,then press <OK> to confirm.
Password change
a) Press <Home> button on R/C.
b) Select <Setup>, then press “OK” button on R/C.
c) Select <Preference>, then press <OK> button on R/C.
d) Select <Change Password> <Confirm>, then press <OK> button on R/C.
“0000” is default password supplied.
Trade
mode
a) In open model,press <Home> button on R/C.
b) Press “2” “5” “9” on R/C,VFD will display “TRA ON” or “TRA OFF”.
a) In open model,press <Home> button on R/C.
b) Press “2” “5” “9” on R/C,VFD will display “TRA ON” or “TRA OFF”.
Check
software version
a) Press <Home> button on R/C
b) Select <Setup>, then press <OK> button on R/C.
c) Select <Advanced> <Version Info.>,then press <OK> button on R/C
a) Press <Home> button on R/C
b) Select <Setup>, then press <OK> button on R/C.
c) Select <Advanced> <Version Info.>,then press <OK> button on R/C
d)
Select <Close> on the version display screen and press <OK> button
to exit .
Upgrading
new software
Method 1: Update software from a USB storage device
a) Create a folder named “UPG_ALL” in your USB storage device, and Copy the latest upgrading software into the folder.
b) Connect the USB storage device to the home theater.
c) Press <Home> button on R/C, and select <Setup>.
d) Select <Advanced> <Software Update> <USB>.
e) TV will show message as follow:
Method 1: Update software from a USB storage device
a) Create a folder named “UPG_ALL” in your USB storage device, and Copy the latest upgrading software into the folder.
b) Connect the USB storage device to the home theater.
c) Press <Home> button on R/C, and select <Setup>.
d) Select <Advanced> <Software Update> <USB>.
e) TV will show message as follow:
"Now searching for upgrade software! Please wait...!”
“Software updates for this player have been found. Do you want to upgrade?”
f) Select <Start>, press <OK> button on R/C.
Software upgrade will take 5 minutes
Do not switch off!
Package version: 000025.0
Software BE 80%
Software FE Completed
Software MCU1:
Software Dock:
Software MCU3
Software upgrade will take 5 minutes
Do not switch off!
Package version: 000025.0
Software BE Completed
Software FE Completed
Software MCU1: Not started
Software Dock: 2%
Software MCU3: Not started
Software upgrade will take 5 minutes
Do not switch off!
Package version: 000025.0
Software BE Completed
Software FE Completed
Software MCU1: 1%
Software Dock: Failed
Software MCU3:
The set will shut down automatically when the software upgrade is completed.
Update software from the internet
Note: To check for new updates, compare the current software version of your home theater with the latest software version (if available) on the Philips web site, and for BD-Live application and software update, make sure that the network router has access to
the Internet and the firewall is disabled.
a) The b) Press “ ” <Home> button on R/C, and select <Setup>.
b) Press “ ” <Home> button on R/C, and select <Setup>.
c) Select <Advance Setup> <Software Update> <Network>.
Follow the on-screen instructions.
