Panasonic Viera - TH-32A400H TH-32A410H - HONG KONG – TH 42A410T THAILAND - How to enter Service Mode – Hotel Mode – Power LED Blinking - Power Supply Circuit Diagram.
How to enter into Service ModeWhile pressing [VOLUME (--)] button of the main unit, press [INFO] button of the remote control three times within 2 seconds.
Key command
[1] button...Main items Selection in forward direction
[2] button...Main items Selection in reverse direction
[3] button...Sub items Selection in forward direction
[4] button...Sub items Selection in reverse direction
[VOL] button...Value of sub items change in forward direction ( + ), in reverse direction ( - )
How to exit
Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.
Contents
of adjustment mode
> Value is shown as a hexadecimal number.
> Preset value differs depending on models.
> After entering the adjustment mode, take note of the value in each item before starting adjustment.
Service
mode screen> Value is shown as a hexadecimal number.
> Preset value differs depending on models.
> After entering the adjustment mode, take note of the value in each item before starting adjustment.
Display
of SOS History
SOS History (Number of LED blinking) indication.
From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment. This indication except 2nd and 1st occurrence after shipment will be cleared by [Self-check indication and forced to factory
shipment setting].
SOS History (Number of LED blinking) indication.
From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment. This indication except 2nd and 1st occurrence after shipment will be cleared by [Self-check indication and forced to factory
shipment setting].
Exit
Disconnect the AC cord from wall outlet.
Disconnect the AC cord from wall outlet.
Hotel
Mode
Access command to the Hotel mode setup menu.
In order to display the Hotel mode setup menu:
While pressing [VOLUME (-)] button of the main unit,
press [AV] button of the remote control three times within 2 seconds. The Hotel mode setup menu is displayed.
Access command to the Hotel mode setup menu.
In order to display the Hotel mode setup menu:
While pressing [VOLUME (-)] button of the main unit,
press [AV] button of the remote control three times within 2 seconds. The Hotel mode setup menu is displayed.
To
exit the Hotel mode setup menu
Disconnect AC power cord from wall outlet.
Disconnect AC power cord from wall outlet.
The
self-check function to test the unit.
Checking the IIC bus lines
Power LED Blinking timing.
Checking the IIC bus lines
Power LED Blinking timing.
How
to access. Self-check indication only
Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [OK] button on the remote control for more than 3 seconds.
Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [OK] button on the remote control for more than 3 seconds.
Self-check
indication and forced to factory shipment setting
Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote control for more than 3 seconds.
Exit - Disconnect the AC cord from wall outlet.
Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote control for more than 3 seconds.
Exit - Disconnect the AC cord from wall outlet.
SMPS CIRCUIT DIAGRAM (Schematic) [TNP 4G572] Hong Kong
TNPA5916ED
– Power board Schematic. TH 42A410T THAILAND
Power
LED Blinking timing chart
Information of LED Flashing timing chart.
When an abnormality occurs, the protection circuit will operate and reset the unit to stand by mode. During this time, the defective block can be identified by the number of blinking times of the Power LED on the front panel of the unit.
When an abnormality occurs, the protection circuit will operate and reset the unit to stand by mode. During this time, the defective block can be identified by the number of blinking times of the Power LED on the front panel of the unit.
BL_SOS
- SOS from PANEL inverter - 1 Blink
TV_SOS
- TCON power down – 3 Blinks
SOUND_SOS
-SOS from audio AMP – 9 Blinks
LCD Panel test mode
To find the possible failure point where in LCD Panel or Printed Circuit Board when the abnormal picture is displayed.
To Enter
While pressing [VOLUME ( - )] button of the main unit, press [OPTION] button of the remote control three times within 2 seconds.
To Exit; Disconnect AC plug from wall outlet.
To confirm
If the abnormal picture is displayed, go into LCD Panel test mode to display the several test patterns.
And then, judge by the following method.
Still abnormal picture is displayed: The cause must be in LCD Panel.
Normal picture is displayed: The cause must be in A board.
Remarks
The test pattern is created by the circuit in LCD Panel.
In LCD Panel test mode, this test pattern is displayed unaffected by signal processing for RF or input signal.
If the normal picture is displayed, LCD Panel must be okay and the cause of failure must be in A board.
