Sony RCD W500C US Model Canadian Model COMPACT DISC RECORDER - Self diagnosis - Program setting - Circuit diagram
Self-diagnosis FunctionWhen the self-diagnosis function is activated to prevent the player from malfunctioning, three character service numbers in a combination with a message appears in the display.
C12/ Cannot Copy: You are trying to record a disc that cannot be played back in DECK-A or with an external device, such as CD-ROM or VIDEO CD.
• Remove the disc, and then insert a music CD for playback.
C13/ Rec Error: Recording has not been completed successfully because of vibration.
• Relocate the unit in a place free of vibration and restart the recording again.
The disc you try to record is excessively dirty (such as oil stained or finger marked) or scratched. Or the disc is not normal.
• Replace the disc with another one and restart the recording again.
C14/TOC Error: The unit did not read the TOC information.
• Insert other discs.
C41/Cannot Copy: The sound source you are trying to record is a copy of commercial music software. Or you are trying to record on a CD-R/CD-RW digitally.
• Because of the restriction of the Serial Copy Management System, you cannot record a copy of commercial music software. Neither can you record a CD-R/CD-RW digitally.
C71/ Din Unlock: If this message is displayed momentarily, this is not an error. It is caused by the digital signal during recording.
During recording of a digital sound source, the connecting cable has been disconnected or the player of the sound source has turned off.
• Connect the cable or turn on the digital player.
The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. The emission check enables continuous checking of the S curve.
Schematic
BD Board
CDR Board
Display Board
Main board
Setting
of Programs
Confirmation
of System (Windows 98 is used in this explanation) Preparation for Terminal
software
Set
up the serial port from OS.
a) Select Start > Settings > Control Panel and select System > Device manager > Communication Port (COMn)
* Specify the COM port that connected with JIG of CDM65.
a) Select Start > Settings > Control Panel and select System > Device manager > Communication Port (COMn)
* Specify the COM port that connected with JIG of CDM65.
Double
click COMn (as you connect to the Jig-CDM65)
Set the parameters.
Bits per second : 38400
Data bits : 8
Parity : non
Stop bits : 1
Flow control : hardware
Press
“Advanced...” button. Remove the check “Use FIFO buffers ...”Set the parameters.
Bits per second : 38400
Data bits : 8
Parity : non
Stop bits : 1
Flow control : hardware
2) Unzip the file “ttermp23.zip” by PC.
(The file “ttermp23.zip” is distributed together with the service manual.)
3) After unzip the files, you can find setup.exe.
Double click the setup.exe.
Install as the installer is.
Do not change the directory that files are installed. (use default)
4) Unzip the file “030416_Service.zip” by PC.
Copy all “ttl” file and “FUNC” folder which are contained in “030416_Service” and paste them in the “Ttermpro” file as below.
(The file “030416_Service.zip” is distributed together with the service manual.)
Note: Do not change the directory path.
5)
Start-up the TeraTermPro
Double click the ttermpro.exe.
6) Set up the TeraTermPro (IMPORTANT)
a) Select Setup > Serial Port... and set the parameters as below.
Port : (As you connect to the Jig-CDM65)
Baud rate : 38400
Data : 8 bit
Parity : none
Stop : 1 bit
Flow control : hardware
Transmit delay : 0 msec/char 10 msec/line
After settings, press “OK” button.
Double click the ttermpro.exe.
6) Set up the TeraTermPro (IMPORTANT)
a) Select Setup > Serial Port... and set the parameters as below.
Port : (As you connect to the Jig-CDM65)
Baud rate : 38400
Data : 8 bit
Parity : none
Stop : 1 bit
Flow control : hardware
Transmit delay : 0 msec/char 10 msec/line
After settings, press “OK” button.
b)
Terminal setup
Set the parameters as below.
New-line receive : CR
transmit : CR
After settings, press “OK” button.
Set the parameters as below.
New-line receive : CR
transmit : CR
After settings, press “OK” button.
c)
General setup
Select the language and press “OK” button.
Select the language and press “OK” button.
d)
Saving the setup
Select Setup > Save setup... and save as teraterm.ini in the
Ttermpro directory.
Select Setup > Save setup... and save as teraterm.ini in the
Ttermpro directory.
7)
Connect the JIG and CDM65.
8) Confirm the S510 on JIG is ‘CONTROL’.
9) Power on the CDM65 and press SW101(RESET) on JIG.
“CDM65-RBD1 has connected with this PC (^^)” is displayed.
If above message is not displayed, you may have some mistakes.
Confirm previous setting procedures again.
8) Confirm the S510 on JIG is ‘CONTROL’.
9) Power on the CDM65 and press SW101(RESET) on JIG.
“CDM65-RBD1 has connected with this PC (^^)” is displayed.
If above message is not displayed, you may have some mistakes.
Confirm previous setting procedures again.
