Applicable to Samsung LED LCD TVs
UE40D500*BW - UE26D400*BW - UE32D400*BW
UE22D500*BW - UE19D400*BW - UE22D500*BW
UE19D400*BW - LE32D400E1W - LE32D40*E2W
LE40D50*F7W
Entering
Factory Mode
To
enter ‘Service Mode’ Press the remote -control keys in this sequence :
If you do not have Factory remote - control
Power OFF > INFO > MENU > MUTE > Power ON
Power OFF > INFO > MENU > MUTE > Power ON
If
you have Factory remote - control
INFO > FACTORY KEY
INFO > FACTORY KEY
Using
the Customer Remote
1. Turn the power off and set to stand-by mode.
2. Press the remote buttons in this order; POWER OFF- INFO - MENU - MUTE to turn the set on.
3. The set turns on and enters service mode. This may take approximately 20 seconds.
4. Press the Power button to exit and store data in memory.
- If you fail to enter service mode, repeat steps 1 and 2 above.
5. Initial SERVICE MODE DISPLAY State
1. Turn the power off and set to stand-by mode.
2. Press the remote buttons in this order; POWER OFF- INFO - MENU - MUTE to turn the set on.
3. The set turns on and enters service mode. This may take approximately 20 seconds.
4. Press the Power button to exit and store data in memory.
- If you fail to enter service mode, repeat steps 1 and 2 above.
5. Initial SERVICE MODE DISPLAY State
How
to enter the hidden factory mode.
a. into the factory mode
b. move the tap to Advanced
c. key input : 0 + 0 + 0 + 0
** hidden menu : Advanced.
a. into the factory mode
b. move the tap to Advanced
c. key input : 0 + 0 + 0 + 0
** hidden menu : Advanced.
Buttons operations within Service Mode
Menu: Full Menu Display/Move to Parent Menu
Direction Keys Up/Dn: Item Selection by Moving the Cursor
Direction Keys L/R: Data Increase / Decrease for the Selected Item
Source: Cycles through the active input source that are connected to the unit.
W/B initial data values
USB Download Method (Main SW & e-Manual)
Samsung may offer upgrades for TV’s firmware in the future.
Upgrades will be possible by connecting a USB drive to the USB port located on your TV.
1. Insert a USB drive containing the firmware (T-MSU4DEUC) upgrade into the USB port on the rear of the TV.
2. Press the MENU button to display the menu. Press the Up/Dn button to select "Support", then press the ENTER button.
3. Press the or button to select "Software Upgrade", then press the ENTER button to select "By USB". The message "Scanning for USB. It may take up to 1 minute." is displayed.
4. The message "Upgrade version XXXX to version XXXX?
The system will be reset after upgrade." is displayed.
Press the or to select the "OK", then press the ENTER button.
Please be careful to not disconnect the power or remove the USB drive while upgrades are being applied. The TV will turn off and turn on automatically after completing the firmware upgrade.
Please check the firmware version after the upgrades are complete. When software is upgraded, video and audio settings you have made will return to their default (factory) settings.
Write down your settings so that you can easily reset them after the upgrade.
How
To Upgrade Sub Micom
Sub S/W (in Factory mode)
If you don't have DDC Manager, Use this method.
1. Into the Factory Mode.
2. Select "SVC". (Use > button.)
3. Select "MICOM UPGRADE off". (use > button.)
4. If message change from "off" to "wait", TV is upgrading Sub S/W. (It takes about 5 min.)
5. If update completes, TV set will booting automatically.
Sub S/W (in Factory mode)
If you don't have DDC Manager, Use this method.
1. Into the Factory Mode.
2. Select "SVC". (Use > button.)
3. Select "MICOM UPGRADE off". (use > button.)
4. If message change from "off" to "wait", TV is upgrading Sub S/W. (It takes about 5 min.)
5. If update completes, TV set will booting automatically.
