How to Access Service Mode
Using the Customer Remote
* Turn the power off and set to stand-by mode
* Press the remote buttons in this order; POWER OFF- INFO - MENU - MUTE to turn the set on.
The set turns on and enters service mode. This may take approximately 20 seconds.
* Press the Power button to exit and store data in memory.
- If you fail to enter service mode, repeat steps 1 and 2 above.
How to enter the hidden factory mode.
a. into the factory mode
b. move the tap to Advanced
c. key input : 0 + 0 + 0 + 0
** hidden menu : Advanced
Initial SERVICE MODE DISPLAY State & Buttons operations with Service Mode
Using the Customer Remote
* Turn the power off and set to stand-by mode
* Press the remote buttons in this order; POWER OFF- INFO - MENU - MUTE to turn the set on.
The set turns on and enters service mode. This may take approximately 20 seconds.
* Press the Power button to exit and store data in memory.
- If you fail to enter service mode, repeat steps 1 and 2 above.
a. into the factory mode
b. move the tap to Advanced
c. key input : 0 + 0 + 0 + 0
** hidden menu : Advanced
Initial SERVICE MODE DISPLAY State & Buttons operations with Service Mode
White
Balance – Adjustment
Equipment : CS-210
> Pattern: MIK K-7256 #92 “Flat W/B Pattern” as standard
> Use other equipment only after comparing the result with that of the Master equipment.
> Set Aging time : 60min.
> Calibration and Manual setting for WB adjustment.
HDMI : Calibration at #24 Chessboard Pattern Manual adjustment #92 pattern (720p)
COMP: Calibration at #24 Chessboard Pattern Manual adjustment at #92 pattern (720p)
CVBS: Calibration at #24 Chessboard Pattern Manual adjustment at #92 pattern (PAL)
If finishing in HDMI mode, adjustment coordinate is almost same in AV/COMP mode.
White Balance Manual Adjustment
Anynet+:
Anynet+ is an AV network system that enables you to control all connected Samsung AV devices with the TV’s remote.
To directly connect to TV
Connect the [HDMI 1], [HDMI 2] or [HDMI ] jack on the TV and the HDMI OUT jack of the corresponding Anynet+ device using an HDMI cable.
To connect to Home Theater
* Connect the [HDMI 1], [HDMI 2] or [HDMI ] jack on the TV and the HDMI OUT jack of the corresponding Anynet+ device using an HDMI cable.
* Connect the HDMI IN jack of the home theater and the HDMI OUT jack of the corresponding Anynet+ device using the HDMI cable.
* Connect the Optical cable between [Digital Audio Out (Optical)] on your TV and Digital Audio Input on the Home Theater.
* When following the connection above, the Optical jack only outputs 2 channel audio. You will only hear sound from the Home Theater’s Front Left and Right speakers and the sub-woofer. If you want to hear 5.1 channel audio connect the DIGITAL AUDIO OUT (OPTICAL) jack on the DVD / Satellite Box (ie Anynet Device 1 or 2) directly to the Amplifier or Home Theater, not the TV.
Connect only one Home Theater.
- You can connect an Anynet+ device using the HDMI 1.3 cable. Some HDMI cables may not support Anynet+ functions.
Anynet+ works when the AV device supporting Anynet+ is in the Standby or On status.
Anynet+ supports up to 12 AV devices in total. Note that you can connect up to 3 devices of the same type.
Firmware update - USB Download Method
* Insert a USB drive containing the firmware upgrade into the USB port on the rear of the TV.
* Press the MENU button to display the menu.
* Press the Up or Dn button to select “Support”, then press the ENTER button.
* Press the Up or Dn button to select “SW Upgrade”, then press the ENTER button.
The message “Scanning for USB. It may take up to 30 seconds.” is displayed.
The message “Upgrade version XXXX to version XXXX?
The system will be reset after upgrade.” is displayed.
* Press the Left or Right to select the “OK”, then press the ENTER button.
Be careful to not disconnect the power or remove the USB drive while upgrades are being applied. The TV will turn off and turn on automatically after completing the firmware upgrade.
Check the firmware version after the upgrades are complete. When software is upgraded, video and audio settings that you have made will return to their default (Factory) settings.
Recommend you write down your settings so that you can easily reset them after the upgrade.
SMPS – BN44-00216A - Circuit diagram given by the previous post here.
