Applicable to - Panasonic TH-P50XT50A TH-P50XT50D TH-P50XT50G
TH-P50XT50K TH-P50XT50M TH-P50XT50P TH-P50XT50S TH-P50XT50V
Service Mode - Service Tool Mode - Data-copy - LED Blinking Codes details
After exchange parts, check and adjust the contents of adjustment
mode.
While pressing [VOLUME ( - )] button of the main unit, press [i]
button of the remote control three times within 2 seconds.
Note: Service Mode cannot be
entered when 3D signal input. Input 2D
signal to enter Service Mode.
KEY COMMANDS
1 button...Main items Selection in forward direction
2 button...Main items Selection in reverse direction
3 button...Sub items Selection in forward direction
4 button...Sub items Selection in reverse direction
RED button...All Sub items Selection in reverse direction
GREEN button...All Sub items Selection in forward direction
VOL button...Value of sub items change in forward direction ( + ), in reverse direction ( - )
2 button...Main items Selection in reverse direction
3 button...Sub items Selection in forward direction
4 button...Sub items Selection in reverse direction
RED button...All Sub items Selection in reverse direction
GREEN button...All Sub items Selection in forward direction
VOL button...Value of sub items change in forward direction ( + ), in reverse direction ( - )
How to exit
Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.
Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.
Contents of adjustment mode
* Value is shown as a hexadecimal number.
* Preset value differs depending on models.
After entering the adjustment mode, take note of the value in each item before starting adjustment.
* Value is shown as a hexadecimal number.
* Preset value differs depending on models.
After entering the adjustment mode, take note of the value in each item before starting adjustment.
PRE-SET DATA VALUES
Option - Mirror
Picture can be reversed left and right or up and down.
00 : Default (Normal picture is displayed)
01 : Picture is reversed left and right.
02 : Picture is reversed up and down.
Picture can be reversed left and right or up and down.
00 : Default (Normal picture is displayed)
01 : Picture is reversed left and right.
02 : Picture is reversed up and down.
If the defective symptom (e.g. Vertical bar or Horizontal bar) is
moved by selection of this mirror, the possible cause is in A-board.
SERVICE TOOL MODE
Select [SRV-TOOL] in Service Mode.
Press [OK] button on the remote control.
Press [OK] button on the remote control.
Display of SOS History
SOS History (Number of LED blinking) indication.
From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment. This indication except 2nd and 1st occurrence after shipment will be cleared by [Self-check indication and forced to factory shipment setting].
SOS History (Number of LED blinking) indication.
From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment. This indication except 2nd and 1st occurrence after shipment will be cleared by [Self-check indication and forced to factory shipment setting].
POWER ON TIME/COUNT
Note : To display TIME/COUNT menu, highlight position, then press MUTE for 3 sec.
Time : Cumulative power on time, indicated hour : minute by decimal
Count : Number of ON times by decimal
Note : This indication will not be cleared by either of the self-checks or any other command.
Note : To display TIME/COUNT menu, highlight position, then press MUTE for 3 sec.
Time : Cumulative power on time, indicated hour : minute by decimal
Count : Number of ON times by decimal
Note : This indication will not be cleared by either of the self-checks or any other command.
Exit
Disconnect the AC cord from wall outlet.
Disconnect the AC cord from wall outlet.
DRV Check - USBHDD Check
Select [DRV Check - USBHDD Check] in Service Mode.
Press [OK] button on the remote control for more than 3 seconds.
Select [DRV Check - USBHDD Check] in Service Mode.
Press [OK] button on the remote control for more than 3 seconds.
Hotel mode
In order to display the Hotel mode setup menu: While pressing [VOLUME (-)] button of the main unit, press [AV] button of the remote control three times within 2 seconds.
In order to display the Hotel mode setup menu: While pressing [VOLUME (-)] button of the main unit, press [AV] button of the remote control three times within 2 seconds.
To exit the Hotel mode setup menu: Disconnect AC power cord from
wall outlet.
Data Copy by SD Card
Board replacement (Copy the data when
exchanging A-board)
When exchanging A-board, the data in original A-board can be copied to SD card and then copy to new A-board.
When exchanging A-board, the data in original A-board can be copied to SD card and then copy to new A-board.
Hotel (Copy the data when installing a
number of units in hotel or any facility)
When installing a number of units in hotel or any facility, the data in master TV can be copied to SD card and then copy to other TVs.
When installing a number of units in hotel or any facility, the data in master TV can be copied to SD card and then copy to other TVs.
Preparation
Make pwd file as startup file for (a) or (b) in a empty SD card.
> Insert a empty SD card to your PC.
> Right-click a blank area in a SD card window, point to New, and then click text document. A new file is created by default (New Text Document.txt).
> Right-click the new text document that you just created and select rename, and then change the name and extension of the file to the following file name for (a) or (b) and press ENTER. File name:
a For Board replacement : boardreplace.pwd
b For Hotel : hotel.pwd
Make pwd file as startup file for (a) or (b) in a empty SD card.
> Insert a empty SD card to your PC.
> Right-click a blank area in a SD card window, point to New, and then click text document. A new file is created by default (New Text Document.txt).
> Right-click the new text document that you just created and select rename, and then change the name and extension of the file to the following file name for (a) or (b) and press ENTER. File name:
a For Board replacement : boardreplace.pwd
b For Hotel : hotel.pwd
Note:
Make only one file to prevent the operation error.
No any other file should not be in SD card.
No any other file should not be in SD card.
Data copy from TV set to SD Card
> Turn on the TV set.
> Insert SD card with a startup file (pwd file) to SD slot. On-screen Display will be appeared according to the startup file automatically.
> Input a following password for (a) or (b) by using remote control.
a For Board replacement: 2770
b For Hotel: 4850
Data will be copied from TV set to SD card. It takes around 2 to 6 minutes maximum for copying.
> After the completion of copying to SD card, remove SD card from TV set.
> Turn off the TV set.
> Turn on the TV set.
> Insert SD card with a startup file (pwd file) to SD slot. On-screen Display will be appeared according to the startup file automatically.
> Input a following password for (a) or (b) by using remote control.
a For Board replacement: 2770
b For Hotel: 4850
Data will be copied from TV set to SD card. It takes around 2 to 6 minutes maximum for copying.
> After the completion of copying to SD card, remove SD card from TV set.
> Turn off the TV set.
Note:
Following new folder will be created in SD card for data from TV set.
a For Board replacement : user_setup
b For Hotel : hotel.
Following new folder will be created in SD card for data from TV set.
a For Board replacement : user_setup
b For Hotel : hotel.
Data copy from SD Card to TV set
> Turn on the TV set.
> Insert SD card with Data to SD slot. On-screen Display will be appeared according to the Data folder automatically.
> Input a following password for (a) or (b) by using remote control.
a For Board replacement : 2771
b For Hotel : 4851
Data will be copied from SD card to TV set.
> After the completion of copying to SD card, remove SD card from TV set.
a For Board replacement: Data will be deleted after copying (Limited one copy).
b For Hotel: Data will not be deleted and can be used for other TVs.
> Turn off the TV set.
> Insert SD card with Data to SD slot. On-screen Display will be appeared according to the Data folder automatically.
> Input a following password for (a) or (b) by using remote control.
a For Board replacement : 2771
b For Hotel : 4851
Data will be copied from SD card to TV set.
> After the completion of copying to SD card, remove SD card from TV set.
a For Board replacement: Data will be deleted after copying (Limited one copy).
b For Hotel: Data will not be deleted and can be used for other TVs.
> Turn off the TV set.
Depending on the failure of boards, function of Data copy for
board replacement does not work.
This function can be effective among the same model numbers.
This function can be effective among the same model numbers.
Power LED Blinking timing chart
Information of LED Flashing timing chart.
When an abnormality has occurred the unit, the protection circuit operates and reset to the standby mode. At this time, the defective block can be identified by the number of blinks of the Power LED on the front panel of the unit.
Information of LED Flashing timing chart.
When an abnormality has occurred the unit, the protection circuit operates and reset to the standby mode. At this time, the defective block can be identified by the number of blinks of the Power LED on the front panel of the unit.
CLICK ON THE PICTURES TO ZOOM IN
