How to upgrade the Firmware - Connector Voltages and Functions - USB upgrade - Board Connections - SAMSUNG FX-2490HD - TFT LCD Monitor
> CN1404(Full HD) - Transmits LVDS signals from the Main board to
the panel * When a problem occurs: The Blank Screen and No Power errors may
occur.
> CN902 - VGA signal input terminal * when a problem occurs: The
No RGB Output error may occur.
> CN1002, CN1003 - HDMI&DVI signal input terminal * when a
problem occurs: The No HDMI&DVI Output error may occur.
> CN210 - Supplies 14V from the Power adapter to the Main board. *
When a problem occurs: The Blank Screen and No Power errors may occur.
> CN802 - Component video input terminal. * When a problem occurs:
The No MIC Input error may occur.
> CN901 - PC Audio input terminal. * When a problem occurs: The No
Speaker Output error may occur.
> OP1301 - Digital Audio output terminal. * When a problem occurs:
The No USB Download Operating error may occur.
> CN1301 - Headphone output terminal.
> CN801 - Component Audio input terminal. Composite Video input
terminal. * When a problem occurs: The No Speaker Output error may occur.
LVDS 30P FFC cable – Code BN96-12453X
MAIN BOARD CONNECTORS
SOFTWARE UPGRADE
Program Upgrade – Main
> Select MENU > Support > Software Upgrade on remote control,
you’ll see below picture.
> Press ENTER.
Micom program is now upgrading message will be displayed.
After Software Upgrade is process by 100%, the monitor is
automatically turned off and on.
Micom Program Upgrade
DDC Manager Connection
> Prepare PC to Upgrade the Program.
> Prepare the DDC Manager
> Connect D-sub cable to Target Monitor TV
> Power on the Target Monitor TV
> Connect D-sub cable to Target Monitor TV
> Power on the Target Monitor TV
winDDC_V2-39 Program installed
Run winDDC
SUB-MICOM UPGRADE
> Select WinISP Menu
> Make same setting like picture.
> Choose Device Type.
WT61P8
> Choose Device Type.
WT61P8
> Load File ( Select file to download)
> Set Option to load Binary Files
> Select files (hex file)
> Click button to load files
> Set Option to load Binary Files
> Select files (hex file)
> Click button to load files
> Check the OK message (Load)
> Click Auto Program button
> If you see OK message (Verify), program download is completed.
> Click Auto Program button
> If you see OK message (Verify), program download is completed.
USB Download Method
Samsung may offer upgrades for TV’s firmware in the future.
Upgrades will be possible by connecting a USB drive to the USB port located on
your TV.
> Insert a USB drive containing the firmware upgrade into the USB
port on the rear of the TV.
> Press the MENU button to display the menu. Press the ▲/▼ button to select “Support”, then press the ENTER button.
> Press the ▲/▼ button to select “SW Upgrade”, then press the ENTER button. The message “Scanning for USB. It may take up to 30 seconds.” is displayed.
> The message “Upgrade version XXXX to version XXXX?
The system will be reset after upgrade.” is displayed.
> Press the ◄/► to select the “OK”, then press the ENTER button.
Be careful to not disconnect the power or remove the USB drive while upgrades are being applied. The TV will turn off and turn on automatically after completing the firmware upgrade. Check the firmware version after the upgrades are complete. When software is upgraded, video and audio settings you have made will return to their default (factory) settings.
Write down your settings so that you can easily reset them after the upgrade; or TV’s firmware in the future. Upgrades will be possible by connecting a USB drive to the USB port located on your TV.
> Press the MENU button to display the menu. Press the ▲/▼ button to select “Support”, then press the ENTER button.
> Press the ▲/▼ button to select “SW Upgrade”, then press the ENTER button. The message “Scanning for USB. It may take up to 30 seconds.” is displayed.
> The message “Upgrade version XXXX to version XXXX?
The system will be reset after upgrade.” is displayed.
> Press the ◄/► to select the “OK”, then press the ENTER button.
Be careful to not disconnect the power or remove the USB drive while upgrades are being applied. The TV will turn off and turn on automatically after completing the firmware upgrade. Check the firmware version after the upgrades are complete. When software is upgraded, video and audio settings you have made will return to their default (factory) settings.
Write down your settings so that you can easily reset them after the upgrade; or TV’s firmware in the future. Upgrades will be possible by connecting a USB drive to the USB port located on your TV.
CLICK ON THE PICTURES TO MAGNIFY
