SONY
26inch 32inch and 37inch LCD TV – Power Supply Circuit Diagram – LED BLINKING
CODES
LED BLINKING CODES
The identification of errors within the SE2AG chassis is
triggered in one of two ways :-
1: Busy or
2: Device failure to respond to IIC.
In the event of one of these situations arising the software will first try to
release the bus if busy (Failure to do so will report with a continuous
flashing LED) and then communicate with each device in turn to establish if a
device is faulty. If a device is found to be faulty the relevant device number
will be displayed through the LED (Series of flashes which must be counted).
SERVICE MODE – ADJUSTMENTS
Service adjustments to this model can be performed using the
supplied remote commander RM-ED009.
Turn on the power to the TV set and enter into the stand-by
mode.
Press the following sequence of buttons on the remote commander.
Press the following sequence of buttons on the remote commander.
INFO+ > 5 > Volume+ > Power
‘TT—’ will appear in the upper right corner of the screen.
Other status information will also be displayed.
Other status information will also be displayed.
Press ‘MENU’ on the remote commander to obtain the following
menu on the screen.
Move to the corresponding adjustment item using the up or down
arrow buttons on the Remote Commander.
Press the right arrow button to enter into the required menu item.
Press the ‘Menu’ button on the Remote Commander to quit the Service Mode when all adjustments have been completed.
Press the right arrow button to enter into the required menu item.
Press the ‘Menu’ button on the Remote Commander to quit the Service Mode when all adjustments have been completed.
[After carrying out the service adjustments, to prevent the
customer accessing the ‘Service Menu’ switch the TV set OFF and then ON again.]
DEFAULT DATA VALUES
TT mode is available by setting the TV for operation in Service
Mode , OSD ‘TT’ appears. The functions described below
are available by selecting the two numbers. To release the ‘Test mode 2’, press
00, 10, 20 ... twice or switch the TV set into Stand-by mode. In ‘TT Menu’
mode, it is possible to remove the Menu from the screen by pressing the Speaker
Off button once. Pressing the Speaker OFF button a second time will cause the
Menu to reappear. The function is kept even when the menu is not displayed on
screen.
KEY
1. Panel size configuration. Changed by TT61...TT68.
2. D/A: D is shown when Digital mode is enabled; A is shown when Analogue mode is enabled. Changed by TT53.
3. TT-- Command prompt.
4. ECS/---: ECS enabled/disabled (TT31).
5. CBA/--: CBA is shown when the TV set is in CBA mode (This mode is available from Factory mode TT19). Changed by TT27.
6. Norm/Fact: Normal or Factory mode. Changed by TT19.
7. DDC/---: DDC enabled/disabled. Changed by TT74.
8. 3/2/1/0: 3, 2, 1, or 0 HDMI inputs toggle. Changed by TT73.
9. E/-: E is shown when EDID WP is enabled; - is shown otherwise. Changed by TT33.
10. N/A: Previously used to indicate Monitor, Hotel, or Otrum mode is enabled.
11. C/-: C (Default value) is shown when MSP Auto Carrier Mute function is enabled; - is shown otherwise. Changed by TT57.
12. M/A: M (Default value) is shown when AM sound is demodulated in MSP; A is shown when AFRIC demodulator is used. Changed by TT72.
13. N/A: Previously used to indicate Clk enabled.
14. T/-: T is shown when digital test is enabled; - is shown otherwise. Changed by TT39.
15. W/-: W is shown when watchdog is enabled; - is shown otherwise. Changed by TT54.
16. C/-: C is shown when chip select is enabled; - is shown instead. This mode is only available in factory mode. Changed by TT58.
17. V/-: V is shown when visual I2C is enabled; - is shown otherwise. Changed by TT59.
18. D/-: D is shown when audio delay is enabled; - is shown otherwise. Changed by TT55.
19. K/-: K is shown when spread spectrum is enabled; - is shown otherwise. Changed by TT94.
20. B/-: B is shown for BRAVIA models; -is shown otherwise. This mode is only available in factory mode. Changed by TT56.
21. T/-: T is shown if temperature algorithm is enabled; - is shown otherwise. Changed by TT52.
22. L/-: L is shown when HDMI log is enabled; - is shown otherwise. Changed by TT34.
23. X/-: X is shown when teletext is centered (Default value); - is shown otherwise. Changed by TT14.
24. B/-: B is shown when SuperBlack algorithm is enabled; - is shown otherwise. Changed by TT51.
25. D/-: D is shown when Panel detection is enabled; - is shown otherwise. Changed by TT21.
26. G/-: G is shown when Gamma correction is enabled; - is shown otherwise. Changed by TT36.
2. D/A: D is shown when Digital mode is enabled; A is shown when Analogue mode is enabled. Changed by TT53.
3. TT-- Command prompt.
4. ECS/---: ECS enabled/disabled (TT31).
5. CBA/--: CBA is shown when the TV set is in CBA mode (This mode is available from Factory mode TT19). Changed by TT27.
6. Norm/Fact: Normal or Factory mode. Changed by TT19.
7. DDC/---: DDC enabled/disabled. Changed by TT74.
8. 3/2/1/0: 3, 2, 1, or 0 HDMI inputs toggle. Changed by TT73.
9. E/-: E is shown when EDID WP is enabled; - is shown otherwise. Changed by TT33.
10. N/A: Previously used to indicate Monitor, Hotel, or Otrum mode is enabled.
11. C/-: C (Default value) is shown when MSP Auto Carrier Mute function is enabled; - is shown otherwise. Changed by TT57.
12. M/A: M (Default value) is shown when AM sound is demodulated in MSP; A is shown when AFRIC demodulator is used. Changed by TT72.
13. N/A: Previously used to indicate Clk enabled.
14. T/-: T is shown when digital test is enabled; - is shown otherwise. Changed by TT39.
15. W/-: W is shown when watchdog is enabled; - is shown otherwise. Changed by TT54.
16. C/-: C is shown when chip select is enabled; - is shown instead. This mode is only available in factory mode. Changed by TT58.
17. V/-: V is shown when visual I2C is enabled; - is shown otherwise. Changed by TT59.
18. D/-: D is shown when audio delay is enabled; - is shown otherwise. Changed by TT55.
19. K/-: K is shown when spread spectrum is enabled; - is shown otherwise. Changed by TT94.
20. B/-: B is shown for BRAVIA models; -is shown otherwise. This mode is only available in factory mode. Changed by TT56.
21. T/-: T is shown if temperature algorithm is enabled; - is shown otherwise. Changed by TT52.
22. L/-: L is shown when HDMI log is enabled; - is shown otherwise. Changed by TT34.
23. X/-: X is shown when teletext is centered (Default value); - is shown otherwise. Changed by TT14.
24. B/-: B is shown when SuperBlack algorithm is enabled; - is shown otherwise. Changed by TT51.
25. D/-: D is shown when Panel detection is enabled; - is shown otherwise. Changed by TT21.
26. G/-: G is shown when Gamma correction is enabled; - is shown otherwise. Changed by TT36.
SMPS SCHEMATICS [37 inch]
SMPS SCHEMATIC [26 & 32 inch]