- The headlamps are controlled by the multi-function lever located on the left side of the steering column. They will come on with the ignition switch in any position. Turning the headlamp switch to the first position turns on the parking lamps, the license plate lamps and the instrument panel illumination. Turning the switch to the second position turns on all of the previous lamps and the headlamps. Turning the switch to the off position turns off all the lamps.
- Turning the lighting switch to the first position can turn on the parking lamps. Turning the switch to the OFF position can turn off the parking lamps. This lever also controls headlamp high beam and low beam. When the headlamps are on, pushing the lever away from the driver until the switch clicks changes the lamp from low beam to high beam. An indicator lamp on the instrument cluster assembly will come on when the high beam headlamps are on. To return the headlamps to low beam, pull the lever toward the driver.
- The headlamps must be aimed for proper illumination of the road. Headlamp aim should be checked whenever a new headlamp assembly is installed or service repairs to the front-end area may have disturbed the headlamp assembly or its mountings.
DIAGNOSTIC INFORMATION AND PROCEDURES [HEAD LAMPS] {Click on table to Magnify}
REPAIR INSTRUCTION ON-VEHICLE SERVICE [HEAD LAMPS]
Removal Procedure- Support the hood suitably.
- Disconnect the negative battery cable.
- Remove the front bumper spacer.
- Remove the bolts (1).
- Remove the front bumper spacer from the bumper fasia (2).
- Remove the bolts and washer (1).
- Disconnect the electrical connectors.
- Remove the headlamp (2) .
INSTALLATION
- Install the headlamp with the bolts.
- Connect the headlamp connector and parking lamp connector.
- Install the front bumper spacer with the bolts.
- Connect the negative battery cable.
SIGNAL LAMPS & HAZARD LAMPS
Removal Procedure
- Disconnect the negative battery cable.
- Remove the front bumper spacer. Refer to Section 9M, Exterior Trim.
- Remove the turn signal lamps from the front bumper spacer.
- Disconnect the electrical connector (1).
- Remove the screw (2).
- Remove the turn signal lamp assembly (3).
- Connect the electrical connector.
- Install the turn signal lamp assembly with the screw.
- Install the front bumper spacer. Refer to Section 9M, Exterior Trim.
- Connect the negative battery cable.
SIDE TURN SIGNAL LAMPS
Removal Procedure
- Disconnect the negative battery cable.
- Slide the side turn signal lamp rearward.
- Remove the lamp.
- Disconnect the electrical connector.
- Connect the electrical connector.
- Install the side turn signal lamp.
- Connect the negative battery cable.
STOP LAMPS & INTERIOR COURTESY LAMPS
TAIL LAMPS ASS'Y
- Removal Procedure
- Disconnect the negative battery cable.
- Open the tailgate.
- Remove the luggage compartment wheelhouse trim.
- Disconnect the electrical connector.
Remove the tail lamp assembly.
- Remove the screws (1).
- Remove the tail lamp (2).
- Install the tail lamp assembly with the screws.
- Connect the electrical connector.
- Install the luggage compartment wheelhouse trim.
- Connect the negative battery cable.
REAR FOG LAMP
The rear fog lamp will not operate unless the
headlamps are ON. If the headlamps are not operating, repair that problem
before attempting to diagnose the rear fog lamp.
FRONT FOG LAMP
Removal Procedure- Disconnect the negative battery cable.
- Raise and suitably support the vehicle.
- Remove the front wheels.
- Remove the front wheel house splash shield.
a. Bolt and clips.
Remove the wheelhouse splash shield.
b. Splash shield.
Remove the front fog lamp.
- Remove the screws (1).
- Disconnect the electrical connector (2).
- Remove the front fog lamp (3).
- Install the front fog lamp with the screws.
- Connect the front fog lamp connector.
- Install the front wheelhouse splash shields with the clips and the bolts.
- Install the front wheels.
- Lower the vehicle.
- Connect the negative battery cable.
REAR FOG/BACKUP LAMPS
Removal Procedure- Disconnect the negative battery cable.
- Remove the tail lamp assembly. Refer to “Tail lamps Assembly “in this section.
- Remove the bulb(s).
- Install the bulb(s).
- Install the tail lamp assembly. Refer to “Tail lamps Assembly “in this section.
- Connect the negative battery cable.
