Thursday, May 23, 2013

TATUNG V27CMTT-Exx - V30CMTT-Exx - TROUBLESHOOTING - REPAIR FLOW CHART - CHILD LOCK RELEASE



TATUNG 27”/ 30” Wide Screen European LCD Multi-Media Display.
FAULT CODES


NP1
No Picture and No Sound
in TV mode
•  Make sure the Power cord and Aerial Cable are
properly connected .
•  Make sure the batteries in remote control are not flat.
•  Press the POWERbutton to switch the TV on.
•  Switch to TV source by pressing “TV” button.
•  Run “Automatic Search ” by operating the remote
control

NP2
No Picture and No Sound
in video mode.
•  Check the connection between the optional video
equipment and the TV.
•  PressSCART , Video/S-V orCOMPONENTbutton
on the remote control to select the right video
equipment.

NP3
TV is automatically turned
off
•  Check if the “SLEEP” timer is activated .
•  Press the POWERbutton to turn on the TV once
again

PP1
Double Images /Ghosts
If the TV suffers interference from signals reflecting from
mountains or buildings , double-pictures or Ghosts will
occur.
•  Adjust the aerial’s location and direction
•  Replace it with one with better directionality.
•  Turn off or disconnect the booster if it is in use , as
the booster may be inappropriate

PP2
Snowy picture and noisy
Sound
If snow totally blocks out the picture , there may be a
problem with the Aerial or Aerial Cable .
•  Have the TV and aerial been connected properly ?
Has the aerial cable been damaged ?
•  Is the aerial pointing in the right direction ?
•  Is the aerial itself faulty ?
•  Try using a booster , as signal transmission may be
low

PP3
Distorted picture and
noisy sound
•  Turn off or disconnected the booster if it is in use , as
broadcast signals may be too strong

PP4
Dotted Lines / Stripes
in the picture
If the TV or aerial suffers interference from other
equipment , stripes or noise may appear in the picture.
•  Keep the TV away from noise sources such as
personal computer , amplifier , cars, motorcycles or
hair-dryers.
•  If the aerial suffers interference from a radio tower or
high-voltage wire , contact the local dealer.

PP5
Stripe noise .
•  Check the coaxial cable connected with the TV is not
oxidized
•  Do not use 300 ohm twin lead cables as interference
may occur
•  It is recommended to use a 75 ohm coaxial cable (not
supplied) to get premium quality picture.
•  Keep the aerial cable away from other connecting
cables

PP6
No color, too light or too
dark
•  Adjust the picture settings -  APC, Brightness,
Contrast, Saturation , Color Temp.
•  Press “RESET ” button on remote control

NS1
Good picture, no sound
•  Make sure the headphone is not connected.
•  Check audio connections between Equipment &
LCD-TV.
•  PressMUTEor VOL+ to cancel the muting.

NS2

•  Make sure that the aerial connected is 75 ohm coaxial
cable (not supplied) , not 300 ohm twin lead cables .
•  Keep the aerial cable away from other connecting
cables.
•  Press SOUNDto select “Mono” which will reduce
the noise.
•  Adjust BASSor TREBLEproperly in OSD.

NS3
No sound in TV mode
If the Country setting for the TV is incorrect , it may
prevent the sound from being issued
•  Select the Countrywhere you are located in OSD
Menu.
•  If the country is not listed in OSD , select “Other Country”.

NS4
Good picture, but noisy
sound or no sound in TV
mode.
•  If the sound of “all the channels” is noisy , run
A.P.S. again by selecting Automatic Searchin OSD.
•  If the sound of “some channels” is noisy or no
sound , select Manual Search and select an
appropriate TV systemin OSD such as B/G , D/K ,
I , L/L’ ; then , store it.
( If the sound system setting for a TV channel is
incorrect , it may prevent the sound from being issued .)

PC1
PC display is Not Full
Screen
•  Select Auto Image Adjustin OSD menu to optimize
the image .
•  If executing Auto Image Adjust still can not achieve
full screen display, adjust V.Position and H.Position
in PC mode

PC2
Horizontal Noise or Color
pattern is not uniform
•  Select Auto Image Adjust in OSD menu to optimize
the image .
•  If still no good , adjust H. Phase in OSD menu

PC3
“Out of Range” message
•  Maximum PC resolution supported is 1024x768 /
1280 x 768, so the screen will appear “Out of range”
at higher resolution.
•  Reduce the resolution to 1024x 768/ 1280x 768 from
PC .

PC4
No Sound
•  Make sure PC audio Input is well connected.

PC5
“Not Available” message
on PIP
•  If Main-Display is PC and Sub-display is
Component , resolution of the PC should be reduced
to 800 x 600 or lower ;then , the PIP will work well.

PC6
After“No Signal ”has
appeared on PC mode for a
while, the view disappears
and the “ LED Indicator”
turns from Green
to”Red”.
•  Press any key on keyboard or move the mouse to
activate the PC , because the PC may go to power
saving status.
•  Check if the D-sub connector (Cable) is disconnected or loose .

RC1
Remote Control does not
work
•  Make sure the batteries in remote control are not flat
•  Check the polarity of the batteries
•  Use the remote control in the front of the TV or from
less than seven meters away.
•  make sure the Remote Sensor Window is not under
strong lighting

RC2
Can not change channels
with the remote control
•  Press TV button to switch to TV mode.
•  Make sure the TV is not in Teletext mode

PH1
Picture suddenly Stops
Responding or abnormal
•  Press RESETbutton on remote control .
•  Unplug and then plug the Power Cord of the TV
from the AC outlet (or the Adapter from the TV).
•  If the picture still no good , execute “Initial
EEPROM”.
Press POWERkey to turn off the TV . Press“CH DN” key
on the top of LCD TV ( don’t release ) ; then, press
POWER button on remote control until “Initial
EEPROM” appears on the screen .
(Note: Remind user that every setting will be return to
factory preset mode including Child Lock , PIN No. ,
Programs)



TROUBLESHOOTING FLOW CHART [Clcik on images to Enlarge]
Power Start Not Good
NO BACK-LIGHT, BUT LED LIGHTS UP
NO PICTURE, BUT BACK-LIGHT & LED LIGHTS UP
PICTURE ABNORMAL OR HALT

Steps to Refresh EEPROM
  • Press POWER key to turn off the LCD-TV.
  • Press CH. Down key on the top of LCD-TV (don’t release) and then press POWER button on remote control, until “EEPROM Initial” appears.
  • Now, all the buttons, which you are pressing, could be loosed.

If the PIN of Child-Lock is forgotten , the only way to unlock the channels is to refresh EEPROM and the PIN will also recover initial number “1111”. Besides , all the STORE done by user will be refreshed to the situation of First Time Installation.
FRAME DEFECTS OR STRIPED LINES AT ALL SOURCES