TOSHIBA - SATELLITE PRO 6100 SERIES _ Service Help _ Contn:

Contn:
                                                               [2]

WIRELESS LAN CARD REMOVAL

• Remove one M2x4 black screw securing the mini PCI cover and lift out the cover.
• Disconnect the black and white coax from the wireless LAN card.
• Spread the Mini-PCI connector clips and pull the Wireless LAN card out of the connector about 45 degree angle.

TOP COVER REMOVAL

• Turn the computer upside down and remove the following screws:

1. 12 M2.5x8 black screws

• 1 M2.5x4 black flat head screw
• 2 M2.5x20 black screws.
• Turn the computer right side up with the rear facing you.
• Remove two M2.5x4 black flat head screws securing the top cover.

• Disconnect the left speaker cable from PJ310 and the right speaker cable from PJ311 on the top board.
• Disconnect the LCD/FL harness from PJ5002/5001 and the IPS membrane switch from PJ122 on the video board.
• Lift out the top cover assembly.
• When re- installing the top cover, ensure that the bluetooth coaxial cable is properly routed to the Bluetooth slot

VIDEO BOARD REMOVAL

• Remove three 2x4 brass screws securing the video board.
• Disconnect the video board from PJ100 on the system board.

COOLING MODULE REMOVAL

• Disconnect the fan cable from PJ8770 on the top board.
• Remove two M2.5x6 black flat head screws and four M2x4 brass screws securing the cooling module.
• Lift out the cooling module.

CPU REMOVAL

• Disconnect the fan cable from PJ8770 on the top board.
• Remove two M2.5x6 black flat head screws and four M2x4 brass screws securing the cooling module.
• Lift out the cooling module.
• When installing the CPU, make sure that a silicone grease is applied before attaching the heat sink.  

RTC BATTERY REMOVAL

• Disconnect the RTC harness from PJ5 on the Battery/LED board.
• Lift out the RTC battery.

POWER SUPPLY BOARD REMOVAL

• Disconnect the power supply harness from PJ850 and PJ851 on the system board.
• Remove two M2.5x4 black flat head screws securing the power supply board.
• Disconnect the power supply board from the system board.

SD/SOUND BOARD REMOVAL

• Disconnect the sound interface cable from PJ103 and the SD interface cable from PJ150 on the SD/Sound board.
• Remove one M2.5x4 black flat head screw securing the SD/Sound board.
• Remove the wireless LAN switch button.
• Lift out the SD/Sound board.

SYSTEM BOARD REMOVAL

• Remove one M2.5x6 black flat head screw securing the HDD guide assembly and lift out the HDD guide assembly.
• Remove three M2.5x6 black flat head screws securingthe select bay cover and lift out the select bay cover.
• Disconnect following cables from the system board:

1. Sound interface cable from PJ302
2. SD interface cable from PJ365
3. DC-IN jack harness from PJ8800

• Remove four M2.5x4 black flat head screws securing the system board.
• Lift out the system board.
• Remove the video chip heat sink plate assembly from the system board.
• When re-installing the heat sink plate assembly, make sure that a 0.2g silicone grease is applied to the video controller IC(IC11).

MEMBRANE SWITCH REMOVAL

• Remove three M2.5x4 black flat head screws securing the membrane switch.
• Lift out the membrane switch assembly.

SPEAKERS REMOVAL

• Remove two M2.5x4 black flat head screws securing the left and right speakers.
• Turn the display assembly right side up and open the LCD panel.
• Lift out the left and right speakers.

DISPLAY MASK REMOVAL

• Remove two mask seals at the bottom corners of the display assembly using a pair of fine-tipped tweezers.
• Remove two M2.5x6 black flat head screws securing the display mask.
• There are 23 latches securing the display mask.  Carefully insert your fingers between the mask and the LCD panel and pry open the latches starting from the six top latches, to the five latches on each right and left sides, ending with the bottom seven latches.

FL INVERTER & 14.1" LCD REMOVAL

• Remove one M2x4 silver screw securing the FL inverter board.
• Carefully lift up the FL inverter board and disconnect the LCD/FL cable from CN1 and the FL cable from CN2.
• Remove four mask seals to expose four screws securing the LCD module assembly.
• Remove four M2X5 silver screws securing the LCD module assembly.
• Carefully rotate out the top of the LCD module enough to access the display cable.
• Peel off the tape securing the LCD/FL cable and disconnect the cable.
• Remove four M2x3 silver screws securing the right and left LCD brackets.