Friday, March 08, 2013

PANASONIC VIERA TC-P42S1 - SERVICE MODE - HOTEL MODE - SELF CHECK MODE - PCB EXCHANGE - WHITE BALANCE ADJUSTMENT



TO ENTER SERVICE MODE
  • While pressing [VOLUME ( - )] button of the main unit, press [INFO] button of the remote control three times within 2 seconds.
Key command
[1]  button...Main items Selection in forward direction
[2]  button...Main items Selection in reverse direction
[3]  button...Sub items Selection in forward direction
[4]  button...Sub items Selection in reverse direction
  • Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control to EXIT service mode.
  • [VOL] button...Value of sub items change in forward direction ( + ), in reverse direction ( - ).
SERVICE TOOL MODE
  • Select [SRV-TOOL] in Service Mode.
  •  Press [OK] button on the remote control.
To Display of SOS History
  • SOS History (Number of LED blinking) indication.
  • From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment.
  • This indication except 2nd and 1st occurrence after shipment will be cleared by [Self-check indication and forced to factory shipment setting].
POWER ON TIME/COUNT
Note : To display TIME/COUNT menu, highlight position, then press MUTE for (3sec).
Time : Cumulative power on time, indicated hour : minute by decimal
Count : Number of ON times by decimal
Note : This indication will not be cleared by either of the self-checks or any other command.
To Exit Disconnect the AC cord from wall outlet.
Hotel mode: Purpose. To Restrict a function for hotels.
Access command to the Hotel mode setup menu In order to display the Hotel mode setup menu, enter the following command (within 2 second).
[TV] : Vol. [Down] + [REMOTE] : INPUT (3 times)
To exit the Hotel mode setup menu Disconnect AC power cord from wall outlet.
  • Self-check function to test the unit.
  1. Checking the IIC bus lines
  2. Power LED Blinking timing
To access Self-check indication only:
  • Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [OK] button on the remote control for more than 3 seconds.
Self-check indication and forced to factory shipment setting:
  • Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote control for more than 3 seconds.
  • To Exit: Disconnect the AC cord from wall outlet.
Adjustments
  • Adjust driver section voltages referring the panel data on the panel data label.
  • Check or adjust the following voltages with the multimeter.
Caution
  • First perform Vsus adjustment.
  • The Vscn voltages are measured from the Vad (Vad_base), but may be measured from the GND (GND_base) in an unavoidable case.
Item / Preparation
  1. Input a white signal to plasma video input.
  2. Set the picture controls as follows.
  • Picture menu: Vivid
  • Normal: Set
  • Aspect: Full
Name
Test Point
Voltage
Volume

Vsus
TPVSUS (SS)
Vsus ± 2V
VR251(P)
Ve
TPVE (SS)
Ve ± 2.5V
Fixed
Vset
TPVSET (SC)
290V ± 9V
Fixed
Vad
TPVAD (SC)
- 195V ± 2V
VR16600 (SC)

Vscn
TPVSCN (SC)
Vad_base : 148V ± 1V
GND_base : - 47V ± 3V

VR16841
(SC)
Vda
TP9 (P)
60V + 1V, - 2V
Fixed
See the Panel label.

P.C.B. (Printed Circuit Board) exchange
Caution: To remove P.C.B., wait 1 minute after power was off for discharge from electrolysis capacitors.
Quick adjustment after P.C.B. exchange: Adjust the following voltages with the multimeter.

P.C.B.
Name
Test Point
Voltage
Volume

P Board
Vsus
TPVSUS (SS)
Vsus ± 2V
VR251 (P)
SC Board
Vad
TPVAD (SC)
- 195V ± 2V
VR16600 (SC)

SC Board

Vscn

TPVSCN (SC)
Vad_base : 148V ± 1V
GND_base : - 47V ± 3V

VR16841 (SC)

A Board

White balance and Sub brightness for NTSC, PAL, HD, PC and 625i signals


See the Panel label. Caution:  Absolutely do not reduce Vsus below Ve not to damage the P.C.B.
WHITE BALANCE ADJUSTMENT
  • Make sure the front panel to be used on the final set is fitted.
  • Make sure a color signal is not being shown before adjustment.
  • Put the color analyzer where there is little color variation.
  • Set the Picture menu to [vivid] and output the W/B pattern.

  • Check that the color temperature is [Cool].
  • Set to serviceman mode, WB-ADJ.
  • Set [R-CUT] [G-CUT] [B-CUT] the values written in table 1.
  • Attach the sensor of color analyzer to the center of highlight window.
  • Fix G drive at C0h and adjust [B-DRV] and [R-DRV] so x, y value of color analyzer become the [Color temperature High] in table.
  • Increase RGB together so the maximum drive value in RGB becomes FC. That is, set [ALL DRIVE] to FC.  Execute adjustment again. When that, the maximum value of R/G/B DRV should be FC, and either R/G/B DRV should be FC.
  • Set color temperature to [Normal].
  • Set [R-CUT] [G-CUT] [B-CUT] the values written in table 1.
  • Attach the sensor of color analyzer to the center of highlight window.
  • Fix G drive at C0h and adjust [B-DRV] and [R-DRV] so x, y value of color analyzer become the [Color temperature Mid] in table.
  • Increase RGB together so the maximum drive value in RGB becomes FC. That is, set [ALL DRIVE] to FC.  Execute adjustment again. When that, the maximum value of R/G/B DRV should be FC, and either R/G/B DRV should be FC.
  • Set color temperature to [Warm].
  • Set [R-CUT] [G-CUT] [B-CUT] the values written in table 1.
  • Attach the sensor of color analyzer to the center of highlight window.
  • Fix G drive at C0h and adjust [B-DRV] and [R-DRV] so x, y value of color analyzer become the [Color temperature Low] in table.
  • Increase RGB together so the maximum drive value in RGB becomes FC. That is, set [ALL DRIVE] to FC. Execute adjustment again. When that, the maximum value of R/G/B DRV should be FC, and either R/G/B DRV should be FC.
  • Set color temperature to [Cool].
                                                            Click on the image to enlarge