GENERAL SETUP PROCEEDINGS
1.
Power on the DIRECTV Receiver.
2.
On the DIRECTV Universal Remote Control, press SAT once. Press and hold
Setupuntil the SATkey blinks twice,
then release Setup.
3.
Use theSetup Codes for DIRECTV Receivers or DVRs (on the next two pages) to
locate the brand name and code for your specific DIRECTV receiver. Then use the
keypad to enter the four-digit code. If performed correctly, the SATkey will
blink twice.
NOTE:
If the SATkey emits a long blink, the code is invalid. Repeat steps 2 and 3 and
try entering the same code again.
4.
Aim the DIRECTV Universal Remote Control at the DIRECTV Receiver and press
Power once. The DIRECTV Receiver should
turn off. If it does not, repeat steps 3 and 4, trying each code for your brand
until you find one that works. If it still does not work, try Searching For
Your Code.
Hughes
Network Systems (most models) à 0749
Hughes
Network Systems models GAEB0, GAEB0A, à 1749
GCEB0,
GCEB0A, HBH-SA, and HAH-SA GE models GRD33G2A and GRD33G3A à 0566
GE
model GRD122GW à 0866
Hitachi
model HDS210R à 0819
Mitsubishi
HD models SRHD400 and SRHD500 à 0749
Panansonic
models TZ-DBS01 and TZ-DRD100 à 0247
Panasonic
models TUIRD10 and TUIRD20 à 0701
Philips
models DSX5150R, DSX5250R/I, DSX5350R, DSX5353R, DSX5353X, and DSX5375R à 1076
Philips
models DSX5500 and DSX5400 à 0099
Philips
HD model DSHD800R à 0749
Proscan
model PRD8630A à 0566
Proscan
model PRD8650B à 0766
RCA
models DRD102RW and DRD203RW à 0866
RCA
models DRD301RA, DRD302RA, DRD303RA, DRD403RA, and DRD703RA à 0566
RCA
models DRD502RB, DRD503RB, DRD505RB, DRD515RB, DRD523RB, and DRD705RB à 0766
RCA
models DRD202RD, DRD221RD, DRD222RD, 0392 DRD223RD, DRD225RD, DRD420RE,
DRD440RE, DRD460RE, DRD480RE, DRD430RG, DRD431RG, DRD450RG, DRD451RG, DRD485RG, RD486RG, DRD430RGA, DRD450RGA, DRD485RGA,
DRD435RH, DRD455RH, and DRD486RH RCA model DTC-100 à 0492
Samsung
model SIR-S60W à1109
Samsung
model TS-160 à1256
Samsung
models SIR-S70, SIR-S75, and SIR-S300W, à1309
Sony
models SAT-A1 and SAT-B1 à 0639
Sony
models SAT-A2 and SAT-B2 à 0739
Sony
models SAT-A3, SAT B3, SAT-A4, and SAT-B4 à 0839
Sony
models SAT-A50, SAT-A55, SAT-B50, SAT-B55, and SAT-HD100 à 0939
Sony
models SAT-A65, SAT-A65A, and SAT-B65A à 1039
Toshiba
model DST-3000 à1749
Uniden
model UDS100 à 0724
Zenith model DTV1080 à1856
SETUP CODE FOR DIRECTTv DVRs
Hughes
Net. Sys./TiVo à1142 (program under DIRECTV
mode) model GXCEBOT
Philips/TiVo
à1142 (program under DIRECTV mode) model
DSR6000R
RCA
UltimateTV à1492 (program under DIRECTV
mode) model DWD490RE
Sony/TiVo
à1639 (program under DIRECTV mode) model
SAT-T60
Sony
UltimateTV à 1739 (program under DIRECTV
mode)
PROGRAMMING
OTHER DEVICE CONTROL
The
DIRECTV Universal Remote Control is also preprogrammed to operate an RCA TV, an
RCA VCR, and a Pioneer audio receiver. To control devices other than the
default brands, perform the following steps; otherwise skip this section:
NOTE:
To control a DVD/DVR player, program the VCRkey. For TV/VCR Combo control, skip this section.
1.
Turn on a device and, if applicable, insert a video cassette or DVD. [NOTE:
Please read steps 2 through 4 completely before proceeding. Highlight or write
down the codes and device you wish to program before moving on to step 2.]
2.
On the DIRECTV Universal Remote Control, press the device key you wish to
program once (e.g.,TV,VCR,or AUX). Press and hold Setup until the selected
device key blinks twice and then release Setup.
3.
Use the Manufacturer’s Codes to locate the four-digit number corresponding to
the brand name of the device you want to control. Enter the first four-digit
code
for your device. If performed correctly, the light under the select device key
will blink twice. [NOTE: If the selected device key emits a long blink, the
code is invalid. Repeat steps 2 through 3 and try entering the same code again.
4.
Aim the DIRECTV Universal Remote Control at the device and press Power once.
The device should turn off. If it does not, repeat steps 2 and 3, trying each
code for your brand until you find one that works. If it still does not work,
try Searching For Your Code. [NOTE: If
the device does not have a Power key, press
the
(Play) key.]
5. Repeat steps 1 through 4 for each device you
want the the DIRECTV Universal Remote Control to control. For future reference,
write down each working device code.
PROGRAMMING
TV/VCR COMBO CONTROL
If
you own a TV/VCR Combo, perform the following instructions to control this
device:
1.
Turn on your TV/VCR Combo and insert a video cassette.
2.
On the DIRECTV Universal Remote Control, press VCR once. Press and hold Setup
until the VCR key blinks twice, then release Setup.
3.
Use the Setup Codes For TV/VCR Combos to locate the brand name and then enter
the first four-digit code for your TV/VCR Combo. If you perform this procedure
correctly, the VCR key will blink twice. [NOTE: If the VCRkey did not blink
twice after enter-ing the code’s last digit, then repeat steps 2 through 3
and
try entering the same code again.]
4.
Aim the DIRECTV Universal Remote Control at your TV/VCR Combo and press Power
once. The unit should turn off. If it
does not respond, repeat steps 2 and 3, trying each code listed for your brand
until you find one that works. If it still does not work, try Searching For
Your Code.
5.
If you’ve located a TV/VCR setup code that works your TV/VCR Combo and a
separate TV code is also listed, you’ll need to program this code into the
DIRECTV Universal Remote Control to access volume control. If there is no separate TV code listed, you
will need to perform the following steps to access
volume
control:
a.
Press and hold Setup until the VCRkey
blinks twice, then release Setup.
b.
Enter 9 - 9 - 3.The VCRkey will blink twice.
c.
Press VCRonce. The VCRkey will blink
twice.
6.
For future reference, write down each working device code.
SEARCHING
FOR YOUR CODE
If
your TV, VCR, DIRECTV Receiver, or auxiliary device does not respond to the
DIRECTV Universal Remote Control after trying all of the codes listed for your
brand, or if your brand is not listed at all, try searching for your code.
For
example, to search for a code for your TV:
1.
Turn on your TV.
2.
On the DIRECTV Universal Remote Control, press TV once. Then press and hold
Setup until the TV key blinks twice, then release Setup.
3.
Enter 9- 9 - 1.The TVkey will blink twice.
4.
Aim the remote control at the TV and slowly alternate between pressing Power
and TV. Stop when the TV turns off.
NOTE:
In the search mode, the DIRECTV Universal Remote Control will send IR codes
from its library to the selected device, starting with the most popular
code
first.
5.
Press Setup once to lock in the code.
6. To search for the codes of your other
devices, repeat steps 1 through 5, but substitute the appropriate key
(i.e.,VCR,AUX,or SAT) for the device you are searching for.
CHECKING
THE CODES
If
you have set up the DIRECTV Universal Remote
Control
using the Searching For Your Code procedure, you may need to find out which
four-digit code is operating your equipment. For example, to
find
out which code is operating your TV:
1.
Turn on your TV.
2.
On the DIRECTV Universal Remote Control, press TV once. Then press and hold
Setup until the TVkey blinks twice, then release Setup.
3.
Enter 9- 9 - 0.
4.
To view the code for the first digit, press 1once. Wait 3 seconds and count the number of LED blinks (e.g., 3 blinks
= 3) and write down the number in the leftmost TV Code box. [NOTE: If a code
digit is “0”, the LED will not blink.]
5.
Repeat step 4 three more times for remaining digits. Use 2for the second digit,
3for the third digit, and 4for the fourth digit. Finish writing down the code.
6. To check for other device codes, repeat steps
1 to 5, but substitute the appropriate key (i.e.,VCR, AUX,or SAT) for the
device you are checking. Write down the
code.