Wednesday, March 20, 2013

DISH NETWORK -EZ REMOTE CONTROL - SETUP PROCEDURE




CONNECTING THE SATELLITE RECEIVER & TV
  • Connect a coaxial cable between the TV Set Out on the satellite receiver and the tuner input on the TV
Note: If you connect your TV a different way (for example, using yellow, red, and white audio/video RCA-type or S-Video cables), the feature to switch your TV to satellite programming using will not work.
Set [ 4 – 3 ] channel on the back of the receiver toCH3.  [Note: If you prefer Channel 4, instructions are provided later to change this setting.   If your satellite receiver does not have a [ 4 – 3 ] channel, see your satellite receiver’s User’s Guide for how to set TV Set Out on the satellite receiver to Channel 3.

SETTING UP THE REMOTE TO CONTROL YOUR TV
1. Find the brand name of your TV in the TV code tables. [refer previous post here] 2. Turn on your TV.
3. Press and hold [Antenna button] until both [sat & tv button] lights turn on (it takes about five seconds).
4. Release . [Antenna & TV] light will flash.
5. Press [TV]. Notice [TV] light turns on and stays on.
6. Enter one of the three-digit codes for your TV from the TV code tables while [TV] light is on.  [Note: You have about 20 seconds to begin entering the TV code.]
7. Press the MUTE button and watch [TV] light.  If [TV] light flashes three times, the code is valid and you can go to step 8. If [TV] light does not flash at all, the code may not have been entered correctly. So, start over from step 3 and try the code again.
8. Press [TV] and your TV should shut off. If your TV shuts off, go to step 9. If not, pick another code for your TV brand from the TV Codes table and go back to step 3. If you have tried all of the codes and none work, go to How to Scan for TV and VCR.
9. Turn your TV back on by pressing [TV] again and try the other buttons below to make sure they work. ( Press the 0 through 9 buttons to change channels on your TV.)
Press [Ch Up] and Ch Dn] to change channels on your TV.
Press to change the TV volume.  If [Vol+/Vol -] buttons work, go on to the next section to set up . If not, pick another code for your TV brand from the TV Codes table
step 3.
1. Make sure your TV and satellite receiver are connected and your remote control is set up to control your TV using the instructions in the last two sections.
2. Turn on your TV and tune to a channel other than 3 (for example, 4 or 5).
3. Press and your satellite receiver should turn on and your TV should tune to Channel 3.
4. Press theMENUbutton. If you see the satellite receiver Menu screen, gotostep5. If not, go to step 15.
5. If you want to keep your satellite programming on TV Channel 3, check the box below and go to step 28.
6. If you prefer to have your satellite programming on TV Channel 4,go onto step7. VOL
7. Set the switch on the back of the satellite receiver toCH4. The TV will lose the picture from the satellite receiver, but this is OK.
Note: If your satellite receiver does not have a switch, see your satellite receiver’s User’s Guide for how to set TV Set Out on the satellite receiver to channel 4.
8. Press and hold until both lights turn on (it takes about five seconds).
9. Release . light will flash.
10.Enter0-4.
11. Press MUTE while watching light.
12. light will flash three times.  If the light does not flash at all, repeat this procedure starting with step 8.
13.Press while watching your TV. If your TV tunes to Channel 4, go to step 14. If not, go to step 7.
14.Press the MENU button. If you see the satellite receiver Menu screen, check the box below and go to step 28.

 TO CONTROL YOUR TV
1. Find the brand name of your TV in the TV code tables. [refer previous post here] 2. Turn on your TV.
3. Press and hold [Antenna button] until both [sat & tv button] lights turn on (it takes about five seconds).
4. Release . [Antenna & TV] light will flash.
5. Press [TV]. Notice [TV] light turns on and stays on.
6. Enter one of the three-digit codes for your TV from the TV code tables while [TV] light is on.  [Note: You have about 20 seconds to begin entering the TV code.]
7. Press the MUTE button and watch [TV] light.  If [TV] light flashes three times, the code is valid and you can go to step 8. If [TV] light does not flash at all, the code may not have been entered correctly. So, start over from step 3 and try the code again.
8. Press [TV] and your TV should shut off. If your TV shuts off, go to step 9. If not, pick another code for your TV brand from the TV Codes table and go back to step 3. If you have tried all of the codes and none work, go to How to Scan for TV and VCR.
9. Turn your TV back on by pressing [TV] again and try the other buttons below to make sure they work. ( Press the 0 through 9 buttons to change channels on your TV.)
Press [Ch Up] and Ch Dn] to change channels on your TV.
Press to change the TV volume.  If [Vol+/Vol -] buttons work, go on to the next section to set up . If not, pick another code for your TV brand from the TV Codes table
step 3.
1. Make sure your TV and satellite receiver are connected and your remote control is set up to control your TV using the instructions in the last two sections.
2. Turn on your TV and tune to a channel other than 3 (for example, 4 or 5).
3. Press and your satellite receiver should turn on and your TV should tune to Channel 3.
4. Press theMENUbutton. If you see the satellite receiver Menu screen, gotostep5. If not, go to step 15.
5. If you want to keep your satellite programming on TV Channel 3, check the box below and go to step 28.
6. If you prefer to have your satellite programming on TV Channel 4,go onto step7. VOL
7. Set the switch on the back of the satellite receiver toCH4. The TV will lose the picture from the satellite receiver, but this is OK.
Note: If your satellite receiver does not have a switch, see your satellite receiver’s User’s Guide for how to set TV Set Out on the satellite receiver to channel 4.
8. Press and hold until both lights turn on (it takes about five seconds).
9. Release . light will flash.
10.Enter0-4.
11. Press MUTE while watching light.
12. light will flash three times.  If the light does not flash at all, repeat this procedure starting with step 8.
13.Press while watching your TV. If your TV tunes to Channel 4, go to step 14. If not, go to step 7.
14.Press the MENU button. If you see the satellite receiver Menu screen, check the box below and go to step 28.