PANASONIC - TY-TP42P10S _ TY-TP50P10S _25-POINT CALIBRATION

25 POINT ADJUSTMENTS

Prepare setting for adjusting PC

• Create folder and copy files listed below for Excel data processing.
• Create a folder directly onto the C Drive. C:/25PDATA
• Copy the files and create the data folder listed below into the "25PDATA" folder.
• 25P Adjustment Data Procssing.xls
• Grid.exe
• grid.ini
• import.prm
• data folder (C:\25DATA\data)
• Adjustment processing result will be saved in the data folder automatically ("S/N" xls).’

Prepare setting of Excel

• Start up the Visual Basic Editor by selecting "Tool" - "Macro" -> "Visual Basic Editor".
• Select "Reference Setting" from "Tool".
• Put a check mark on "SOLVER" in available references.
• If .SOLVER.xla. doesn.t exist or does not show in references, press .reference. to select .SOLVER.xla..SOLVER.xla. should be in C\Program Files\Microsoft Office\Library\Solver.

EXPLANATION OF 25-POINT CALIBRATION

To start performing 25-point Calibration

• Start up .LtabMon S. (Make sure the Touch Driver is not running.)

• Press 'Sampling' Detailed sampling data box will appear.
• Start up 'Grid.exe'

• While touching the cross point in the top left corner with the touch pen, press .Capture (Enter Key).
• Move to right one section and press 'Capture (Enter key)'. Repeat the same procedure to get calibration data from 5 points.
• Move to far left corner in the second row, repeat the same procedure from left to right to get calibration data.  Collect data from all 25 points.
• When you finish with the last point, press .Save.
• Right-click to close 'Grid'
• RES.dat will be saved in 25PDATA folder in C drive.

Excel data processing (Make sure the setting has been prepared before hand.)

• Start up .25P Adjustment Data Procssing.xls. (Macro).
• Select a number for adjusting model.
• 1:50 inch TY-TP50P10S
• 2:42 inch TY-TP42P10S
• 3:58 inch TY-TP58P10S
• 4:65 inch TY-TP65P10S
• Process the aquired data. Press .RES - RES0.  Press .OK. According to the message dialog box.
• Perform the data validation and defrag.  Press 'Validation & Initialization & Defrag'

1. Press 'DATA - Export' to save result of the calibration.
2. The data will be saved as 'importf.prm' in 25PDATA folder.
3. Press 'Exit' to quit.
4. Enter products serial number when asked for S/N.
5. S/N.xls. will be saved in 25PDATA folder.
6. Import the aquired data.
7. Press 'Parameter' in LTabMonS.

• Press 'Load File' to open 'importf.prm' file saved in 25PDATA folder.

• The result will be imported and reflect to each parameter.

• Press 'Write to ROM' to write.
• Exit 'LtabMon' to finish.

PRECISE CALIBRATION

• Make sure the LtabMonS is not running. Start up the 'Touch Driver'
• Press 'precise calibration' from the driver.s setup panel.

• “precise calibration” dialog box will appear.
• Press”OK”.

• Touch the “X” marker in the top right corner (shown in yellow) with the touch pen to stop.
• When the driver capture XY coordinates, the yellow “X” marker moves one to right.
• Capture XY coordinate for each "X" marker shown in yellow.
• Get data from all 25 points.
• When you finish collecting data from all points, the calibration result will be asked.
• Then press ‘OK’ to exit.

CHECK FOR CALIBRATING RESULT [TEST]

• Exit the driver.s setup panel, and touch any marker to test.
• Point positions should not be too far off. It should be whithin 5 mm.
• In order to test, set the setting to 0 (zero) in the “Allowance for point position differences” in the setup panel of Touch Driver.