- DVD Mechanism Type: CDM86-DVBU101
- Optical Pick-up Block Name: KHM-310CAB
- Tape Transport Mechanism Type [A]: CMAL5Z230
- Tape Transport Mechanism Type [B]: CMAL1Z254A
TO START DVD SERVICE MODE
- Press the [POWER] button to turn the power on.
- Touch the [DVD] sensor to select the “DVD”.
- Press the [EJECT] button and touch two sensors of [STOP] , [VOLUME+] simultaneously.
- The message “SERVICE IN” will be displayed on the fluorescent indicator tube and the Rimocon Diagnosis Menu is displayed on the on-screen display on the monitor TV as follows.
- The model name, IF-con version and Syscon version is displayed at the bottom of the on-screen display.
Remocon Diagnosis Menu
0. External Chip Check
1. Servo Parameter
Check
2. Drive Manual
Operation
3. Emergency History
4. Version Information
5. Video Level
Adjustment
Model Name :AZXD_XX
IF-con :Ver.xx.xx
(xxxx)
Syscon :Ver.x.xxx
- To execute each function, press its number by using numeric button on the remote commander (RM-AMU001)
- To release from this mode, press the [POWER] button to turn the power off.
DRIVE MANUAL OPERATION
- The Drive Manual Operation menu consists of five main functions.
- On the Remocon Diagnosis Menu screen, press [2] button on the remote commander, and the following Drive Manual Operation menu will be displayed.
Drive Manual Operation
1. Servo Control
2. Track/Layer Jump
3. Manual Adjustment
4. Tray Aging Mode
5. MIRR time Adjust
0. Return to Top Menu
MIRROR TIME ADJUST
- On the Drive Manual Operation menu screen, press [5] button on the remote commander, and the following MIRR time Adjust Menu will be displayed.
MIRR time Adjust Menu
1. CD MIRR time Check:
2. DVD MIRR time
Check:
3. Threshold:
4. Save to EEPROM
5. Default set MIRR
time
[Open] Tray open
[Close] tray close
[0] Return to previous
menu
There are five main commands in the Mirr
time Adjust menu. The functions of each command are described in the following
page.
- CD MIRR time Check: This command checks the Mirror time value for CD disc.
- DVD MIRR time Check: This command checks the Mirror time value for DVD disc.
- Threshold: This command displays the threshold value between CD and DVD mirror time.
- Save to EEPROM: This command saves an adjusted mirror time value to the EEPROM.
- Default set MIRR time: This command will set CD and DVD mirror time to firm ware default value.
OPEN CLOSE
Pressing the [EJECT] button controls the tray for disc change during mirror time
adjustment.
[0] Return to previous menu.
Press the [0] button on
the remote commander to return to previous menu.
EXECUTING MIRROR TIME ADJUSTMENT
In order to execute mirror time adjustment,
the following standard procedures must be followed.
- Set to the MIRR time Adjust Menu mode.
- Press the [5] button on the remote commander to select the “5 Default set MIRR time”.
- Press the [3] button on the remote commander to select the “3 Threshold”.
- Check the value of Threshold on the screen. If it is 75, go to next step. If it is not so, return to step 2.
MIRR time Adjust Menu
1. CD MIRR time Check:
2. DVD MIRR time
Check:
3. Threshold: 75
4. Save to EEPROM
5. Default set MIRR
time
[Open] Tray open
[Close] Tray close
[0] Return to previous
menu
5. Insert the DVD test disc (HLX-504) (Part
No.J-6090-088-A)
6. Press the [2] button on
the remote commander to select the “2 DVD MIRR time Check”.
T. Wait for hexadecimal value to display on
the screen.
8. Check the value (##) of DVD MIRR time on
the screen. If ## is 28 to 70, go to next step. If it is not so, return to step
5.
MIRR time Adjust Menu
1. CD MIRR time Check:
2. DVD MIRR time
Check: $$ ##
3. Threshold:
4. Save to EEPROM
5. Default set MIRR
time
[Open] Tray open
[Close] Tray close
[0] Return to previous
menu
9. Press the [4] button on
the remote commander to select the “4. Save
to EEPROM”
10. Check that $$ is the
same as the value of ## on the screen. If it is not so, return to step 5.
11. Take out the DVD test disc (HLX-504)
and insert the CD test disc (YEDS-18) (Part No.3-703-998-01).
12. Press the [1] button on the remote commander to select the “1.CD MIRR time
Check”.
13. Wait for hexadecimal value to display
on the screen.
14 Check the value (@@) of CD
MIRR time on the screen. If @ @ is 5A to E8, go to next step. If it is not so,
return to step 11.
MIRR time Adjust Menu
1. CD MIRR time Check:
&& @@
2. DVD MIRR time
Check: $$ ##
3. Threshold:
4. Save to EEPROM
5. Default set MIRR
time
[Open] Tray open
[Close] Tray close
[0] Return to previous
menu
15. Press the [4] button on the remote commander to select the “4. Save to EEPROM”.
16. Check that && is
the same as the value of @@
on the screen. If it
is not so, return to step 11.
17. Take out the CD test disc (YEDS-18)
18. Release the MIRR time Adjust Menu mode.
EXECUTING IOP MEASUREMENT
1. Set to the Drive Manual Operation mode.
2. Press the [3] button on
the remote commander, and the following Manual Adjust menu will be displayed.
Manual Adjust
1. Track Balance
Adjust:
2. Track Gain Adjust:
3. Focus Balance
Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve (FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
[UP]|[DN]
Change value
[Return: Return to previous menu.
3. Press
the [6] button on the remote commander to select
the “6. IOP”.
4. Wait for hexadecimal Value to display on the
screen.
Manual Adjust
1. Track Balance
Adjust:
2. Track Gain Adjust:
3. Focus Balance
Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop: ED
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
UP/DN: Change value.
[Return]:
Return to previous menu
5. Convert
value (ED) from hexadecimal to decimal using conversion table.
6. If
the remainder is smaller than 93 (decimal), then it is OK. However if the value is higher than 93, then
the BU (base unit) is defective and need to be change.
7. Release
the Manual Adjust menu mode.
DVD RAM CLEAR
- This mode clears DVD data stored in the DVD RAM to initial conditions.
- On the Rimocon Diagnosis Menu screen, press [4] button on the remote commander to select the “4.Version Information”.
- Press in order of [MENU] button and [CLEAR] button on the remote commander.
- Press in order of [MENU] button and [CLEAR] button on the remote commander to clear DVD data.
- The message “Initialize all data” will be displayed on the screen.
- The message will change into “Initialize all data Complete” in about six seconds, and the clearness of the DVD data is completed.
