Tuesday, April 02, 2013

BenQ LCD TV SU-4231 -PAL - WELTREND FOR BenQ LCD TV - SOFTWARE UPDATE - ASCII CODE CHART - ADJUSTMENT PROCEDURE




ISP FOR WELTREND
  • Install Weltrend MCU ISP tool :  Press setup.exe
Install USB ISP kit Driver :
  • Take USB ISP kit connect to PC USB port, Windows XP will detect new device, Follow up the below install process.
                                                   Click on images to Enlarge

  • Connect the cable between TV VGA and USB ISP kit, then turn on the TV power.
Open “Weltrend MCU ISP”

  • The position is from ”start” à programs” à  “Weltrend MCU ISP” à “Weltrend MCU ISP” open MCU ISP tool the same as below photo.
Check F/W version of MCU
  • Entering GProbe-5(The process the same as above description)
  • Key in -appstest 60 0x26 0xf2 on the command then press execute to show result .See the below photo
  • Look up the word in the ASCII code chart that means 0
  • Key in appstest 60 0x26 0xf3 and appstest 60 0x26 0xf4 in turn to look up the represented meaning in the ASCII code chart.


ASCII CODE CHART
MCU WT6702F firmware version format:

version code 2 + version code 1 + version code 0
Type command as follows to get version code:
appstest 60 0x26 0xf2 ---> read version code 2
appstest 60 0x26 0xf3 ---> read version code 1
appstest 60 0x26 0xf4 ---> read version code 0

Software content
File name: MCU_ISP_SETUPV0.3
File name: 6702F_P002.hex

ADJSUTMENT / ALIGNMENT PROCEDURE
Item
Specification
Inspection Method

1. Prepare Process
Make sure that each voltage
value on the power board is
correct
+12V : 12V +1.2V,-0.8V
+5V : 5.2V ± 0.3V
+24V : 24V ± 2V
+5VSub : 5.2V ± 0.3V

1.  Use dummy load
2.  Use DVM meter to
measure and adjust the
voltage
2. Continuous Process
1.  Power On
2.  After assembly, check each voltage output on power
board
+12V : 12V +1.2V,-0.8V
+5V : 5.2V ± 0.3V
+24V : 24V ± 2V
+5VSub : 5.2V ± 0.3V

1.  Switch to video mode
2.  Input video pattern
Multi-Burst ( Use Fluke
54200 or Shibasoku
TG19CC)
3.  Use DVM to measure the
voltage
3. Preset Mode
as below


4. VGA
Equipment : LEADER LT 447
Test Pattern : 8 color bar, and set to
100% output level
(1) Press Menu key and
then select setup page
(2) Scroll down the light bar
on “Reset all settings”
and then press “right +
down” key
(3) Select item 2 and scroll
Down to”Calibration”
and select to”signal”
then press enter key.

5. Y,Pb,Pr
Equipment : LEADER LT 447
Test Pattern : 8 color bar, and set to 100% output level
(1) Press Menu key and
then select setup page
(2) Scroll down the light bar
on “Reset all settings”
and then press “right +
down” key
(3).Select item 2 and scroll
Down to”Calibration”
and select to”signal”
then press enter key.

6. AV/ SV
Equipment : LEADER LT 447
Test Pattern : 8 color bar, and set to 100% output level.
(1) Press Menu key and then
select setup page
(2) Scroll down the light bar
on “Reset all settings”
and then press “right +
down” key
(3).Select item 2 and scroll
Down to”Calibration”
and select to”signal”
then press enter key.
PRESET MODE [Click on Images to Enlarge]