SERVICE MODE
- This mode is used to display seven kinds of test patterns [Horizontal lines, Vertical lines, Dots, Crosshatch, White cross, Black cross and White (No pattern)] in the four colors (White, Red, Green and Blue).
- On the service mode, displays above patterns by each color without test equipment such as PC or SG. Use the service mode for simplified adjustments by your eyes and so on.
- Select "SERVICE MODE" on "EXT OPTION" menu and press "ENTER" button on the remote control unit. [Exit Option Menu described below].
- In the service mode, pressing the up-arrow or down-arrow button allows the test pattern selection and the left-arrow or right-arrow button the color selection (White / Red / Green / Blue).
- To exit, press "MENU" button on the remote control unit.
EXIT OPTION
This projector has EXT OPTION
in addition to standard on-screen menus.
There are SELF CHECK and SERVICE MODE for service, etc.
- Press "MENU" button on the remote control unit to display "MENU" screen, then select "OTHER SETUP" and press "ENTER" button.
- Select "HIGHTLAND" on "OTHER SETUP" menu and press "ENTER" button 3 seconds or longer. MENU à OTHER SETUP à HIGHTLAND
EXIT OPTION [DISPLAY DETAILS]
- FREEZE MSG: Switching ON/OFF "FREEZE" on-screen display
- ANGLE RESET: Resetting "AUTO SETUP (Correcting keystone distortion)" reference level. [Normally, do not select. (Angle reset data will be rewritten.)]
- FAN FULLMODE: Setting the cooling fan motor rotation speed/ Switching ON "FAN FULLMODE", the rotation level of the fan becomes high-speed rotation (fixed). Moreover, when "FAN FULLMODE" is ON, changing "HIGHTLAND" in OTHER SETUP becomes impossible (setting FAN FULLMODE is given priority more than HIGHTLAND).
- AUTOSETUP: Setting AUTO SETUP mode {STANDARD: To set the normal mode (the dot clock is adjusted strictly). SPECIAL: To set the special mode (the dot clock is adjusted roughly)} [Do not change the initial setting (STANDARD).]
- SYNC: Setting SYNC processing mode { STANDARD: To set the normal mode. SPECIAL: To set the special mode (noise reduction mode)} Do not change the setting when it is possible to receive normally. Change the setting only when the image is not displayed normally because of the sync signal noise of connected equipment.
- SELF CHECK: To enter the self-check mode.
- SERVICE MODE: To enter the service mode.
- FLICKER ADJ: To enter the flicker adjustment mode.
- H PLL: When non-standard signal of VIDEO/S-VIDEO is inputted (VCR, VHD, etc.), horizontal synchronization might be disordered according to connected equipment. In this case, set H PLL to OFF.
- Press "MENU" button on the remote control unit to CANCEL EXT Option.
SELF CHECK MODE
This
mode is used to narrow down the location of the failure.
- Select "SELF CHECK" on "EXT OPTION" menu and press "ENTER" button on the remote control unit.
- Press "MENU" button on the remote control unit to cancel self check mode.
FLICKER ADJUSTMENT MODE
- Select "FLICKER ADJ" on "EXT OPTION" menu and press "ENTER" button on the remote control unit. {"DESK setting (blue)" is displayed when entering the adjustment mode.}
Adjustment
Display and Contents
- Setting value is increased and decreased with the right-arrow and left-arrow buttons.
- ß Decrease, à Increase
- Adjust the setting value to minimize the flicker on the screen.
- Execute the adjustment by 6 patterns below.
- The pattern (adjustment display) is switched with the up-arrow and down-arrow buttons.
- [UP] Forward direction, [DN] Reverse direction
- There are 6 patterns of "DESK setting (blue)", "DESK setting (red)", "DESK setting (green)", "CEILING setting (blue)", "CEILING setting (red)" and "CEILING setting (green)".
- The setting value is saved into this projector when the pattern is switched.
- Press "MENU" button on the remote control unit TO CANCEL. [When "MENU" button is pressed, the setting value at that time is saved into this projector and the adjustment mode is canceled.]
