At the Customer Service menu functions can BeoVision 7 individually adjusted and optimized, for which purpose the support of the normally Retail partner or service center is required.
The
service center can also find basic device information directly on the screen
instead of on a label on the back read.
Customer
Service Call up the menu:
- Press MENU on Beo4 to enter the "TV Set-up Menu."
- The cursor to "OPTION" set. The RED button and within three second press GO.
Status
information
- Type number
- Item number
- SerialNumber
- Option setting
- AP SW
- IOP SW
- M2 SW
- STAT SW DISP
- STB TABLE C SW
- Projector Table
For
future use.
- DSM SW
- DVD - FEP SW
Select
new values: [<< >>]
New store values: GO.
SOUND
- AVC ON / OFF (default ON)
- AVC AVC is turned ON
- AVC AVC OFF is disabled
- WSS DETECT STATUS ON / OFF DETECT / BROADCAST ONLY (default DETECT ON)
- Wide Screen Signalling (WSS) is the signal for the correct aspect ratio setting. The signal is usually available on DVD and can of TV channels be aired.
Only
TV tuner signal.
Signal
detection for signals from the TV tuner enabled.
The
signal is sent by the broadcaster.
- DETECT ON
- DETECT OFF
Can
be used with poor signal quality when the image format arbitrarily replaced.
This
can occur when TV tuner signals with poor signal to noise ratio.
AutoFormat
ENABLED / DISABLED (default ENABLED)
Auto
Format sets the best ratio and uses this Black Bar Detection.
The
image can always be selected manually using the Beo4. ENABLED
It
is automatically selected the best picture format.
- DISABLED
The
image format is either the default setting or with the Beo4.
- 4:3 FORMAT ON / OFF (default OFF)
It
can be activated manually with Beo4.
4:3
is only enabled in FORMAT first ON
4:3
FORMAT is enabled in the first OFF
4:3
FORMAT is disabled in the first
- CINEMA TIMINGS
Home
Cinema is with, ASPECT 0 activated 'or disabled.
- HDTV DETECTION
Disabled:
If an HDTV source is selected, switches the TV to always
Y
/ Pb / Pr input.
- EXTRA BLANKING
- CINEMA ON
Projector
screen, via motorized curtains and lighting
Expander
boxes are used. For example, a motor
Cinema
projection screen on the Control 1 and Control 2 lights at Cinema be connected.
Both
outputs are connected with open collector and can connected devices do not
provide power, so it is an external Power required.
- CINEMA CONTROL 1 and 2
,
Home Cinema 'is activated, the output after the delay time on 'Closed' set
(low). Here, the supply voltage of the external power supply from the open
collector 'to ground switched. If, for As a relay is a motor connected to the
projector screen, it turns, and the Projector screen moves down. If an Expander
for other devices is connected, the input is on, switched low '.
- CINEMA READY
- STAND DONE
- CINEMA OFF
If,
for example, a relay of a motor is connected to the projector screen, it
switches, and the projector screen moves up. If an Expander for other Equipment
is connected, the input is on, shift up '.
- READY FOR CINEMA
- TURN STATE DELAY
- EXTRA BLANKING
Box
slow sync on a satellite channel.
Depending
on the setting of the selected input connector, the display of the TV image
delayed (blanked).
- MONITOR SERVICE MENU
Described
in section settings.
- MONITOR INFO
The
line "STB TABLE 1.0" shows the version of the conversion of set-top
box Beo4 remote control codes in code. The line will only appear if the M2
processor was flash programmed.
"VARIANT"
displays on the TV to which the AP is set SW. Factory setting.
Type,
product and serial numbers
PIN
code status. Indicates if the master code is entered correctly (STORED /NOT
STORED)
Option
programming
Last
five TV error
Last
ML error
Last
AVL error of the AV jacks.
- OPTION SETTING
Option
1 = The TV and the audio system (BeoLink system) are located in the same room.
Option
2 = The TV and the audio system (BeoLink system) are in different rooms.
Option
4 = not connected to Link Two televisions in the same room.
Option
5 = The TV and the audio system (BeoLink system) are located in same link room.
Option
6 = The TV set is the only one in the link room.
- ERROR: TV
The
five units are as error and error codes with the System time supplied stating
month / day (four digits) of their occurrence displayed. The most recent error
is displayed above. Since the TV does not Hardware clock has the
Monats-/Datumsangabe not exact, but it can be used to check whether the same
date further error occurred is.
- TV error
No
errors registered
DF
data error
POR1
power-reset error 1
POR2
power-reset error 2
PDD
error when switching off
YZ-XX
(XX = IIC address
Y
= IIC bus 1 or bus 2
Z
= any IIC bus segment A / B / C / D)
- ML-error
No
errors registered
CI
address configuration impossible
TD
ML data pulled to ground
TU
ML data to "High" pulled
?
Other unidentifiable error possibilities.
- AVL error
No
errors registered
TI
transfer impossible
Blocked
TD data connection.
Motorized
stand
- Motorized stand-error codes
ST-02
calibration error too many positions
ST-03
calibration error EEPROM
ST-04
calibration error Transducers
ST-05
calibration error position
After
the elimination of a fault, which causes the display of an error code has, then
the error code will be deleted. Purpose GO MONITOR Information menu press.- DVD service menu
Provides
access to the DVD service, which inter alia be checked whether the DVD region
code matches under the "region" displayed.
Open
Zone:
Press
the GO button, the TV picture appears
DVD
press and wait for the DVD image
Press
MENU and then press 0 0 GO
The
DVD-Service menu
Press
the GO button, the DVD service menu appears
To
exit the DVD service menus on the TV to standby switch.
