PHILIPS - SRP 5017-27 REMOTE CONTROL SETUP PROCDEURE

Philips remote control set-up procedure

SETUP PROCEDURE
Initial setup

• Make sure the receiving device is able to respond. E.g. when you try to repair the Play button for your DVD player, make sure to insert a DVD into the DVD player otherwise the Play button is not able to function.
• Press the button that does not function, keep it pressed and immediately release it when the device responds.  Repeat this for every button that does not function.
• If the button still does not function as expected, try pressing it again for a longer period of time.

After initial setup

• Make sure the receiving device is able to respond. E.g. when you try to repair the Play button for your DVD player, make sure to insert a DVD into the DVD player otherwise the Play button is not able to function.
• Select the device that you wish to operate.
• Press the DVD device selection button to select DVD.
• Keep buttons [1] & [4] pressed simultaneously for [5] seconds.  The red setup light lights up.  The remote control is now in setup mode.
• Press and hold the button that does not function and immediately release it when the device responds.
• If the button still does not function as expected, try pressing it again for a longer period of time.
• Press DVD selection button ‘twice’ to save your settings and exit setup mode
• When no button is pressed for [5 minutes] or more, the remote control will exit setup mode, automatically saving all your settings.

Controlling combo devices

• Some combo devices (e.g. TV/DVR, TV/DVD, DVD/DVR, etc.) have separate buttons on the original remote control to select the part of the combo device to be controlled.
• For example, if your combo device is a DVD/DVR then its original remote control might have separate DVD and DVR buttons for selection of the combo part you wish to operate.
• The equivalent button functions can be found on your Philips remote control by using the device selection buttons.

Testing the universal remote control

• It is advised to test whether your device(s) already respond(s) to the SRP5107 before setting it up. The example below instructs you how to do this for your TV. You can repeat the same steps for other devices (DVR, DVD player/recorder, Cable/Satellite box, DTV, VCR, HD and auxiliary equipment) which you want to operate using the SRP5107.
• Switch ON your TV manually or use the original remote control for this. Tune to channel 1.
• Press the ‘TV’ device selection button to select ‘TV’.
• The red setup light blinks.  If it does not blinks, check whether the batteries are properly inserted.
• See whether the buttons you need for operating  your TV are working. 
• If the TV responds as it should to all of the button commands, the remote control is ready to use.  If the device does not respond at all or not to all of the button commands, it should be setup with your device.

Setting up the remote control.

• The example below instructs you how to set up your universal remote control for your TV. You can repeat the same steps for other devices (DVR, DVD player/recorder, Cable/Satellite box, DTV, VCR, HD and auxiliary equipment) which you want to operate, using the universal remote control.

1. TV:  Traditional TV, LCD/Plasma TV, flat panel TV, projection TV and 3D TV, TV part of TV/VCR, TV/VCR/DVD and TV/DVD combos.
2. DVR:  Digital/Personal Video Recorder (DVR/PVR), TiVo, DVR part of DVR/SAT, DVR/Cable and DVR/DVD combos.
3. DVD:  DVD player/recorder (DVDR/DVDRW), DVD/Hard Disk Drive combination (DVDR-HDD), Blu-Ray player, High Definition DVD player (HD-DVD), DVD part of TV/DVD, V/VCR/DVD, DVR/DVD and VCR/DVD combos.
4. CBL/SAT:  Cable box, satellite receiver, Internet Protocol TV (IPTV), Free To Air TV, High Definition Television decoder (HDTV), Digital Television (DTV), TiVo, SAT/Digital TV (DTV)/WebTV, DTV/Advanced Television Systems (ATSC) - Digital To Analog Converter, CBL part of DVR/Cable combos and SAT part of DVR/ SAT combos.
5. VCR:  Video cassette player/recorder, VCR part of TV/VCR, TV/VCR/DVD and VCR/DVD combos.
6. AUX:  Auxiliary equipment: CD, Audio System, Laser Disc, Digital Picture Frame, Media Center PC, Home Automation, Home Theater in a Box (HTIB).
7. HD:  Any of the above listed devices.

Example: setting up the universal remote control to operate your TV:

1. Switch ON the TV manually or use the original remote control for this. Tune to channel 1.
2. Press and Hold the TV device selection button for 5 seconds until the red setup light blinks.  The remote control is now in setup mode.
3. Look up the four digit code for your brand in the brand list.
4. Use the digits buttons to enter the code for your brand.  If red setup light turns off, an invalid code was entered. In this case try again.
5. Aim the remote control at the TV.  Press and Hold the ‘Power’ button.  Release it immediately as soon as the TV switches off.  This step normally takes between 5 and 60 seconds.  In extreme circumstances this step can take up to 15 minutes. 
6. Switch on the TV.  Try out the buttons you need to operate it.  If a button does not work as expected, Press and Hold that button.  Release it immediately as soon as it works. 
7. Press the device selection button ‘twice’ to finish the setup.  When no button is pressed for 5 minutes or more, the remote control will exit setup mode automatically saving all your settings.

• If you made a mistake; Press the Device Selection Button ‘Twice’ to exit setup.  The red setup light turns off.  Restart from beginning.
• If the device does not respond at all or not to all of the button commands or if you cannot find the code for your brand, enter ‘9, 9, 9, 9’ in step 3 and continue with step 4.
• The remote control will now search its full database for a code that works with your TV. Full database search maytake up to 15 minutes.

Resetting a button to its original function

1. When resetting a button to its original function, any learned function stored under the button will be deleted.
2. In the current device mode, keep digit buttons 1 & 6 pressed simultaneously  for 5 seconds, until the red setup light lights up.  The remote control is now in setup mode.
3. Press digit buttons 9,9,6 in that order.  After each button press, the red setup light blinks once.
4. Press the button you wish to reset ‘twice’.  For each button press the red setup light blinks once.
5. The red setup light will blink one more time to confirm that the button was successfully reset to its original function.
6. The button can now also learn a new function, if desired.

Use ‘9999’ as 4-digit code in case you cannot find your brand in the complete brand list. Note that using ‘9999’ may result in a long setup (up to 15 minutes).

Check this for setup code list