- Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order.
===================================
MODEL : *******
Version : *.**
Region : *
EEPROM CLEAR : CLEAR EXIT: SELECT
===================================
- Press [CLEAR] button on the remote control unit.
=================================
MODEL : *******
Version : *.**
Region : *
EEPROM CLEAR : OK
EEPROM CLEAR : CLEAR EXIT: SELECT
=================================
- When “OK” appears on the screen, the factory default will be set. Then the firmware renewal mode is complete.
- To exit this mode, press [CH UP / DN] or [SELECT] button to go to TV mode, or press [POWER] button to turn the power off.
TV SECTION
Use
the service remote control unit.
- Turn the power on. (Use main power on the TV unit.)
- Press [DISC MENU] button on the service remote control unit to enter the Service mode.
- Press [VOL DN] button on the service remote control unit twice, and confirm that OSD indication is “7F = FF.” If needed, set it to become “7F = FF” by pressing [CH UP / DN] buttons on the service remote control unit.
- Confirm that OSD indication on the four corners on TV screen changes from on and off light indication to red by pressing a [DISPLAY] button. (It takes one or two seconds.)
- Turn the power off by pressing main power button on the TV unit, and unplug the AC cord from the AC outlet
FIRMWARE RENEWAL MODE
- Turn the power on and press [SELECT] button on the remote control unit to put the TV/DVD into DVD mode. Then remove the disc on the tray. (It is possible to move to F/W version up mode only when the TV/DVD is in DVD mode with the tray opened.).
- To put the TV/DVD into F/W version up mode, press [9], [8], [7], [6], and [SEARCH MODE] buttons on the remote control unit in that order.
====================================
F/W Version Up Mode Model No : *******
VERSION : *.**
Please insert a DISC
for F/W Version Up.
========================================
Version Up Mode Screen
The TV/DVD can also enter the version up mode with the
tray open. In this case, Fig. will be shown on the screen while the tray is
open.
- Load the disc for version up.
- The TV/DVD enters the F/W version up mode automatically. If you enter the F/W for different models, “Disc Error” will appear on the screen, then the tray will open automatically.
=====================================
F/W Version Up Mode Model No : *******
VERSION : *.**
************.ab5
VERSION :
Reading...
=====================================
The
appearance shown is described as follows:
No.
|
Appearance
|
State
|
1
|
Reading...
|
Sending
files into the memory
|
2
|
Erasing...
|
Erasing
previous version data
|
3
|
Programming...
|
Writing
new version data
|
- After programming is finished, the tray opens
automatically and the checksum will be shown on the screen. At
this time, no button is available.
========================================
F/W Version Up Mode Model No : *******
VERSION : *.**
************.ab5
VERSION :
Completed
SUM : 7ABC
========================================
- Remove the disc on the tray.
- Press [CH UP / DN] button on the unit to go to TV mode, or press [POWER] button on the unit to turn the power off.
- Press [SELECT] button on the remote control unit to put the TV/DVD into DVD mode again.
- Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order.
============================================
MODEL : *******
Version : *.**
Region : *
EEPROM CLEAR : CLEAR EXIT: SELECT
============================================
- Press [CLEAR] button on the remote control unit.
=========================================
MODEL : *******
Version : *.**
Region : *
EEPROM CLEAR : OK
EEPROM CLEAR : CLEAR EXIT: SELECT
=========================================
- When “OK” appears on the screen, the factory default will be set.
- Then the firmware renewal mode is complete.
- To exit this mode, press [CH UP / DN] or [SELECT] button to go to TV mode, or press [POWER] button to turn the power off.
